Extron TLP Pro 720C User manual

Type
User manual
TLP Pro 720C
User Guide
TouchLink
®
TouchLink Pro Touchpanel Control Systems
68-2406-01 Rev. B
01 21
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron website,
www.extron.com.
Sicherheitsanweisungen • Deutsch
WARUNG: Dieses Symbol auf demProdukt soll den Benutzer darauf
aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes
gefährliche Spannungen herrschen, die nicht isoliert sind und die einen
elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den
Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de importantes instrucciones de
uso y mantenimiento estas estan incluidas en la documentación
proporcionada con el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad de
Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec
l’équipement.
Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,
la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les
informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site
Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire
l’utente della presenza di tensione non isolata pericolosa all’interno
del contenitore del prodotto che può costituire un rischio di scosse
elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire
l’utente della presenza di importanti istruzioni di funzionamento e
manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida
alla conformità normativa e di sicurezza di Extron, cod. articolo 68-290-01, sul
sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej
zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron
bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01,
na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению
электрическим током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций по
эксплуатации и обслуживанию в руководстве, прилагаемом к
данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других вопросах
см. руководство по безопасности и соблюдению нормативных
требований Extron на сайте Extron: , www.extron.com,
номер по каталогу - 68-290-01.
Copyright
© 2014-2021 Extron. All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners..
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (
®
), registered service marks (
SM
), and trademarks (
TM
) are the property of RGBSystems, Inc. or Extron
(see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, Global
Configurator, Global Scripter, GlobalViewer, Hideaway, HyperLane, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort,
NAV, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch,
StudioStation, System I
NTEGRATOR, TeamWork, TouchLink, VideoLounge, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP
Systems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-RATE Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D Ripple
Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP
Configurator, DSVP (Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP,
MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC - QuickSwitch Front Panel Controller, Room Agent, Scope-Trigger, SIS - Simple
Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한
자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수
안내서, 68-290-01 조항을 참조하십시오.
安全说明 简体中文
警告 产品上的这个标志意在警告用, 该产品机壳内暴露的危险
电 压 ,有 触 电 危 险
注意 产品上的这个标志意在提示用户, 设备随附的用户手册中有重
要的操作和维护(维修)说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使
用的特性等相关内容,
敬请访问 Extron 网站 , www.extron.com,参见 Extron 安全规范指南,产品编号
68-290-01
安全記事 • 繁體中文
警告: 若產品上使用此符號,是為了提醒使用者產品機殼內存在未隔離的危
險電壓,可能會導致觸電之風險
注意 產品上使用此符號,是為提醒使用者設備隨附戶手冊中有重
)説
有關安全性指導方針法規遵EMI/EMF 相存取圍和關主題的詳細資訊
請瀏覽 Extron 網站www.extron.com然後參閱《Extron 安全性與法規遵
準則編號 68-290-01
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
interference. This interference must be corrected at the expense of the user.
NOTE:
This unit was tested with shielded I/O cables on the peripheral devices. Shielded
cables must be used to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide on the Extron website.
Conventions Used in this Guide
Notifications
In this user guide, the following are used:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Directory paths that do not have variables are written in the font shown here:
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the
File menu, select New.
Click the
OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at www.extron.com/technology/glossary.aspx.
