*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
3
Kilo GW- Installation Instructions
Models KGW-
Adjustable bracket
back-mount
Adjustable bracket
side-mount
1.1 Determine the location of the install. Use the pre-installed mounting bracket holes as a guide , then mark the desired location. If using adjustable
mounting brackets, side screws must be loosen to rotate.
Refer to specific
mounting bracket for details
direction
of light
130° 130°
direction
of light
side screw side screw
1.2 Align the mounting bracket holes to the marked
locations on the surface, and secure by using the
provided screws. If using the adjustable mounting
brackets rotate to the desired position and tighten
the side screws to secure.
1.3 After the installation is complete remove the protective film from
the front of the lens.
Fixed mounting
bracket
Kilo GW
adjustable mounting
bracket screw
protective film
1.1
1.2
1.3
female quick
connect
male quick
connect
to power supply
Kilo GW
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect wire through
conduit to power supply.
2.1 Follow one of the two options to connect the Kilo GW
to the power supply.
Kilo GW
wire leads
to power supply
Option 2- Feed wire whip to the power supply.
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
3.1
to fixture
3.1 Connect +24 VDC red wire from the fixture to the power supply +24V DC red wire with a wire nut. Connect -24V DC black wire
from the fixture to power supply -24V DC black wire with a wire nut.
2.1
2.1
class II power supply
screw
fixed bracket
Kilo GW
1.2
1
2
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED Page 1 of 3
E472444
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV 4.3
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Kilo GW- Installation Instructions
Models KGW-
4Kilo GW sample layout
Female and male connector ends of
Y-splitter connects to Kilo GW light
fixture by carefully pushing into Kilo
GW light fixture connector ends.
linking cable types
12.00 part # LC-12
48.00 part # LC-48
120.00 part # LC-120
female
connector end
Y-splitter
part # LYC
male connector end
female
connector end
female/male
adapter part# FMA
female connector end
Use female/male adapter part
#FMA in installations where two
female connector ends need to be
mated together.
Kilo GW
to power supply
Kilo GW
Kilo GW
Kilo GW
Kilo GW Kilo GW
4.1
4.1
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED
REV 4.3
Page 2 of 3
E472444
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Kilo GW- Installation Instructions
Models KGW-
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. TYPE IC
8. INHERENTLY PROTECTED Page 3 of 3
E472444
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV 4.3
power supplies at the
end of the run
power supplies in the
middle of the run
consecutive layout,
NOT RECOMMENDED
multiple powerfeed layouts
power supply
low voltage wires
fixture 1
fixture 1 fixture 2
low voltage wires
power supply
power supply
low voltage wires
fixture 1
power supply
low voltage wires
fixture 2
/