Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Brand: Midmark

Model: Integra™ Operatory Cabinetry - Side Cabinetry

Type: Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions to optimize your dental operatory. Its durable construction and adjustable features, including leveling screws and cam screws, ensure precise alignment and stability. The cabinetry allows for easy integration with additional storage units and countertop installation, maximizing your workspace. With its sleek design and functional features, it enhances both the aesthetics and efficiency of your dental operatory.

™™

003-1935-00 Rev.B

30” Round Sink Unit Installation

Applies to Models:

OSC030R-R

OSC030R-L

Special Tools:

Level

1/4” deep well socket

Caulking Gun

Belt Sander

DA139400i

Models:

OSC030R-R (30” Round Sink Unit w/ or w/o Tapmaster™, RH)

OSC030R-L (30” Round Sink Unit w/ or w/o Tapmaster™, LH)

OSC030R-L (Shown)

NextNext

BackBack

Note

• All plumbing must be made by a

licensed plumbing contractor and

conform to local, city, and national

codes pertaining to the installation.

DA2221i

Waste drain

2 in (5.1 cm)

hole

1-1/2 in drain

pipe

HOT

COLD

FLOOR

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1-3/4 in (4.5 cm) Min.

3-3/4 in. (9.5 cm) Max from

finished wall surface .

Use 1/2 in male NPT fittings on end of

stubs for connections to shut-off valves.

Install 1/2 in inlet x 3/8 in O.D. outlet

angle shut-off valves.

WALL MOUNT SERVICE

16-1/4 in (41.3 cm)

3 in

7.6 cm

13-1/4 in (33.7 cm)

WALL

FLOOR MOUNT SERVICE

Waste drain 2 in

(5.1 cm) hole

1-1/2 in drain

pipe

HOT

COLD

8.75 in

22.2 cm

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1 in (2.5 cm) Min.

2-1/2 in (6.4 cm) Max from

finished floor surface.

Use 1/2 in male NPT fitting

on end of stubs for connections

to shut-off valves. Install 1/2 in

inlet x 3/8 in O.D. outlet angle

shut-off valves.

3 in

7.6 cm

RH SINK CABINET DIMENSIONS

NextNext

BackBack

Note

• All plumbing must be made by a

licensed plumbing contractor and

conform to local, city, and national

codes pertaining to the installation.

LH SINK CABINET DIMENSIONS

DA2222i

Waste drain

2 in (5.1 cm)

hole

1-1/2 in drain

pipe

HOT

COLD

FLOOR

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1-3/4 in (4.5 cm) Min.

3-3/4 in. (9.5 cm) Max from

finished wall surface .

Use 1/2 in male NPT fittings on end of

stubs for connections to shut-off valves.

Install 1/2 in inlet x 3/8 in O.D. outlet

angle shut-off valves.

WALL MOUNT SERVICE

16-1/4 in (41.3 cm)

3 in

7.6 cm

13-1/4 in (33.7 cm)

WALL

FLOOR MOUNT SERVICE

Waste drain 2 in

(5.1 cm) hole

1-1/2 in drain

pipe

HOT

COLD

8.75 in

22.2 cm

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1 in (2.5 cm) Min.

2-1/2 in (6.4 cm) Max from

finished floor surface.

Use 1/2 in male NPT fitting

on end of stubs for connections

to shut-off valves. Install 1/2 in

inlet x 3/8 in O.D. outlet angle

shut-off valves.

3 in

7.6 cm

NextNext

BackBack

DA139600i

Sink Cabinet

WALL

DESIRED POSITION OF EDGE OF UNIT

RAISE

CABINET

LOWER

CABINET

1 1/2" (max.)

(3.8 cm)

SINK BASE CABINET INSTALLATION

Equipment Alert

Do not adjust leveling screws more than

1 1/2” (3.8 cm) to prevent loss of stability.

Step 1: Remove sink bottom

from base cabinet.

Step 2: Adjust leveling screws

to fully lowered position

and move cabinet to

desired position.

Step 3: Level cabinet with

leveling screws.

NextNext

BackBack

DA2156i

DOOR ADJUSTMENT

Vertical Adjustment

A) Loosen both screws.

B) Move up or down.

C) Retighten screws.

Horizontal Adjustment

A) Turn cam screw to move

panel side to side.

Depth Adjustment

A) Turn cam screw to move

panel front to back.

NextNext

BackBack

DA139801i

Note

If necessary, sand counter top

to form to wall.

Step 1: If necessary, level and

connect any additional

storage units to Sink Unit.

Step 2: Position counter top so it

extends 3/8” (0.95 cm) to

1/2” (1.3 cm) over each

end of cabinet(s) and secure

with #10 x 5/8” screws.

Special hex bolts

(#10-24 x 3/4”)

CONNECTING ADDITIONAL UNITS

& COUNTER TOP INSTALLATION

NextNext

BackBack

DA2157i

SINK INSTALLATION &

PLUMBING CONNECTIONS

Step 1: Caulk around perimeter of

hole, then position sink.

Step 2: Secure sink with bracket kits

included with sink.

Step 3: If required, caulk

around perimeter

of hole, and install

waste ring.

Step 5: Refer to the instructions with

Tapmaster™ faucet controller

for installation procedure.

Step 4: Install faucet and soap

dispenser using instructions

included with those items.

Note

All plumbing must be made by a licensed

plumbing contractor and conform to local,

city, and national codes pertaining to the

installation.

Equipment Alert

When installing a sink, Midmark

recommends securing cabinet to wall.

Failure to comply may result in damage

to plumbing connections.

LAMINATE TOP SHOWN

NextNext

BackBack

NextNext

BackBack

Midmark Corporation

For contact information, go to:

www.midmark.com

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Related papers

Other documents