Contents
Introduction............................................................ 1
About the TLP Pro 720C .................................... 1
Features ............................................................. 1
Application Diagram ........................................... 2
Requirements ..................................................... 3
Software ......................................................... 3
Hardware ........................................................ 3
Installation Overview ........................................... 4
Mounting the TLPPro720C ............................... 7
Planning ............................................................. 7
Tools Required for Installation ............................. 8
Included Parts .................................................... 8
Ensure Adequate Under-table Clearance for
Retractors ......................................................... 9
Cutting the Table ................................................ 9
Cut-out Dimensions ........................................ 9
Cutting the Surface ....................................... 10
Running Cables ............................................... 11
Installing Cable Retractors (Optional) ................ 11
Installing Power Modules (Optional) .................. 12
Preparing and Installing the AAP Assemblies .... 13
Installing AAPs .............................................. 13
Inserting the AAP Assemblies ....................... 14
Mounting the TLP Pro 720C Enclosure ............. 15
Panel Features .................................................... 16
Front Panel Features ......................................... 16
Connectors ...................................................... 18
Power Connector ......................................... 18
Network and Power over Ethernet
Connector ................................................... 20
On-screen Menus ............................................... 22
Setup Menu ...................................................... 22
Status Screen ............................................... 22
Network Screen ............................................ 23
Display Screen .............................................. 25
Audio Screen ................................................ 26
Advanced Screen ......................................... 27
Calibration Screen ............................................ 28
Configuration Software ..................................... 29
Configuration Software ..................................... 29
Installing Software ............................................ 29
Using the Software ........................................... 30
TLP Pro 720C Web Page ................................. 31
Updating the Firmware ..................................... 33
Downloading Firmware ................................. 33
Reference Material ............................................. 34
Best Practices for Cleaning Your
Extron Products ............................................... 34
Network Port Requirements and Licensed
Third-Party Software Used in
the Touchpanels .............................................. 34
Reset Modes .................................................... 35
Use Factory Firmware ................................... 35
Reset All IP Settings ..................................... 35
Reset to Factory Defaults .............................. 36
Enable or Disable the DHCP Client ............... 36
Secure Sockets Layer (SSL) Certificates ........... 37
IEEE 802.1X Certificates ................................... 37
Certificate File Requirements......................... 38
Private Key File Requirements ....................... 38
TLP Pro 720C • Contents vii
TLP Pro 720C • Contents viii
Introduction
This guide describes the function, installation, and operation of the Extron TLPPro720C
TouchLink Pro Touchpanel. Unless otherwise stated, the terms TLP Pro and touchpanel refer
to the TLP Pro 720C.
The TLP Pro 720C is ideal for any AV application requiring a full-size, Cable Cubby touchpanel
with a customizable interface.
This section provides an overview of these products:
About the TLP Pro 720C
Features
Application Diagram
Requirements
About the TLP Pro 720C
The Extron TLP Pro 720C is a Cable Cubby touchpanel with a flip-up, 7-inch 800x480
(WVGA), LCD touchscreen with 18-bit color depth. It
combines the AV system control
of TLPPro720Series touchpanels with the cable management convenience of the
CableCubby. It features a tilt-up, full-color touchscreen in an elegant, metal enclosure that
can be mounted securely into a tabletop, lectern, or other flat surface.
The user can define the graphics and the functions associated with those graphics, providing
versatility and adaptability to the configuration and control of an AV system. The screen layout
is designed with the Extron GUI Designer software. The functions can be assigned to the
screen objects with the Extron Global Configurator Plus and Global Configurator Professional
configuration software or with Global Scripter programming software.
A motion sensor, light sensor, and a speaker provide sleep mode, auto dimming, and audible
feedback respectively.
Features
7-inch flip-up LCD touchscreen — With 800x480 resolution and 18-bit color depth.
Faster processing and more memory — Allows for quicker configuration uploads and more
storage for GUI pages.
Compatible with the full range of Extron IPL Pro and IPCP Pro control processors
Allows easy integration into existing systems.
Power over Ethernet (PoE 802.3af, Class3) compliance
Allows the touchpanel to
receive power and control over a single Ethernet cable, eliminating the need for a local
power supply. The PoE injector is sold separately.
Built-in speaker — Mounted in the Cable Cubby compartment, with improved audio
performance provide audible feedback from button presses.
Light sensor — Adjusts screen brightness as the ambient room lighting changes.
Cable Cubby design — Offers easy access to AV, data, and power connections. AC power
modules are available for US, Europe, and other major world markets. AV connectivity options
include:
Up to 11 single-space AAP-Architectural Adapter Plates.
Up to 6 Retractor Cable Retraction Systems.
TLP Pro 720C • Introduction 1
Convenient LED lighting — Illuminates power and AV Cable Cubby area.
Integrated lid switch — Automatically wakes the touchpanel when opened and can trigger
any other system function.
System connection status indicator — Provides visual feedback if the touchpanel is not
communicating with a control processor.
