WAGO 16-channel, 24VDC User manual

Brand: WAGO

Model: 16-channel, 24VDC

Type: User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Fr ontseite 2015 - mit DocVariab len (Standard) @ 9\mod_1285 229289866_0.doc x @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

750-1400

16DI 24V DC 3.0ms, ribbon cable

16-

Channel Digital Input Module 24 V DC, Ribbon

cable, high-

side switching

Version 1.2.0

Pos: 3 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/I mpressum für Standar dhandbücher - allg. Angaben, Anschrif ten, Telefonnummern und E-Mai l-Adress en @ 3\mod_1219151118203_21. docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Liste für Textmarke Einband_vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhaltsverzei chnis - Überschrif t oG und Verzeichnis @ 3\mod_1219 151230875_21.doc x @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 14

3.2 Connectors ............................................................................................... 15

3.2.1 Data Contacts/Internal Bus ................................................................. 15

3.2.2 Ribbon Cable and CAGE CLAMP

Connectors ............................... 16

3.3 Display Elements .................................................................................... 17

3.4 Operating Elements ................................................................................. 17

3.5 Schematic Diagram ................................................................................. 18

3.6 Technical Data ........................................................................................ 19

3.6.1 Device ................................................................................................. 19

3.6.2 Communication .................................................................................. 19

3.6.3 Supply ................................................................................................. 19

3.6.4 Inputs .................................................................................................. 19

3.6.5 Connection Type ................................................................................ 19

3.6.6 Climatic Environmental Conditions ................................................... 20

3.7 Approvals ................................................................................................ 21

3.8 Standards and Guidelines ........................................................................ 22

4 Mounting ..................................................................................................... 23

4.1 Mounting Sequence ................................................................................. 23

4.2 Inserting and Removing Devices ............................................................ 24

4.2.1 Inserting the I/O Module .................................................................... 24

4.2.2 Removing the I/O Module .................................................................. 25

5 Connect Devices ......................................................................................... 26

5.1 Connecting a Conductor to the CAGE CLAMP

................................... 26

6 Process Image ............................................................................................. 27

7 Accessories .................................................................................................. 28

8 Use in Hazardous Environments .............................................................. 29

8.1 Marking Configuration Examples ........................................................... 30

8.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 30

4 Table of Contents WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

8.1.2 Marking for America According to NEC 500 .................................... 35

8.2 Installation Regulations ........................................................................... 36

8.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 37

8.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 38

8.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)39

8.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 40

8.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 41

List of Figures ...................................................................................................... 42

List of Tables ........................................................................................................ 43

=== Ende der Liste für Textmarke Verzeichnis_ vorne ===

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften für alle Ser ien/Hinweise zur Doku mentation/Hinwei se zu dieser Dokumentati on - Überschrif t 1 @ 4\mod_1237987661750_21.doc x @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Hinweise/Hinwei s: Dokumentation aufbe wahren @ 4\mod_1237987 339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften für alle Seri en/Hinweise zur Dokume ntation/Gültigkei tsbereich - Übersc hrift 2 @ 12\mod_1338912448776_ 21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Gültigkeitsber eich/Gültigkeit sbereich Dokumenta tion Busklemme 750-xxxx, ohne Variantenangabe @ 14\ mod_1358944037947_2 1.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-1400

(16DI 24V DC 3.0ms, ribbon cable).

Pos: 11 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Hinweise/Acht ung: Hinweis zur Dokume ntation Busklemmen 750- xxxx @ 4\mod_1237986979 656_21.docx @ 29023 @ @ 1

