Midmark Elevance® Standard Delivery System Installation guide

1

TP201 20-42-FO-00013 Rev A1 C2169

Applies to Models:

153800 (-001 thru -003)

Special Tools:

none

Language of origin: English

Note

Use this kit to replace the Electronic Proportional Water Valve, for all Elevance

®

Standard and Continental-Style Delivery Units.

Electronic Proportional Water Valve Installation

[Kit # 002-2029-00]

003-2913-00 Rev. A (mm/yy)

Tray

Pad

Magnetic Lid

Metal Cover

Top Cover

Assembly

Screws (8)

Water

Shut Off

Air

Shut Off

Unplug Power

Supply

Water

Bottle

J-Box

WARNING

Always disconnect power from the chair / unit before removing any covers.

Failure to do so may result in personal injury.

Accessing the Proportional Water Valve on an Elevance

®

Standard Unit...

A) Turn off air and water using the Shut Offs in the J-Box.

B) Unplug Power Supply from electrical mains in the J-Box.

C) Turn Water Bottle CCW to release the air pressure in the water tubing.

D) Remove, Tray, Pad, and Magnetic Lid.

E) Remove two screws and lift off the Metal Cover.

F) Remove handpieces from holders (allow them to hang) and remove eight

screws so you can rotate the Top Cover Assembly upside down on top

of the instrument platform (leaving handpieces, tubing and wiring connected).

G) Disconnect the handpiece sensor harnesses, touch sensor harnesses, USB and

LIN connections from the ICM PC Board and remove the Top Cover Assembly.

ICM

PC Board

Elevance

®

Standard Unit

midmark.com

Style G

2

003-2913-00

TP201 20-42-FO-00013 Rev A1 C2169

Pivot Tower

Assembly

Metal Cover

Top Cover

Assembly

Screws (8)

Arm

WARNING

Always disconnect power from the chair / unit before removing any covers.

Failure to do so may result in personal injury.

Accessing the Proportional Water Valve on an Elevance

®

Continental-Style Unit...

A) See A) through C) on page 1 to turn off power and relieve pressure in tubing.

B) Move handpieces to the back of the unit (allow them to hang freely, not shown).

C) Push arm forward to access screw, remove it and pull up to remove the arm. Remove all arms.

D) Remove Magnetic Lid.

E) Remove two screws and lift off the Metal Cover.

F) Remove eight screws, then lift and rotate the Top Cover Assembly forward.

G) Unplug all Sensory Input connectors, the LIN connector, USB cables and the Interface Board ribbon

cable from the ICM PC Board. Move Top Cover Assembly aside. (Tubing will still be connected.)

H) Remove six screws and lift off Pivot Tower Assembly to access the Interface Board.

ICM

PC Board

Elevance

®

Continental-Style

Unit

Magnetic Lid

Interface Board

midmark.com

Style G

Color Page

3

003-2913-00

TP201 20-42-FO-00013 Rev A1 C2169

BK

RD

BK

GY

PK

GY

PK

RD

BK

Remove Water Valve...

A) Unplug connector from J6 on the Interface Board.

B) Unplug connector from the Water Valve.

C) Disconnect the water IN line from the Water Valve.

D) Disconnect the water OUT line from the Water Valve.

E) Remove two screws and discard the Water Valve.

Note: The Water / Air wiring harness remains connected to the Air Valve.

Water Valve

Air Valve

Water IN

Water OUT

midmark.com

Style G

Color Page

4

003-2913-00

TP201 20-42-FO-00013 Rev A1 C2169

BK

Install Water Valve Kit....

A) Place Water Valve in unit near the Air Valve,

B) Connect the water IN line to the Water Valve.

C) Connect the water OUT line to the Water Valve.

D) Plug male connector into J6 on the Interface Board.

E) Plug female connector into the male Air / Water connector

from the Air Valve.

Note: The 3-port connector of the Water / Air wiring harness does not get

connected. Wire tie it to another wire to secure it.

Water Valve

Air Valve

Water OUT

Water IN

Water OUT

Water IN

Reconnect all Components, Return all Covers

and Power Up the Unit....

A) Reference pages 1 and 2 to reassemble and

ready the unit for operation.

midmark.com

Style G

Color Page

5

003-2913-00

TP201 20-42-FO-00013 Rev A1 C2169

Flush the Delivery Unit to Verify Operation of the

Proportional Water Valve...

A) Move the Master Switch to the ON position. Allow the Home Screen to

appear on the Integration Control Module

®

(ICM).

B) Pull all of the handpieces from the holders and disconnect them from the

tubing. The Flush Operation Screen appears on the ICM.

C) Press to highlight DAILY flush and the to select it.

D) Press to highlight HANDPIECE FLUSH.

E) Hold the handpiece tubes over a container to catch the water, then

press the to begin the flush operation. The Flush Process Screen

displays a countdown timer.

F) When Flush process is complete the Flush Operations Screen appears.

Return the handpieces to their tubes and holders, then press to

continue.

G) Highlight EXIT and press the to exit the next two Flush Operations

and return to the Home Screen.

Note: If any leaks occur during the flush, repeat the installation from the beginning to pinpoint

their location and repair them.

Handpieces

ON

G

D

C

Master

Switch

ICM

E

FE

A

midmark.com

Style G

Color Page

6

003-2913-00

TP201 20-42-FO-00013 Rev A1 C2169

This manual is available in the following languages at midmark.com/technical-library

Choose your preferred language from the drop-down box at the top of the page and

enter the part number shown below in the SEARCH box:

German: 003-2913-01

French: 003-2913-02

Italian: 003-2913-07

Spanish: 003-2913-03

midmark.com

Style G

Midmark Elevance® Standard Delivery System Installation guide

This manual is also suitable for

Midmark Elevance® Standard Delivery System Installation guide

Related papers

Other documents