Automatic clock synchronization — Allows touchpanel to display the accurate time and
date.
Adjustable sleep timer — Puts touchpanel into sleep mode.
Fully customizable using Extron control system software — GUI Designer combined
with Global Configurator Plus, Global Configurator Professional, or Global Scripter.
Supports Extron Control App and Extron Control for Web.
JITC Certified — Successfully completed interoperability and information assurance testing
for use in government applications and other mission-critical environments.
Installation routing template is available.
Highly reliable, energy-efficient external universal power supply optional — Provides
worldwide power compatibility, with high demonstrated reliability and low power consumption
for reduced operating costs.
Application Diagram
This diagram shows a typical application for the TLP Pro 720C touchpanel.
POWER
12V
--A MAX
G
Tx Rx RTSCTS
COM 1
G
Tx Rx
COM 2
VCG
VOL
RELAYS
1 2 C
1 2 3 4 G
DIGITAL I/O
PWR OUT= 6W
eBUS
+V +S
-S
G
LAN
IPCP PRO 250
IR/S
S G
SIGNAL
INPUT
CONFIG
HDCP
2-CH PCM
BITSTREAM
SIGNAL
OUTPUT
HDCP
ANALOG
S/PDIF
HAE 100
HDMI AUDIO EXTRACTOR
RGB - HDMI 300 A
MENU ENTER
ADJUST
CONFIG
RGB - HDMI 300 A
MENU ENTER
ADJUST
CONFIG
RGB - HDMI 300 A
MENU ENTER
ADJUST
CONFIG
DXP SERIES
DIGITAL CROSSPOINT MATRIX SWITCHER
C O N T R O L I/O
CONFIG
1
2
3
4
5
6
7 8
OUTPUTS
1
2
3
4
5
6 7
8
INPUTS
ENTERPRESET
VIEW ESC
VIDEOAUDIO
PUSH PUSH
POWERGUIDE MENU RES480 480p 720p 1080i 1080p
DIRECTV HD
SELECT
DIRECTV
BASSLEVELTREBLE
MINI POWER AMPLIFIER
MPA 152 Plus
STEREO
DUAL
MONO
Extron
Help
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
1 2 3
VCRLaptop PC DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
321
654
987
Enter
0
Ethernet
Satellite Receiver
TCP/IP
Network
Extron
TLP Pro 720C
7" Cable Cubby
TouchLink Pro Touchpanel
Extron
IPCP Pro 250
IP Link Pro
Control
Processor
IR
Ethernet
Ethernet
Ethernet/PoE
RS-232
RS-232
Extron DXP 84 HDMI
HDMI Matrix
Switcher
Volume Control
Extron MPA 152 Plus
Power Amplier
Video
Video
PC
Blu-ray Player
Laptop
Flat Panel Displays
Audio/VideoAudio/Video
Audio
Extron
RGB-HDMI 300 A
RGB to HDMI Scaler
Video
Laptop
Audio/Video
Audio
Audio
Audio/VideoAudio/Video
Video
Audio/Video
Audio
Audio
Video
Extron SI 26CT
Two-Way Ceiling Speakers
Extron HAE 100
HDMI Audio
Extractor
Extron
RGB-HDMI 300 A
RGB to HDMI Scaler
Extron
RGB-HDMI 300 A
RGB to HDMI Scaler
Figure 1. Application Diagram
TLP Pro 720C • Introduction 2
Requirements
Software
For a complete list of the requirements for running GUI Designer, Global Configurator Plus and
Professional, Global Scripter, and Toolbelt see the Extron web page (www.extron.com) for that
software.
NOTE: These touchpanels are not compatible with GlobalConfigurator 3 or
GUIConfigurator.
Hardware
An Extron IP Link Pro control interface must also be connected to the same network domain
as the TLP Pro TouchLink panel. See www.extron.com for a list of suitable controller processor.
NOTE: These touchpanels are not compatible with Extron IP Link (non-Pro) control
processors.
TLP Pro 720C • Introduction 3
Installation
Overview
This section provides an overview of the installation process. Follow the links for a more
detailed explanation of each step.