The I/O module 750-1400 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentatio n/Urheberschut z ausführlich @ 4\mod_123 5565145234_21.doc x @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 12.3 /Alle Serien (A llgemeine Module)/Ü berschriften für alle Serien/Hinweise zur Dok umentation/Symbo le - Überschrift 2 @ 13\ mod_1351068042408_21.doc x @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12.4.1 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden a llgemein_ - Erläuterung @ 13\ mod_1343309450020_ 21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.2 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden dur ch elektrischen Stro m_ - Erläuterung @ 13\mod_134 3309694914_21.doc x @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.3 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Warnung/Warnung: _Warnung vor Personenschäd en allgemein_ - Erläuter ung @ 13\mod_134330987704 1_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12.4.4 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Vorsicht/Vorsi cht: _Warnung vor Personen schäden allgemein_ - Erläuterung @ 13\mod_1343310 028762_21.doc x @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12.4.5 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden al lgemein_ - Erläuteru ng @ 13\mod_1343310134623_21. docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.6 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden dur ch elektrostatische Auf ladung_ - Erläuter ung @ 13\mod_13433102277 02_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.7 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweis e/Hinweis/Hinweis: _W ichtiger Hinweis al lgemein_ - Erläuterun g @ 13\mod_1343310326906_21. docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12.4.8 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Information/I nformation: _Wei tere Information allgemein_ - Erläuterung @ 13\mod_134 3310439814_21.doc x @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 12.6 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Darstellung der Zahlensysteme - Übersc hrift 2 und Inhalt @ 3\mod_122 1059454015_21.doc x @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12.7 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentatio n/Schriftkon ventionen - Überschri ft 2 und Inhalt @ 3\mod_122105952143 7_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Wichtige Erläu terungen/Wichti ge Erläuterungen - Übersc hrift 1 @ 4\mod_1241428899156_ 21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Wichtige Erläut erungen - Einleitun g @ 3\mod_1221059818031_21. docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /Alle Serien (A llgemeine Module)/Ü berschriften für alle Serien/Wichtige Er läuterungenRechtlic he Grundlagen - Übersc hrift 2 @ 3\mod_12210606263 43_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Änderungsvorb ehalt - Überschrif t 3 und Inhalt @ 3\mod_12210600364 84_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Personalqua lifikationPerson alqualifikation 750- xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240612080 46_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Bestimmungsge mäße VerwendungBes timmungsgemäße Verwendun g 750-xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Technischer Zusta nd der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_12210 60446109_21.docx @ 217 23 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 15.8 /Alle Serien ( Allgemeine Module)/Ü berschriften für alle Serien/Wichtige Er läuterungenSicher heitshinweise - Übersc hrift 2 @ 6\mod_1260180299987 _21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheitshi nweise/Einleitung Si cherheitshin weise Hardware @ 6\mod_1260 180170493_21.doc x @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.10.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Nicht an Gerä ten unter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Gefahr/Gefahr: Einbau 0750-xxxx nur in Gehäusen, Schränken oder elektrischen Betri ebsräumen! @ 6\mod_126018 0556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.10.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Unfallver hütungsvorschr iften beachten! @ 6\mod_1260 180657000_21.doc x @ 46735 @ @ 1

Pos: 15.10.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Auf normgerec hten Anschluss achten! @ 6\mod_1260180753479_ 21.docx @ 46739 @ @ 1

Pos: 15.11.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte aust auschen! @ 6\mod_126018 0857358_21.doc x @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.11.2 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Geräte vor kriechenden und isolier enden Stoffen schütze n! @ 6\mod_126018103621 6_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.11.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Reinigung nur mit zulässigen Materi alien! @ 6\mod_12601812 03293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.11.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Kein Kontak tspray verwenden! @ 6\ mod_1260181290808_21. docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.11.5 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Verpolun g vermeiden! @ 6\mod_1260184 045744_21.doc x @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.11.6 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Elektrosta tische Entladung ver meiden! @ 6\mod_1260181 364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Gerätebeschr eibung - Überschr ift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/An wendung/DI/Anwendung 7 50-x4x x DI @ 3\mod_12 33762736718_21.doc x @ 27108 @ @ 1

The digital input module 750-1400 (16DI 24V DC 3.0ms, ribbon cable) receives

control signals from digital field (e.g. of sensors, transmitters, switches or

proximity switches).

Pos: 18.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-140x 16 DI 1-Leiter Stecker @ 3\mod_1233763103859_2 1.docx @ 27116 @ @ 1

The I/O module has 16 input channels and connects to electronic modules via 20-

pin ribbon cable.

Pos: 18.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/A llgemein/Verweis auf Kapitel "Anschlüsse" @ 8\mod_1276775378035_21. docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/A llgemein/Verweis auf Elektronikbaustei ne als Zubehör @ 4\mod_123 6063336171_21.doc x @ 27953 @ @ 1

Suitable electronic modules are available as accessories from WAGO.

Pos: 18.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-x4xx DI RC-Filter 3, 0 ms @ 3\mod_1233755071062_21.doc x @ 27080 @ @ 1

Each input channel has a RC noise rejection filter with a time constant of 3.0 ms.

Pos: 18.6 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-x4xx DI HSS / positi vschaltend (24 V) @ 3\mod_123383 1724648_21.doc x @ 27231 @ @ 1

The I/O module inputs provide high-side switching. If the 24 V potential for field

power is switched to an input connection, the signal status for the corresponding

input channel is set to “high”.

Pos: 18.7 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ LED-Anzeige/LED Zustan d Signal @ 3\mod_12337552585 78_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 18.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/LE D-Anzeige/Verwei s auf Kapitel "Anzeigee lemente" @ 5\mod_12460105 25000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.9 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Versorgung 2 4 V über CAGE CLAMP-Anschlüs se oder Elektronikbaustein @ 4\mod_12 36062578765_21.doc x @ 27950 @ @ 1

The 24 V power supply can be fed in via the 24 V and 0 V CAGE CLAMP

connectors, or as an alternative, via the electronic module's ribbon cable.

