2. luminii
  3. Kendo M Graze Wet

luminii Kendo M Graze Wet Installation guide

  • Hello! I've reviewed the installation instructions for the Luminii KMW- and KSW- light fixtures. This document provides guidance on how to properly mount the fixtures, connect them to a power supply, and ensures they're safe for use in wet locations and closet spaces. The instructions detail the need for a qualified electrician, use of a Class 2 power unit, and specific wiring connections. I am ready to answer your questions about these light fixtures.
  • Who should install this product?
    What type of power unit should be used?
    What is the voltage of this product?
    Can this product be installed in wet locations?
4.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
Kendo M & S Wet - Installation Instructions for wet locations
REV1.9
Please read all instructions prior to installation and keep for future reference!
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
1
Models KMW-, KSW-
22.2 Follow one of the two options to connect the fixture to the
power supply.
Option 2- Feed wire leads to the power supply.
OR
wire leads
light fixture
male quick
connect
female quick connect
4
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
Page 1 of 2
1.1 Determine the location of where the fixture(s) will be installed. Lay the fixture(s) on the surface, and make reference marks for the mounting brackets.
Make marks 4" from each end of the fixture(s) and also every 30" in between. (20" if using magnetic mounting clips)
1.2 Lay the fixed or adjustable mounting bracket (depends on model ordered) onto the mark points and secure using the provided hardware.
If mounting to concrete, solid block, or brick we recommended using McMaster-Carr anchor part# 97065A100 & screw part# 90198A110.
4"
fixture
mark
4"
1.1
surface
2.1 Snap fixture into the brackets to secure in place.
2.2
2.2
4.1
to fixture
to power supply
to power supply
E472444
1.2
flathead screw
fixed mounting bracket
2.1
fixture
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
30"
(20" for magnetic clip) OR adjustable
mounting
bracket
adjustable
mounting
bracket
3.1 If applicable, slightly loosen screw on
adjustable mounting bracket and adjust up to
180° and then re-tighten screw to secure
position.
3
3.1
180°
screw
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SURFACE MOUNT ONLY
5. SUITABLE FOR WET LOCATIONS, MUST USE APPROPRIATE
WEATHERPROOF RATED WIRE CONNECTORS.
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
8. TYPE IC
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
5Kendo sample layout
fixture
fixture
to power supply
male quick
connect
female quick
connect
Page 2 of 2
5.1
fixed mounting
bracket
adjustable
mounting bracket
Please read all instructions prior to installation and keep for future reference!
Kendo M & S Wet - Installation Instructions for wet locations
Models KMW-, KSW-
E472444
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
REV1.9
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SURFACE MOUNT ONLY
5. SUITABLE FOR WET LOCATIONS, MUST USE APPROPRIATE
WEATHERPROOF RATED WIRE CONNECTORS.
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
8. TYPE IC
/