1. Before starting, download and install the latest versions of the following software:
Global Configurator Professional or Global Configurator Plus — For setting up
and configuring the control processor and touchpanel.
GUI Designer — For designing layouts for Extron TouchLink Pro touchpanels and
third party touch interfaces.
Global Scripter — Provides an integrated development environment for Extron
control systems programming.
Toolbelt — Provides device discovery, device information, firmware updates,
and configuration of network settings, system utilities, and user management for
TouchLinkPro devices.
All four programs can be downloaded from www.extron.com (for information about using
the software, see Configuration Software (see page 29).
2. Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you will also require
IP address
Subnet mask
Gateway
Username — by default these are either admin or user.
Passwords — The factory configured passwords for all accounts on this device
have been set to the device serial number. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password changes to the
default password. The default password is extron (for either admin or user
accounts).
MAC address — Make a note of the touchpanel MAC address.
SSL security certificates and IEEE 802.1X authentication — Extron touchpanels
come with a factory-installed Secure Sockets Layer (SSL) security certificate. IEEE
802.1X authentication is also supported once enabled (see Secure Sockets Layer
(SSL) Certificates on page 37 or IEEE 802.1X Certificates on page 37).
3. Prepare to mount the Cable Cubby:
Make sure you are familiar with all the Included Parts (see page 8) and have all
the Tools Required for Installation (see page 8) for installing the Cable Cubby.
Plan where you are going to install the Cable Cubby and how you are going to cut the
hole.
Ensure the TLP Pro 720C is oriented correctly and that there is adequate room for
cables and cable retractors (optional).
Ensure you are using the correct cut-out template or dimensions (see Cut-out
Dimensions on page 9).
Ensure the installation complies with all applicable regulations.
TLP Pro 720C • Installation Overview 4
4. Set up the touchpanel for network communication. Connect power to the touchpanel
If required, connect a 12 VDC power supply (see Power Connector on page 18).
Alternatively, connect the LAN port to a Power over Ethernet power injector (see
Network and Power over Ethernet Connector on page 20).
ATTENTION:
Do not power on the touchpanels or control processors until you have read
the Attention notice on page 18 (12 VDC power supply) or on page 20 (PoE
injector).
Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu
les mises en garde page 18 (source d’alimentation 12VCC) ou page 20
(injecteur PoE).
Use the Setup Menu (see page 22) or Toolbelt to set the DHCP status and,
if necessary, the IP address, subnet mask, gateway, and related settings for the
touchpanel.
5. Mount the Cable Cubby:
Disconnect the power supply and the network cable.
Cut the table surface (see Cutting the Table on page 9).
ATTENTION:
The opening in the table for the Cable Cubby should be cut only by licensed
and bonded craftspeople. Exercise care to prevent scarring or damaging the
furniture.
L’ouverture dans la table pour le Cable Cubby doit être coupée uniquement
par un ouvrier détenteur d’une licence. Veillez à ne pas laisser de marques
ni à détériorer le mobilier.
Run cables to the unit. These include Ethernet cable and cables for Retractors, power
modules, AAPs, and MAAPs (see Running Cables on page 11).
Leave enough slack to connect the cables before the enclosure is installed in the
table.
(Optional) Install cable retractors) (see Installing Cable Retractors (Optional) on
page 11).
(Optional) Install the power module (see Installing Power Modules (Optional) on
page 12).
Put together and install the AAP assembly (see Preparing and Installing the AAP
Assemblies on page 13).
Mount the Cable Cubby (see Mounting the TLP Pro 720C Enclosure on
page 15.
Connect the power supply or Power over Ethernet power injector.
TLP Pro 720C • Installation Overview 5
6. Configure the Touchpanels (see Using the Software on page 30).
Connect the PC that you will use for setup to the same Ethernet subnetwork as the
touchpanel.
Connect a control processor to the same Ethernet subnetwork.
Use GUI Designer to configure the touchpanel interface.
Use Global Configurator Plus and Professional or Global scripter to assign functions
to the screen elements.
The GUI Designer Help File, the Global Configurator Help File, and the Toolbelt Help File
provide step-by-step instructions and detailed information.
