Installation Instructions for Clareo Surface
Models CLS-XX & CLQ-XX
REV0.0 03062019*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Instruction page index:
Page 1 of 7
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
Clip-in installation
Screw-in installation
Magnetic installation
Adjustable hinge mounting installation
T-bar clip mounting installation
Power feed layout guide
2
3
4
5
6
7
Clareo Surface with adjustable hinge mounting
Clareo Surface with screw-in mount clip
Clareo Surface with clip-in mount
or Clareo Surface magnetic
Clareo Surface with t-bar mounting clips
Clareo Surface - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
Models CLS-XX & CLQ-XX
Page 2 of 7
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
4.1 Connect +24 VDC red wire from the fixture to the power supply
+24 VDC red wire with a wire nut. Connect -24VDC black wire
from the fixture to power supply -24VDC black wire with a wire
nut.
4
class II
power
supply
24 VDC
120 VAC
4.1
to fixture
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
Note: Refer to the power supply installation instruction for
additional information.
Note: More than one person is recommended for this
installation.
1
1.1 Carefully remove the clip-in channel from the back of the
fixture. Clip-in channel is 1/2" shorter than the fixture for
wire management.
2.1 Determine the location of the fixture. Then secure the clip-in
channel to the surface with the provided mounting screws. When
installing the clip-in channel take into consideration the 1/2"
shorter per wire lead/connector.
2.2 Install mounting screws every 6 inches to the center of the mounting
channel.
1.1
2
fixture
lead wires
screw
clip-in channel
2.1
screw
3
Option 2- Feed wire whip to the power supply.
OR
3.1 Follow connector dimensions below and drill hole through surface.
Insert wire lead/connector through surface & snap fixture into the
mounting channel to secure in place. Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
3.2 Follow one of the two options to connect the fixture to the
power supply.
female quick
connect
male quick
connect
to power supply
fixture
wires from
fixture
wires from
fixture
3.1
3.2
3.2
Female quick
connect end
0.45"
Male quick
connect end
0.38"
Female/male
adapter
0.45"
Lead wire
end
0.20"
E472444
Clip-in installation
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE REV0.0 03062019
clip-in channel
clip-in channel
Please read all instructions prior to installation and keep for future reference!
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Page 3 of 7
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
2
2.1 Determine the location of the fixture. Then secure the fixture to the surface
using the provided mounting screws.
3
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
3.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
fixture
fixture
screw
4.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
4
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
4.1
to fixture
wires from
fixture
E472444
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
2.1
2.1
1
1.1 Install the screw-in brackets 4” from each end and 30” in between the fixtures. Line up each screw-in
bracket to the back on the fixture & insert the edge of the clip into the fixture. Then rotate and push bracket
in until you feel a click. Followed by tightening the set screw using the Allen wrench (provided). Repeat for
the remaining brackets.
1.1
1.1 1.1
completely installed
fixture
screw-in
bracket
set screw
screw-in bracket
Screw-in installation
REV0.0 03062019
Clareo Surface - Installation Instructions
Models CLS-XX & CLQ-XX
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
1
1.1 Determine the location of the fixture. Must be made of steel or a ferrous
metal. Clean the surface area thoroughly from any debris. Snap the fixture
onto the metal surface. If necessary fixture can easily be removed by
rotating off the surface and repositioning correctly.
fixture
fixture
3.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
3
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
3.1
to fixture
2
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
2.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
wires from
fixture
metal backing
metal backing
1.1
1.1
Magnetic installation
Please read all instructions prior to installation and keep for future reference!
Page 4 of 7
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
REV0.0 03062019
Clareo Surface - Installation Instructions
Models CLS-XX & CLQ-XX
Please read all instructions prior to installation and keep for future reference!
Page 5 of 7
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SURFACE MOUNT ONLY
5. SUITABLE FOR WET LOCATIONS, MUST USE APPROPRIATE
WEATHERPROOF RATED WIRE CONNECTORS.
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
Adjustable hinge installation
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
1
1.1 Slightly loosen both screws on the sides of the hinge bracket.
Rotate the fixture to expose mounting hole.
mounting bracket
mounting
bracket
fixture mounting
hole
2
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
2.1 Determine the location of the fixture. Then secure the fixture to
the surface using the provided mounting screws.
2.2 Rotate the fixture to the desired angle then tighten the side
screws to secure.
1.1
2.1
2.1
4.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
4
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
4.1
to fixture
screw
2
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
2.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
wires from
fixture
1.1
REV0.0 03062019
Clareo Surface - Installation Instructions
Models CLS-XX & CLQ-XX
Please read all instructions prior to installation and keep for future reference!
Page 6 of 7
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SURFACE MOUNT ONLY
5. SUITABLE FOR WET LOCATIONS, MUST USE APPROPRIATE
WEATHERPROOF RATED WIRE CONNECTORS.
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE REV0.0 03062019
Clareo Surface - Installation Instructions
Models CLS-XX & CLQ-XX
1
1.1 Align the fixture t-bar clips to the track. Followed by rotating, then
snapping the t-bar clips into the track to secure in place.
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
3.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
3
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
3.1
to fixture
2
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
2.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
wires from
fixture
T-Bar clip installation
fixture
t-bar clip
1.1
1.1
Rotate to
secure
in place
t-bar clip
track
Please read all instructions prior to installation and keep for future reference!
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Page 7 of 7
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
power supplies at the
end of the run
power supplies in the
middle of the run
consecutive layout,
NOT RECOMMENDED
multiple powerfeed layouts
power supply
low voltage wires
fixture 1
fixture 1 fixture 2
low voltage wires
power supply
power supply
low voltage wires
fixture 1
power supply
low voltage wires
fixture 2
REV0.0 03062019
Clareo Surface - Installation Instructions
Models CLS-XX & CLQ-XX
/
