WAGO 4-channel, 24VDC, 3.0ms User manual

Brand: WAGO

Model: 4-channel, 24VDC, 3.0ms

Type: User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Fr ontseite 2015 - mit DocVariab len (Standard) @ 9\mod_1285 229289866_0.doc x @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

750-432

4DI 24V DC 3.0ms/2-

conductor

4-Channel Digital Input Module 24 V DC, 2-cond

uctor

connection; high-

side switching

Version 1.2.0

Pos: 3 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/I mpressum für Standar dhandbücher - allg. Angaben, Anschrif ten, Telefonnummern und E-Mai l-Adress en @ 3\mod_1219151118203_21. docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Liste für Textmarke Einband_vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhaltsverzei chnis - Überschrif t oG und Verzeichnis @ 3\mod_1219 151230875_21.doc x @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 15

3.2 Connectors ............................................................................................... 16

3.2.1 Data Contacts/Internal Bus ................................................................. 16

3.2.2 Power Jumper Contacts/Field Supply ................................................ 17

3.2.3 CAGE CLAMP

Connectors ............................................................. 19

3.3 Display Elements .................................................................................... 20

3.4 Schematic Diagram ................................................................................. 21

3.5 Technical Data ........................................................................................ 22

3.5.1 Device data ......................................................................................... 22

3.5.2 Supply ................................................................................................. 22

3.5.3 Communication .................................................................................. 22

3.5.4 Inputs .................................................................................................. 22

3.5.5 Connection Type ................................................................................ 23

3.5.6 Climatic Environmental Conditions ................................................... 23

3.6 Approvals ................................................................................................ 24

3.7 Standards and Guidelines ........................................................................ 26

4 Process Image ............................................................................................. 27

5 Mounting ..................................................................................................... 28

5.1 Mounting Sequence ................................................................................. 28

5.2 Inserting and Removing Devices ............................................................ 29

5.2.1 Inserting the I/O Module .................................................................... 29

5.2.2 Removing the I/O Module .................................................................. 30

6 Connect Devices ......................................................................................... 31

6.1 Connecting a Conductor to the CAGE CLAMP

................................... 31

6.2 Connection Example ............................................................................... 32

7 Use in Hazardous Environments .............................................................. 33

7.1 Marking Configuration Examples ........................................................... 34

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 34

7.1.2 Marking for America According to NEC 500 .................................... 39

4 Table of Contents WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

7.2 Installation Regulations ........................................................................... 40

7.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 41

7.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 42

7.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)43

7.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 44

7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 45

List of Figures ...................................................................................................... 46

List of Tables ........................................................................................................ 47

=== Ende der Liste für Textmarke Verzeichnis_ vorne ===

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften für alle Ser ien/Hinweise zur Doku mentation/Hinwei se zu dieser Dokumentati on - Überschrif t 1 @ 4\mod_1237987661750_21.doc x @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Hinweise/Hinwei s: Dokumentation aufbe wahren @ 4\mod_1237987 339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften für alle Seri en/Hinweise zur Dokume ntation/Gültigkei tsbereich - Übersc hrift 2 @ 12\mod_1338912448776_ 21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Gültigkeitsber eich/Gültigkeit sbereich Dokumenta tion Busklemme 750-xxxx, ohne Variantenangabe @ 14\ mod_1358944037947_2 1.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-432

(4DI 24V DC 3.0ms/2-conductor).