Pos: 18.10 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/Hin weis/Hinweis: Potenti aleinspeiseklem me einsetzen! (kei ne LK) @ 3\mod_1226499089640_ 21.docx @ 25026 @ @ 1

Use a supply module!

Use a supply module for field-side power supply of downstream I/O modules.

Pos: 18.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Galvanisc he Trennung Feld/Syst em @ 3\mod_1233756478 750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 18.12 /Serie 750 ( WAGO-I/O-SYSTEM)/ Gerätebeschreibung/ Einleitung/Versor gung/Anordnung un ter Berücksichtigung der Leistungskontak te beliebig @ 3\mod_123375 6233468_21.docx @ 2709 9 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.13 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ei nsatzbereich/ Einsatzbereich 750-xxxx a lle Koppler/Contr oller ohne Einschränkung @ 3\ mod_1232541691906_21. docx @ 26522 @ @ 1

The I/O module 750-1400 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 19 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 20 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Ansicht - Übersc hrift 2 @ 4\mod_124098421 7343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 21 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Digital eingangsklemmen/ Ansicht 750-140x 16 DI Stecker Flachbandkabel - Abb @ 3\ mod_1224766361109_21. docx @ 24649 @ @ 1

Figure 1: View

Pos: 22 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Ansic ht mit Flachbandkabel-Ansc hluss - Legende @ 20\mod_1 412696658916_21.doc x @ 165335 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with

Mini-WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

Connector

“Device Description” > “Connectors”

5 Release tab

“Mounting” > “Inserting and Removing

Devices”

CAGE CLAMP

connectors

“Device Description” > “Connectors”

Pos: 23 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 24 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Anschlüsse - Überschrift 2 @ 4\mod_1240984 262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 25 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Da tenkontakte/Klem menbus - Überschrif t 3 @ 6\mod_1256294684083_21.d ocx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 26.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Datenk ontakte - Feldbuskopp ler/-controller , Abbildung und Beschr eibung @ 3\mod_1231771259187_ 21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 26.2 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: Busklemmen nicht auf Goldf ederkontakte legen! @ 7\mod_1266318463636_ 21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 26.3 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: ESD - Auf gute Erdung der Umgebun g achten! @ 7\mod_1266318538 667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 27 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 28 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Flac hbandkabel- und CAGE CLA MP-Anschlüsse - Überschr ift 3 @ 9\mod_128167779270 0_21.docx @ 63520 @ 3 @ 1

3.2.2 Ribbon Cable and CAGE CLAMP

Connectors

Pos: 29 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Digi taleingangskle mmen/Anschlüsse 750-1 40x 16 DI Stecker Flachbandka bel @ 3\mod_12325187938 90_21.docx @ 26474 @ @ 1

A 20-pole male connector is used to connect the field devices.

Via 2 CAGE CLAMP

connectors the field supply voltage is fed in.

Figure 3: Connectors

Table 4: Legend for Figure “Connectors”

Channel

Designation

Connector

Function

DI 1

Input DI 1: Signal voltage

DI 2

Input DI 2: Signal voltage

DI 15

Input DI 15: Signal voltage

DI 16

Input DI 16: Signal voltage

+24 V

17, 19

Field supply voltage +24 V (transmission)

0 V

18, 20

Field supply voltage 0 V (transmission)

+24 V

Field supply voltage +24 V (feed-in)

0 V

Field supply voltage 0 V (feed-in)

Pos: 30 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 31 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Anzeigeele mente - Überschrift 2 @ 4\ mod_1240984390875_21.d ocx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 32 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anzeigeelemente/ Digitaleingangsk lemmen/Anzeigeele mente 750-140x 16 DI @ 3\mod_1232459 467390_21.doc x @ 26390 @ @ 1

Figure 4: Display Elements

Table 5: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 State DI 1 1

Off

Input DI 1: Signal voltage (0)

Green

Input DI 1: Signal voltage (1)

2 State DI 2 2

Off

Input DI 2: Signal voltage (0)

Green

Input DI 2: Signal voltage (1)

15 State DI 15 15

Off

Input DI 15: Signal voltage (0)

Green

Input DI 15: Signal voltage (1)

16 State DI 16 16

Off

Input DI 16: Signal voltage (0)

Green

Input DI 16: Signal voltage (1)

Pos: 33 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Ser ien/Gerätebeschr eibung/Bedienelem ente - Überschrif t 2 @ 4\mod_1239191655456_21.d ocx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 34 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Bedienelemente/Bedi enelemente Busk lemme 750-xxxx nicht vorha nden @ 4\mod_123632203112 5_21.docx @ 28063 @ @ 1

The I/O module 750-1400 has no operating elements.