The Global Configurator Help File also includes an introduction to that software and sections
on how to start a project and configuration.
Global Scripter provides an Extron-exclusive Python library (ControlScript) and Global Scripter
modules to get you started. See the GlobalScripter Help File for more information.
NOTE: Frequently touched devices, such as touchscreens, require regular cleaning to
ensure their surfaces remain sanitary. Plastic surfaces and cosmetic finishes can be
damaged by long term exposure to chemicals. For Best Practices for Cleaning Your
Extron Products, see page 34.
TLP Pro 720C • Installation Overview 6
Mounting the
TLPPro720C
This section describes how to mount the TLP Pro 720C Cable Cubby. It covers:
Planning
Tools Required for Installation
Included Parts
Ensure Adequate Under-table Clearance for Retractors
Cutting the Table
Running Cables
Installing Cable Retractors (Optional)
Installing Power Modules (Optional)
Preparing and Installing the AAP Assemblies
Mounting the TLP Pro 720C Enclosure
Planning
1. Before making any cuts, select the best location for the TLPPro 720C.
Ensure that the edge that opens on the lid is oriented correctly.
Ensure there is enough space for all the system cables and components, above and
below the table. Take account of:
Clearances for under-table cabling, especially if the cable has a large bend radius.
Ensure Adequate Under-table Clearance for Retractors if they are to be
installed (see page 9).
The number and type of AAPs required for the installation.
The location of devices that connect to the AAPs either above or below the table.
2. Verify that you have the correct template or dimensions (see Cutting the Surface on
page 10).
3. Decide on the method for cutting a hole in the table (see Cutting the Table on
page 9)
. There are three methods available:
Hand router with routing template (see page 10) — requires a router template,
which must be purchased separately.
CNC router (see page 10) — must be programmed with the correct dimensions.
Reciprocating saw or jigsaw (see page 11) — requires a paper template
(available at www.extron.com).
The hand router used with the routing template or the CNC wood router are the most
accurate methods for cutting the hole. Either one of these methods is recommended by
Extron. The jigsaw is less accurate, but is also acceptable.
4. Check all relevant regulations.
Ensure that the installation complies with local, state, and national building and
electrical codes.
Ensure that the installation complies with the Americans with Disabilities Act or other
accessibility requirements.
TLP Pro 720C • Mounting the TLP Pro 720C 7
Tools Required for Installation
Safety Glasses
Phillips Screw Driver
Tape Measure
1/4" Hex Nut Driver
Marking Pen
Square
Vacuum Cleaner
Figure 2. Tools Required to Install the TLP Pro 720C
Included Parts
Open the shipping container and verify that all the following components are present:
TLP Pro 720C
Table Clamps
AC Power Module*
Blank AAPs
Pass-thru AAPs
Extron
Extron
Extron
Extr
on
Extron
Removal Tool
Zip Ties
#4−40 Screws
and Nuts
2 Pos
AAP Shelf Bracket Kits
(2 brackets/kit)
3 Pos1 Pos
With Power Module Without Power Module
AC Power Module
1
1 0
Pass-through AAPs
2, 3
3 3
Blank AAPs 6 6
1-position Bracket Kit 0 1
4
2-position Bracket Kit 3 4
3-position Bracket Kit 1 1
NOTES:
1
Inside the US, the TLP Pro 720C can be purchased with or without an
ACpower module. Outside the US, see www.extron.com to find a power
module that is suitable for your location.
2
Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than
the front bracket and has two holes for screws.
3
Active or Passive AAPs are not provided and must be purchased separately
(see www.extron.com).
4
Single-space brackets can only be installed in one location (see the Note and
figure
on page 13).
Figure 3. Parts Included with the TLP Pro 720C
TLP Pro 720C • Mounting the TLP Pro 720C 8
Ensure Adequate Under-table Clearance for Retractors
Retractors are optional accessories for handling cables with the TLP Pro 720C. If you are
using retractors, ensure that there is sufficient room beneath the table to accommodate them.