Pos: 11 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumenta tion/Hinweise/Acht ung: Hinweis zur Dokume ntation Busklemmen 750- xxxx @ 4\mod_1237986979 656_21.docx @ 29023 @ @ 1

The I/O module 750-432 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentatio n/Urheberschut z ausführlich @ 4\mod_123 5565145234_21.doc x @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 12.3 /Alle Serien (A llgemeine Module)/Ü berschriften für alle Serien/Hinweise zur Dok umentation/Symbo le - Überschrift 2 @ 13\ mod_1351068042408_21.doc x @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12.4.1 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden a llgemein_ - Erläuterung @ 13\ mod_1343309450020_ 21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.2 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden dur ch elektrischen Stro m_ - Erläuterung @ 13\mod_134 3309694914_21.doc x @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.3 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Warnung/Warnung: _Warnung vor Personenschäd en allgemein_ - Erläuter ung @ 13\mod_134330987704 1_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12.4.4 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Vorsicht/Vorsi cht: _Warnung vor Personen schäden allgemein_ - Erläuterung @ 13\mod_1343310 028762_21.doc x @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12.4.5 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden al lgemein_ - Erläuteru ng @ 13\mod_1343310134623_21. docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.6 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden dur ch elektrostatische Auf ladung_ - Erläuter ung @ 13\mod_13433102277 02_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.7 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweis e/Hinweis/Hinweis: _W ichtiger Hinweis al lgemein_ - Erläuterun g @ 13\mod_1343310326906_21. docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12.4.8 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Information/I nformation: _Wei tere Information allgemein_ - Erläuterung @ 13\mod_134 3310439814_21.doc x @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 12.6 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Darstellung der Zahlensysteme - Übersc hrift 2 und Inhalt @ 3\mod_122 1059454015_21.doc x @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12.7 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentatio n/Schriftkon ventionen - Überschri ft 2 und Inhalt @ 3\mod_122105952143 7_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Wichtige Erläu terungen/Wichti ge Erläuterungen - Übersc hrift 1 @ 4\mod_1241428899156_ 21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Wichtige Erläut erungen - Einleitun g @ 3\mod_1221059818031_21. docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /Alle Serien (A llgemeine Module)/Ü berschriften für alle Serien/Wichtige Er läuterungenRechtlic he Grundlagen - Übersc hrift 2 @ 3\mod_12210606263 43_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Änderungsvorb ehalt - Überschrif t 3 und Inhalt @ 3\mod_12210600364 84_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Personalqua lifikationPerson alqualifikation 750- xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240612080 46_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Bestimmungsge mäße VerwendungBes timmungsgemäße Verwendun g 750-xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Technischer Zusta nd der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_12210 60446109_21.docx @ 217 23 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 15.8 /Alle Serien ( Allgemeine Module)/Ü berschriften für alle Serien/Wichtige Er läuterungenSicher heitshinweise - Übersc hrift 2 @ 6\mod_1260180299987 _21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /Alle Serien (A llgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheitshi nweise/Einleitung Si cherheitshin weise Hardware @ 6\mod_1260 180170493_21.doc x @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.10.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Nicht an Gerä ten unter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hin weise/Gefahr/Gefahr: Einbau 0750-xxxx nur in Gehäusen, Schränken oder elektrischen Betri ebsräumen! @ 6\mod_126018 0556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.10.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Unfallver hütungsvorschr iften beachten! @ 6\mod_1260 180657000_21.doc x @ 46735 @ @ 1

Pos: 15.10.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr /Gefahr: Auf normgerec hten Anschluss achten! @ 6\mod_1260180753479_ 21.docx @ 46739 @ @ 1

Pos: 15.11.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte aust auschen! @ 6\mod_126018 0857358_21.doc x @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.11.2 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Geräte vor kriechenden und isolier enden Stoffen schütze n! @ 6\mod_126018103621 6_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.11.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Reinigung nur mit zulässigen Materi alien! @ 6\mod_12601812 03293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.11.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Kein Kontak tspray verwenden! @ 6\ mod_1260181290808_21. docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.11.5 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Verpolun g vermeiden! @ 6\mod_1260184 045744_21.doc x @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.11.6 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Elektrosta tische Entladung ver meiden! @ 6\mod_1260181 364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Gerätebeschr eibung - Überschr ift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/An wendung/DI/Anwendung 7 50-x4x x DI @ 3\mod_12 33762736718_21.doc x @ 27108 @ @ 1

The digital input module 750-432 (4DI 24V DC 3.0ms/2-conductor) receives

control signals from digital field (e.g. of sensors, transmitters, switches or

proximity switches).