Pos: 35 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 36 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Schematisches Sc haltbild - Übersc hrift 2 @ 4\mod_1240984441 312_21.docx @ 31967 @ 2 @ 1

3.5 Schematic Diagram

Pos: 37 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Sc hematische Schaltbi lder/Digitalein gangsklemmen/Sche matisches Schaltbild 750- 14xx 16 DI HSS Stecker @ 3\mod_ 1232468043203_21.doc x @ 26433 @ @ 1

Figure 5: Schematic Diagram

Pos: 38 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Pos: 39 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Ser ien/Gerätebeschrei bung/Technisc he Daten - Überschrift 2 @ 3\ mod_1232967587687_21.doc x @ 26924 @ 2 @ 1

3.6 Technical Data

Pos: 40.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Technische Daten/ VS (Variablensteuer ung)/Technische Da ten Gerät (VS) (nur Geräte daten, keine Temperatura ngaben) @ 20\mod_141 3881815093_21.doc x @ 166173 @ 3 @ 1

3.6.1 Device

Table 6: Technical Data – Device

Width

12 mm

Height (from upper edge of 35 DIN rail)

73 mm

Depth

100 mm

Weight

50 g

Pos: 40.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Technische Daten/ VS (Variablensteuer ung)/Technische Da ten Kommunikation (VS) @ 4\ mod_1242119312796_2 1.docx @ 32970 @ 3 @ 1

3.6.2 Communication

Table 7: Technical Data – Communication

Bit width

16 bits

Pos: 40.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Technische Daten/ VS (Variablensteuer ung)/Technische Da ten Versorgung (VS) @ 4\ mod_1237879183953_21.doc x @ 28889 @ 3 @ 1

3.6.3 Supply

Table 8: Technical Data – Supply

Voltage supply

Via system supply (internal bus) and

CAGE CLAMP® connectors

Supply voltage (Uv) field supply

24 VDC (−25 % … +30 %)

Current consumption field supply

---

Current consumption system supply

Approx. 25 mA

Isolation system/supply

500 V

Pos: 40.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Technische Daten/ VS (Variablensteuer ung)/Technische Da ten Digitaleingänge (VS ) @ 4\mod_1237879070156_21. docx @ 28882 @ 3 @ 1

3.6.4 Inputs

Table 9: Technical Data – Inputs

No. of inputs

Input type

Type 1 (IEC 61131-2)

hide-side switching

Input signal “0”

DC −3 V … +5 V

Input signal “1”

DC +15 V … +30 V

Input current “0”

+0.6 mA

Input current “1”

+2.1 mA … +2.4 mA

Input filter

3.0 ms

Delay time “0” > “1”

3 ms

Delay time “1” > “0”

4 ms

Pos: 41.1 /Alle Serien (A llgemeine Module)/Ü berschriften für alle Serien/Gerätebeschr eibung/Anschluss technik - Überschri ft 3 @ 17\mod_1380123271324_21. docx @ 132788 @ 3 @ 1

3.6.5 Connection Type

Pos: 41.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Technische Daten/ Technische Daten Verdr ahtungsebene CC - 0, 08 bis 2,5mm2 @ 17\mod_138012123 8809_21.docx @ 132780 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-1400 16DI 24V DC 3.0ms, ribbon cable

Manual

Version 1.2.0

Table 10: Technical Data – Field Wiring

Wire connection

CAGE CLAMP

Cross section

0.08 mm² … 2.5 mm², AWG 28 … 14

Stripped lengths

8 mm … 9 mm / 0.33 in

Pos: 41.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Technische Daten/ Anschlusstechnik/ Technische Daten Flac hbandkabel-Ansc hluss @ 21\mod_1414513076405 _21.docx @ 166731 @ @ 1

Table 11: Technical Data – Connection of Ribbon Cable

Connection of ribbon cable

20-pole male connector

Pos: 41.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Technische Daten/Ansch lusstechnik/Techni sche Daten Datenkonta kte @ 17\mod_13801234958 44_21.docx @ 132794 @ @ 1

Table 12: Technical Data – Data Contacts

Data contacts

Slide contact, hard gold plated, self-

cleaning

Pos: 42 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Technische Daten/K limatische Umgebungs bedingungen/Techni sche Daten Klimat. Umg ebungsbed. ohne erw. Temp. 0...55°C/-25. ..+85°C @ 5\mod_1247657968 368_21.docx @ 37603 @ 3 @ 1

3.6.6 Climatic Environmental Conditions

Table 13: Technical Data – Climatic Environmental Conditions

Operating temperature range

0 °C … 55 °C

Storage temperature range

−25 °C … +85 °C

Relative humidity without condensation

Max. 95 %

Resistance to harmful substances

Acc. to IEC 60068-2-42 and

IEC 60068-2-43

Maximum pollutant concentration at