Horizontal mounting provides maximum legroom and protects the retractors from accidental
damage. Vertical mounting is used if space or access makes horizontal mounting difficult. To
satisfy ADA compliance requirements, there is also an option to mount the retractors at a 30°
angle (see the Retractors User Guide, which is available at www.extron.com).
Horizontal Mounting Clearance
XL Models
Vertical Mounting Clearance
XL Models
3.0"
(7.6 cm)
2.7" (6.9 cm)
17.0"
(43.3 cm)
23.0" (58.5 cm)
24.1"
(61.2 cm)
30.1"
(76.5 cm)
2.7" (6.9 cm)
9.8"
(24.9 cm)
3.0"
(7.6 cm)
9.8"
(24.9 cm)
Figure 4. Under-table Clearance Requirements for Retractors
Cutting the Table
Cut-out Dimensions
There are three alternative methods of making the hole for the TLP Pro 720C (see Cutting the
Surface on page 10):
If using a Hand router with routing template (see page 10), you should purchase the
TLP Pro 720C routing template (part number 70-980-01).
If using a CNC router (see page 10), use the exact cut-out dimensions.
If using a Reciprocating saw or jigsaw (see page 11) use the paper cut-out template.
TLP Pro 720C • Mounting the TLP Pro 720C 9
Cutting the Surface
WARNING: Wear safety glasses when operating power equipment. Failure to comply
can result in eye injury.
AVERTISSEMENT : Portez des lunettes de sécurité lorsque vous utilisez l’équipement
électrique. Ne pas respecter cela peut conduire à une blessure à l’oeil.
ATTENTION:
The opening in the table for the Cable Cubby should be cut only by licensed and
bonded craftspeople. Exercise care to prevent scarring or damaging the furniture.
L’ouverture dans la table pour le CableCubby devrait être coupée seulement par
des artisans autorisés et qualifiés. Faites attention à ne pas faire de marques sur le
meuble et à ne pas l’endommager.
Use the appropriate metal Extron routing template or refer to the surface cutout
dimensions before cutting a hole in the furniture or other surface. Pay special
attention to the direction the unit will face. The connector access side is underlined
(see CNC Router below). Extron is not responsible for miscut mounting holes.
Utilisez le gabarit de détourage métallique approprié ou reportez-vous aux
dimensions de découpe de la surface indiquées ci-après avant de découper
le meuble ou la surface. Faites particulièrement attention à la directions dans
laquelle l’unité sera dirigée. Le côté pour accéder au connecteurs est souligné (voir
CNCRouter ci-dessous). Extron ne sera pas responsable des erreurs de coupe.
The surfaces of the Cable Cubby enclosure have screws and other protrusions that
could damage fine furniture. Do not rest the enclosure on unprotected furniture.
La surface du boîtier Cable Cubby a des vis et d’autres éléments en saillie qui
pourrait endommager des meubles fins. N’appuyez pas le boîtier sur du moblier non
protégé.
Ensure the table surface is at least 0.375 inches (0.95 cm) thick.
Assurez vous que la surface de la table est au moins 0,95 cm (0,375”) d’épaisseur.
Be certain the cut is laid out in exactly the desired location and the edge that opens on the lid
is correctly oriented. After verifying and checking dimensions, cut a hole in the surface of the
furniture where the enclosure will be installed.
Hand router with routing template
If using a routing template, make sure it is the correct template for the TLPPro 720C (part
number 70-980-01). For complete instructions, see the RoutingTemplateUserGuide, available
at www.extron.com.
NOTE: The metal router guide must
be purchased separately. It is reusable
and should not be discarded when the
installation is complete.
CNC router
If using a CNC router, enter the correct
dimensions for the TLPPro 720C:
8.90 +0.00/-0.02 inches W x 7.1 +0.00/-0.02 inches D
226.11 +0.0/-0.5 mm W x 180.3 +0.0/-0.5 mm D
NOTE: The width dimension (underlined) refers to the side with AAP access.
HSA 200
USER ACCESS
HSA 200
CABLE CUBBY 300
CABLE CUBBY 300
USER ACCESS
TLP Pro 720C • Mounting the TLP Pro 720C 10
Reciprocating saw or jigsaw
If using a reciprocating saw or jigsaw, make
sure to use the paper cutout template for the
TLPPro720C. The template is available at
www.extron.com.