Pos: 18.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-04xx 4 DI 2-Leiter ( DI und 24 V) @ 5\mod_1245910870125_21. docx @ 36002 @ @ 1

The I/O module has 4 input channels, providing a direct connection to 2-wire

sensors.

The sensors are connected to the following CAGE CLAMP

terminals: DI 1 and

24 V ... DI 4 and 24 V.

Pos: 18.3 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Hinweis/Hinweis: DI Potentialvervi elfältigungsmodu le für Sensorversorgung ei nsetzen @ 3\mod_1233762 069125_21.docx @ 27105 @ @ 1

Use field side connection modules!

Where required, use the appropriate field side connection modules for power

supply to the sensors.

Pos: 18.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/A llgemein/Verweis auf Kapitel "Anschlüsse" @ 8\mod_1276775378035_21. docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/A llgemein/Verweis auf Kapitel "Geräte ansc hließen" > "Anschluss beispiel(e)" @ 5\mod_1 246015203281_21.doc x @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 18.6 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-x4xx DI RC-Filter 3, 0 ms @ 3\mod_1233755071062_21.doc x @ 27080 @ @ 1

Each input channel has a RC noise rejection filter with a time constant of 3.0 ms.

Pos: 18.7 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/DI /I/O-Beschrei bung 750-x4xx DI HSS / positi vschaltend (24 V) @ 3\mod_123383 1724648_21.doc x @ 27231 @ @ 1

The I/O module inputs provide high-side switching. If the 24 V potential for field

power is switched to an input connection, the signal status for the corresponding

input channel is set to “high”.

Pos: 18.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/LED-Anzei ge/LED Zustand Signa l @ 3\mod_1233755258578_ 21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 18.9 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/LE D-Anzeige/Verwei s auf Kapitel "Anzeigee lemente" @ 5\mod_12460105 25000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.10 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Versorgun g 24 V, 0 V über Leistungsko ntakte Standard @ 3\mod_122 6498974531_21.doc x @ 25020 @ @ 1

The I/O module 750-432 (4DI 24V DC 3.0ms/2-conductor) receives the 24 V

voltage supply for the field level from an upstream I/O module or from the

fieldbus coupler/controller via blade-formed power jumper contacts. It then

provides these potentials to subsequent I/O modules via spring-formed power

jumper contacts.

Pos: 18.11 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicher heits- und sonstige Hinweis e/Achtung/Achtung: Maximaler Strom Leistu ngskontakte 10 A @ 3\mod_122649 9143500_21.doc x @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.12 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicher heits- und sonstige Hinweis e/Hinweis/Hinweis: Potentialeinsp eiseklemme für Er de einsetzen! (keine LK für Erde) @ 3\mod_1226499037468_2 1.docx @ 25023 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.13 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Galvanisc he Trennung Feld/Syst em @ 3\mod_1233756478 750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 18.14 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Anordn ung unter Berücksichti gung der Leistungskon takte beliebig @ 3\mod_12 33756233468_21.doc x @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.15 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ Einsatzbereich/ Einsatzbereich 750- xxxx alle Koppler/Con troller ohne Einschr änkung @ 3\mod_123254169190 6_21.docx @ 26522 @ @ 1

The I/O module 750-432 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 19 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 20 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Ansicht - Übersc hrift 2 @ 4\mod_12409842173 43_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 21 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Digital eingangsklemmen/ Ansicht 750-0432 @ 9\mod_129716 0096160_21.docx @ 69244 @ @ 1

Figure 1: View

Pos: 22 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Ansic ht CageClamp®_Legende mi t LEDs, mit 1 Entriegelungs lasche @ 15\mod_1370867 188922_21.doc x @ 122225 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with Mini-

WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

CAGE CLAMP

connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 23 /Dokumentation al lgemein/Glieder ungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 24 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Anschlüsse - Überschrift 2 @ 4\mod_1240984 262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 25 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Da tenkontakte/Klem menbus - Überschrif t 3 @ 6\mod_1256294684083_21.d ocx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 26.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Datenk ontakte - Feldbuskopp ler/-controller , Abbildung und Beschr eibung @ 3\mod_1231771259187_ 21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 26.2 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: Busklemmen nicht auf Goldf ederkontakte legen! @ 7\mod_1266318463636_ 21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 26.3 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: ESD - Auf gute Erdung der Umgebun g achten! @ 7\mod_1266318538 667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 27 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 28 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Leis tungskontakte/Fe ldversorgung - Über schrift 3 @ 6\mod_1256294 692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 29.1 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Vorsicht/Vorsic ht: Verletzungsgef ahr durch scharf kantige Messerkontakte! @ 6\ mod_1256193279401_ 21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 29.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 2 LK (Mes ser/Leistungskon takte 2 LK (Messer/Feder ) - Einleitung @ 15\mod_1371 721641099_21.doc x @ 123714 @ @ 1

The I/O module 750-432 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 29.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 2 LK (Mes ser/Leistungskon takte 2 LK (Messer/Feder ) - Abbildung, einfac he Breite - Standard @ 15\mod_13675 00700037_21.doc x @ 118396 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 29.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Leistun gskontakte 2 LK (Messer/ Leistungskontakt e 2 LK (Messer/Feder) - Legende @ 15\mod_1371721352500 _21.docx @ 123710 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 29.5 /Serie 750 ( WAGO-I/O-SYSTEM)/ Wichtige Erläuterungen/ Sicherheits- und s onstige Hinweise/Ac htung/Achtung: Maxima ler Strom Leistungsko ntakte 10 A @ 3\mod_12264991435 00_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 29.6 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sonstige Hinweise/ Hinweis/Hinweis: Potentialeinspei seklemme für Erde einsetz en! (keine LK für Er de) @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 30 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 31 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/CAGE CLA MP-Anschlüsse - Übersc hrift 3 @ 6\mod_1256296337770 _21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

Connectors

Pos: 32 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Digi taleingangsklem men/Anschlüsse 750-04xx 4 DI 2-Leiter direkt (DIn, 24 V) @ 9\mod_129717150760 1_21.docx @ 69336 @ @ 1

Figure 4: CAGE CLAMP

Connectors

Table 5: Legend for Figure “CAGE CLAMP

Connectors”

Channel

Designation

Connector

Function

DI 1

Input DI 1: Signal voltage

24 V

Sensor supply 24 V

DI 2

Input DI 2: Signal voltage

24 V

Sensor supply 24 V

DI 3

Input DI 3: Signal voltage

24 V

Sensor supply 24 V

DI 4

Input DI 4: Signal voltage

24 V

Sensor supply 24 V

Pos: 33 /Serie 750 (W AGO-I/O-SYSTEM)/W ichtige Erläuterungen/Si cherheits- und sons tige Hinweise/Hin weis/Hinweis: DI Potenti alvervielfältigu ngsmodule für Sensor versorgung einsetz en @ 3\mod_1233762069125_ 21.docx @ 27105 @ @ 1

Use field side connection modules!

Where required, use the appropriate field side connection modules for power

supply to the sensors.

Pos: 34 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-432 4DI 24V DC 3.0ms/2-conductor

Manual

Version 1.2.0

Pos: 35 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Seri en/Gerätebeschrei bung/Anzeigee lemente - Überschrift 2 @ 4\ mod_1240984390875_21.d ocx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 36 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anzeigeelement e/Digitaleingangsk lemmen/Anzeigee lemente 750-04xx 4 DI (Agn, Bgn, Cgn, Dgn) @ 9\mod_1291641 003036_21.doc x @ 67080 @ @ 1

Figure 5: Display Elements

Table 6: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Status DI 1 A

Off

Input DI 1: Signal voltage “0”

Green

Input DI 1: Signal voltage “1”