Running Cables
Run all cables necessary to support the AC connector, the cables stored in the cubby, and
all planned AAP connectors. Run the cables below the table and through the hole that was
cut in the previous step (see Cutting the Surface on page 10). Leave enough slack in the
cables to connect or route them before the cubby is installed in the table. Leave enough slack
for the external power supply and to connect AV cables and the cable for PoE and LAN to the
TLPPro 720C.
Installing Cable Retractors (Optional)
Extron cable retractors retract and store extended cables in Cable Cubby systems, preventing
them from tangling underneath the table. Retractor kits are available for several cable types.
Up to six retractors can be installed in the TLPPro 720C enclosure (three on either end). They
are not provided with the TLPPro 720C and must be purchased separately.
The buttons on the retractors must be placed at one end of the unit and must, therefore, be
the first or the last items added.
Secur
e the bolt
with the nut.
Secure the locking screw
on each retractor.
Do not overtighten.
Insert the bolt thr
ough the
r
etractor mounting hole on
the side of the Cable Cubby
and r
etractor assembly.
2
3
4
Insert retractors into the
touchpanel enclosure
from underneath.
1
Figure 5. Installing Cable Retractors
To mount the retractors horizontally and for further information and installation instructions,
see the Retractors User Guide, which is available at www.extron.com. The guide also
provides information about mounting the retractors at a 30° angle to satisfy ADA compliance
requirements.
Cut-Out Template for the Extron
TLP Pro 720C
Outer Edge of Trim Ring
(Do not cut this line.)
1. Confirm the product to be installed.
2. Remove the surface cut-out area
(gray) from the template.
3. Mark the position on the wall or
furniture where the TLP 710MV
is being installed.
4. Cut the opening.
P/N 68-2046-01 Rev. B
Page size: 11" x 17"
Print scale 1:1
Do not shrink.
P/N
P/
TLP Pro 720C • Mounting the TLP Pro 720C 11
Installing Power Modules (Optional)
WARNING:
Switch off all electrical power before connecting the AC conduit to a junction box,
and keep power off until installation is complete.
Débranchez toutes les sources d’alimentation électrique avant de connecter le
conduit d’alimentation à un boîtier d’encastrement, et gardez l’alimentation éteinte
jusqu’à ce que l’installation soit complète.
AVERTISSEMENT :
If the power cable is installed next to the retractors, ensure the power cable cannot
get tangled in the cable retractor mechanism.
Si le câble d’alimentation est installé à côté des rétracteurs, assurez vous qu’il ne
puisse pas s’emmêler dans le mécanisme du rétracteur de câbles.
ATTENTION:
All electrical installation must be performed by qualified personnel in accordance with
local and national building codes and electrical codes.
Toute installation électrique, doit être effectuée par un personnel qualifié,
conformément aux codes du bâtiment, aux codes incendie et sécurité, et aux codes
électriques, locaux et nationaux.
NOTE: Different countries require different power adapters. For models that do not
include a power module, see www.extron.com to select a power module that is
suitable for your location.
The power module takes up two or three AAP spaces and may be installed before or after the
AAP assembly is installed or, if desired, with AAPs on either side.
1. Secure the power module into position with #4-40 Phillips head screws and star washers.
CAUTION: Risk of electric shock: To ensure proper electrical grounding, use the
provided grounding screws and star washers.
ATTENTION : Risque de choc électrique: Afin d’assurer une mise à la terre
correcte, utilisez les fixations de mise à la terre et les rondelles en étoile fournies.
Secur
e the power module
t
o the TLP Pro 720C frame
with #4-40 Phillips head
sc
rews and star washers.
Extron
Figure 6. Installing Power Modules in the TLP Pro 720C
2. Run the cable or conduit to a convenient junction box. Extron recommends the circuit be
attached to a junction box that is directly wired to the main circuit.
TLP Pro 720C • Mounting the TLP Pro 720C 12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

Extron TLP Pro 720C User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages