Extron TLP Pro 720C User manual

TLP Pro 720C

User Guide

TouchLink

TouchLink Pro Touchpanel Control Systems

68-2406-01 Rev. B

01 21

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within

the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron website,

www.extron.com.

Sicherheitsanweisungen • Deutsch

WARUNG: Dieses Symbol auf demProdukt soll den Benutzer darauf

aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes

gefährliche Spannungen herrschen, die nicht isoliert sind und die einen

elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den

Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de importantes instrucciones de

uso y mantenimiento estas estan incluidas en la documentación

proporcionada con el equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad de

Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec

l’équipement.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,

la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les

informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site

Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire

l’utente della presenza di tensione non isolata pericolosa all’interno

del contenitore del prodotto che può costituire un rischio di scosse

elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire

l’utente della presenza di importanti istruzioni di funzionamento e

manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida

alla conformità normativa e di sicurezza di Extron, cod. articolo 68-290-01, sul

sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej

zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron

bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01,

na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению

электрическим током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций по

эксплуатации и обслуживанию в руководстве, прилагаемом к

данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других вопросах

см. руководство по безопасности и соблюдению нормативных

требований Extron на сайте Extron: , www.extron.com,

номер по каталогу - 68-290-01.

All trademarks mentioned are the property of their respective owners..

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

), registered service marks (

), and trademarks (

) are the property of RGBSystems, Inc. or Extron

(see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, Global

Configurator, Global Scripter, GlobalViewer, Hideaway, HyperLane, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort,

NAV, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch,

StudioStation, System I

NTEGRATOR, TeamWork, TouchLink, VideoLounge, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP

Systems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-RATE Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D Ripple

Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP

Configurator, DSVP (Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP,

MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC - QuickSwitch Front Panel Controller, Room Agent, Scope-Trigger, SIS - Simple

Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한

자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수

안내서, 68-290-01 조항을 참조하십시오.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户, 该产品机壳内有暴露的危险

电压，有触电危险。

注意：产品上的这个标志意在提示用户, 设备随附的用户手册中有重

要的操作和维护(维修)说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使

用的特性等相关内容，

敬请访问 Extron 网站 , www.extron.com，参见 Extron 安全规范指南，产品编号

68-290-01

。

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在未隔離的危

險電壓，可能會導致觸電之風險。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有重

要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，

請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手

冊》，準則編號 68-290-01。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

interference. This interference must be corrected at the expense of the user.

NOTE:

• This unit was tested with shielded I/O cables on the peripheral devices. Shielded

cables must be used to ensure compliance with FCC emissions limits.

• For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron website.

Conventions Used in this Guide

Notiﬁcations

In this user guide, the following are used:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Directory paths that do not have variables are written in the font shown here:

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the

File menu, select New.

Click the

OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at www.extron.com/technology/glossary.aspx.

Contents

Introduction............................................................ 1

About the TLP Pro 720C .................................... 1

Features ............................................................. 1

Application Diagram ........................................... 2

Requirements ..................................................... 3

Software ......................................................... 3

Hardware ........................................................ 3

Installation Overview ........................................... 4

Mounting the TLPPro720C ............................... 7

Planning ............................................................. 7

Tools Required for Installation ............................. 8

Included Parts .................................................... 8

Ensure Adequate Under-table Clearance for

Retractors ......................................................... 9

Cutting the Table ................................................ 9

Cut-out Dimensions ........................................ 9

Cutting the Surface ....................................... 10

Running Cables ............................................... 11

Installing Cable Retractors (Optional) ................ 11

Installing Power Modules (Optional) .................. 12

Preparing and Installing the AAP Assemblies .... 13

Installing AAPs .............................................. 13

Inserting the AAP Assemblies ....................... 14

Mounting the TLP Pro 720C Enclosure ............. 15

Panel Features .................................................... 16

Front Panel Features ......................................... 16

Connectors ...................................................... 18

Power Connector ......................................... 18

Network and Power over Ethernet

Connector ................................................... 20

On-screen Menus ............................................... 22

Setup Menu ...................................................... 22

Status Screen ............................................... 22

Network Screen ............................................ 23

Display Screen .............................................. 25

Audio Screen ................................................ 26

Advanced Screen ......................................... 27

Calibration Screen ............................................ 28

Conﬁguration Software ..................................... 29

Installing Software ............................................ 29

Using the Software ........................................... 30

TLP Pro 720C Web Page ................................. 31

Updating the Firmware ..................................... 33

Downloading Firmware ................................. 33

Reference Material ............................................. 34

Best Practices for Cleaning Your

Extron Products ............................................... 34

Network Port Requirements and Licensed

Third-Party Software Used in

the Touchpanels .............................................. 34

Reset Modes .................................................... 35

Use Factory Firmware ................................... 35

Reset All IP Settings ..................................... 35

Reset to Factory Defaults .............................. 36

Enable or Disable the DHCP Client ............... 36

Secure Sockets Layer (SSL) Certiﬁcates ........... 37

IEEE 802.1X Certiﬁcates ................................... 37

Certiﬁcate File Requirements......................... 38

Private Key File Requirements ....................... 38

TLP Pro 720C • Contents vii

TLP Pro 720C • Contents viii

Introduction

This guide describes the function, installation, and operation of the Extron TLPPro720C

TouchLink Pro Touchpanel. Unless otherwise stated, the terms TLP Pro and touchpanel refer

to the TLP Pro 720C.

The TLP Pro 720C is ideal for any AV application requiring a full-size, Cable Cubby touchpanel

with a customizable interface.

This section provides an overview of these products:

• About the TLP Pro 720C

• Features

• Application Diagram

• Requirements

About the TLP Pro 720C

The Extron TLP Pro 720C is a Cable Cubby touchpanel with a flip-up, 7-inch 800x480

(WVGA), LCD touchscreen with 18-bit color depth. It

combines the AV system control

of TLPPro720Series touchpanels with the cable management convenience of the

CableCubby. It features a tilt-up, full-color touchscreen in an elegant, metal enclosure that

can be mounted securely into a tabletop, lectern, or other ﬂat surface.

The user can define the graphics and the functions associated with those graphics, providing

versatility and adaptability to the configuration and control of an AV system. The screen layout

is designed with the Extron GUI Designer software. The functions can be assigned to the

screen objects with the Extron Global Configurator Plus and Global Configurator Professional

configuration software or with Global Scripter programming software.

A motion sensor, light sensor, and a speaker provide sleep mode, auto dimming, and audible

feedback respectively.

Features

7-inch flip-up LCD touchscreen — With 800x480 resolution and 18-bit color depth.

Faster processing and more memory — Allows for quicker configuration uploads and more

storage for GUI pages.

Compatible with the full range of Extron IPL Pro and IPCP Pro control processors —

Allows easy integration into existing systems.

Power over Ethernet (PoE 802.3af, Class3) compliance —

Allows the touchpanel to

receive power and control over a single Ethernet cable, eliminating the need for a local

power supply. The PoE injector is sold separately.

Built-in speaker — Mounted in the Cable Cubby compartment, with improved audio

performance provide audible feedback from button presses.

Light sensor — Adjusts screen brightness as the ambient room lighting changes.

Cable Cubby design — Offers easy access to AV, data, and power connections. AC power

modules are available for US, Europe, and other major world markets. AV connectivity options

include:

• Up to 11 single-space AAP-Architectural Adapter Plates.

• Up to 6 Retractor Cable Retraction Systems.

TLP Pro 720C • Introduction 1

Convenient LED lighting — Illuminates power and AV Cable Cubby area.

Integrated lid switch — Automatically wakes the touchpanel when opened and can trigger

any other system function.

System connection status indicator — Provides visual feedback if the touchpanel is not

communicating with a control processor.

Automatic clock synchronization — Allows touchpanel to display the accurate time and

date.

Adjustable sleep timer — Puts touchpanel into sleep mode.

Fully customizable using Extron control system software — GUI Designer combined

with Global Configurator Plus, Global Configurator Professional, or Global Scripter.

Supports Extron Control App and Extron Control for Web.

JITC Certified — Successfully completed interoperability and information assurance testing

for use in government applications and other mission-critical environments.

Installation routing template is available.

Highly reliable, energy-efficient external universal power supply optional — Provides

worldwide power compatibility, with high demonstrated reliability and low power consumption

for reduced operating costs.

Application Diagram

This diagram shows a typical application for the TLP Pro 720C touchpanel.

POWER

12V

--A MAX

Tx Rx RTSCTS

COM 1

Tx Rx

COM 2

VCG

VOL

RELAYS

1 2 C

1 2 3 4 G

DIGITAL I/O

PWR OUT= 6W

eBUS

+V +S

-S

LAN

IPCP PRO 250

IR/S

S G

SIGNAL

INPUT

CONFIG

HDCP

2-CH PCM

BITSTREAM

SIGNAL

OUTPUT

HDCP

ANALOG

S/PDIF

HAE 100

HDMI AUDIO EXTRACTOR

RGB - HDMI 300 A

MENU ENTER

ADJUST

CONFIG

RGB - HDMI 300 A

MENU ENTER

ADJUST

CONFIG

RGB - HDMI 300 A

MENU ENTER

ADJUST

CONFIG

DXP SERIES

DIGITAL CROSSPOINT MATRIX SWITCHER

C O N T R O L I/O

CONFIG

7 8

OUTPUTS

6 7

INPUTS

ENTERPRESET

VIEW ESC

VIDEOAUDIO

PUSH PUSH

POWERGUIDE MENU RES480 480p 720p 1080i 1080p

DIRECTV HD

SELECT

DIRECTV

BASSLEVELTREBLE

MINI POWER AMPLIFIER

MPA 152 Plus

STEREO

DUAL

MONO

Extron

Help

System

Off

Display

Room

Control

Off

Mute

Screen

Lighting

December 15, 2013 - 7:58 AM

Audio

Control

Volume

Mute

Tuner

1 2 3

VCRLaptop PC DVD

Doc

Cam

Tuner

Channel

Last

Presets

321

654

987

Enter

Ethernet

Satellite Receiver

TCP/IP

Network

Extron

TLP Pro 720C

7" Cable Cubby

TouchLink Pro Touchpanel

Extron

IPCP Pro 250

IP Link Pro

Control

Processor

Ethernet

Ethernet/PoE

RS-232

Extron DXP 84 HDMI

HDMI Matrix

Switcher

Volume Control

Extron MPA 152 Plus

Power Amplier

Video

Blu-ray Player

Laptop

Flat Panel Displays

Audio/VideoAudio/Video

Audio

Extron

RGB-HDMI 300 A

RGB to HDMI Scaler

Video

Laptop

Audio/Video

Audio

Audio/VideoAudio/Video

Video

Audio/Video

Audio

Video

Extron SI 26CT

Two-Way Ceiling Speakers

Extron HAE 100

HDMI Audio

Extractor

Extron

RGB-HDMI 300 A

RGB to HDMI Scaler

Extron

RGB-HDMI 300 A

RGB to HDMI Scaler

Figure 1. Application Diagram

TLP Pro 720C • Introduction 2

Requirements

Software

For a complete list of the requirements for running GUI Designer, Global Configurator Plus and

Professional, Global Scripter, and Toolbelt see the Extron web page (www.extron.com) for that

software.

NOTE: These touchpanels are not compatible with GlobalConfigurator 3 or

GUIConfigurator.

Hardware

An Extron IP Link Pro control interface must also be connected to the same network domain

as the TLP Pro TouchLink panel. See www.extron.com for a list of suitable controller processor.

NOTE: These touchpanels are not compatible with Extron IP Link (non-Pro) control

processors.

TLP Pro 720C • Introduction 3

Installation

Overview

This section provides an overview of the installation process. Follow the links for a more

detailed explanation of each step.

1. Before starting, download and install the latest versions of the following software:

 Global Configurator Professional or Global Configurator Plus — For setting up

and conﬁguring the control processor and touchpanel.

 GUI Designer — For designing layouts for Extron TouchLink Pro touchpanels and

third party touch interfaces.

 Global Scripter — Provides an integrated development environment for Extron

control systems programming.

 Toolbelt — Provides device discovery, device information, firmware updates,

and configuration of network settings, system utilities, and user management for

TouchLinkPro devices.

All four programs can be downloaded from www.extron.com (for information about using

the software, see Configuration Software (see page 29).

2. Obtain the following network information from your network administrator:

 DHCP status (on or off). If DHCP is off, you will also require

 IP address

 Subnet mask

 Gateway

 Username — by default these are either admin or user.

 Passwords — The factory configured passwords for all accounts on this device

have been set to the device serial number. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the password changes to the

default password. The default password is extron (for either admin or user

accounts).

 MAC address — Make a note of the touchpanel MAC address.

 SSL security certificates and IEEE 802.1X authentication — Extron touchpanels

come with a factory-installed Secure Sockets Layer (SSL) security certiﬁcate. IEEE

802.1X authentication is also supported once enabled (see Secure Sockets Layer

(SSL) Certiﬁcates on page 37 or IEEE 802.1X Certiﬁcates on page 37).

3. Prepare to mount the Cable Cubby:

 Make sure you are familiar with all the Included Parts (see page 8) and have all

the Tools Required for Installation (see page 8) for installing the Cable Cubby.

 Plan where you are going to install the Cable Cubby and how you are going to cut the

hole.

 Ensure the TLP Pro 720C is oriented correctly and that there is adequate room for

cables and cable retractors (optional).

 Ensure you are using the correct cut-out template or dimensions (see Cut-out

Dimensions on page 9).

 Ensure the installation complies with all applicable regulations.

TLP Pro 720C • Installation Overview 4

4. Set up the touchpanel for network communication. Connect power to the touchpanel

 If required, connect a 12 VDC power supply (see Power Connector on page 18).

 Alternatively, connect the LAN port to a Power over Ethernet power injector (see

Network and Power over Ethernet Connector on page 20).

ATTENTION:

• Do not power on the touchpanels or control processors until you have read

the Attention notice on page 18 (12 VDC power supply) or on page 20 (PoE

injector).

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu

les mises en garde page 18 (source d’alimentation 12VCC) ou page 20

(injecteur PoE).

 Use the Setup Menu (see page 22) or Toolbelt to set the DHCP status and,

if necessary, the IP address, subnet mask, gateway, and related settings for the

touchpanel.

5. Mount the Cable Cubby:

 Disconnect the power supply and the network cable.

 Cut the table surface (see Cutting the Table on page 9).

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed

and bonded craftspeople. Exercise care to prevent scarring or damaging the

furniture.

• L’ouverture dans la table pour le Cable Cubby doit être coupée uniquement

par un ouvrier détenteur d’une licence. Veillez à ne pas laisser de marques

ni à détériorer le mobilier.

 Run cables to the unit. These include Ethernet cable and cables for Retractors, power

modules, AAPs, and MAAPs (see Running Cables on page 11).

Leave enough slack to connect the cables before the enclosure is installed in the

table.

 (Optional) Install cable retractors) (see Installing Cable Retractors (Optional) on

page 11).

 (Optional) Install the power module (see Installing Power Modules (Optional) on

page 12).

 Put together and install the AAP assembly (see Preparing and Installing the AAP

Assemblies on page 13).

 Mount the Cable Cubby (see Mounting the TLP Pro 720C Enclosure on

page 15.

 Connect the power supply or Power over Ethernet power injector.

TLP Pro 720C • Installation Overview 5

6. Conﬁgure the Touchpanels (see Using the Software on page 30).

 Connect the PC that you will use for setup to the same Ethernet subnetwork as the

touchpanel.

 Connect a control processor to the same Ethernet subnetwork.

 Use GUI Designer to conﬁgure the touchpanel interface.

 Use Global Conﬁgurator Plus and Professional or Global scripter to assign functions

to the screen elements.

The GUI Designer Help File, the Global Configurator Help File, and the Toolbelt Help File

provide step-by-step instructions and detailed information.

The Global Configurator Help File also includes an introduction to that software and sections

on how to start a project and configuration.

Global Scripter provides an Extron-exclusive Python library (ControlScript) and Global Scripter

modules to get you started. See the GlobalScripter Help File for more information.

NOTE: Frequently touched devices, such as touchscreens, require regular cleaning to

ensure their surfaces remain sanitary. Plastic surfaces and cosmetic finishes can be

damaged by long term exposure to chemicals. For Best Practices for Cleaning Your

Extron Products, see page 34.

TLP Pro 720C • Installation Overview 6

Mounting the

TLPPro720C

This section describes how to mount the TLP Pro 720C Cable Cubby. It covers:

• Planning

• Tools Required for Installation

• Included Parts

• Ensure Adequate Under-table Clearance for Retractors

• Cutting the Table

• Running Cables

• Installing Cable Retractors (Optional)

• Installing Power Modules (Optional)

• Preparing and Installing the AAP Assemblies

• Mounting the TLP Pro 720C Enclosure

Planning

1. Before making any cuts, select the best location for the TLPPro 720C.

 Ensure that the edge that opens on the lid is oriented correctly.

 Ensure there is enough space for all the system cables and components, above and

below the table. Take account of:

• Clearances for under-table cabling, especially if the cable has a large bend radius.

• Ensure Adequate Under-table Clearance for Retractors if they are to be

installed (see page 9).

• The number and type of AAPs required for the installation.

• The location of devices that connect to the AAPs either above or below the table.

2. Verify that you have the correct template or dimensions (see Cutting the Surface on

page 10).

3. Decide on the method for cutting a hole in the table (see Cutting the Table on

page 9)

. There are three methods available:

• Hand router with routing template (see page 10) — requires a router template,

which must be purchased separately.

• CNC router (see page 10) — must be programmed with the correct dimensions.

• Reciprocating saw or jigsaw (see page 11) — requires a paper template

(available at www.extron.com).

The hand router used with the routing template or the CNC wood router are the most

accurate methods for cutting the hole. Either one of these methods is recommended by

Extron. The jigsaw is less accurate, but is also acceptable.

4. Check all relevant regulations.

 Ensure that the installation complies with local, state, and national building and

electrical codes.

 Ensure that the installation complies with the Americans with Disabilities Act or other

accessibility requirements.

TLP Pro 720C • Mounting the TLP Pro 720C 7

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

1/4" Hex Nut Driver

Marking Pen

Square

Vacuum Cleaner

Figure 2. Tools Required to Install the TLP Pro 720C

Included Parts

Open the shipping container and verify that all the following components are present:

TLP Pro 720C

Table Clamps

AC Power Module*

Blank AAPs

Pass-thru AAPs

Extron

Extr

Extron

Removal Tool

Zip Ties

#4−40 Screws

and Nuts

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

With Power Module Without Power Module

AC Power Module

1 0

Pass-through AAPs

2, 3

3 3

Blank AAPs 6 6

1-position Bracket Kit 0 1

2-position Bracket Kit 3 4

3-position Bracket Kit 1 1

NOTES:

Inside the US, the TLP Pro 720C can be purchased with or without an

ACpower module. Outside the US, see www.extron.com to ﬁnd a power

module that is suitable for your location.

Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than

the front bracket and has two holes for screws.

Active or Passive AAPs are not provided and must be purchased separately

(see www.extron.com).

Single-space brackets can only be installed in one location (see the Note and

ﬁgure

on page 13).

Figure 3. Parts Included with the TLP Pro 720C

TLP Pro 720C • Mounting the TLP Pro 720C 8

Ensure Adequate Under-table Clearance for Retractors

Retractors are optional accessories for handling cables with the TLP Pro 720C. If you are

using retractors, ensure that there is sufficient room beneath the table to accommodate them.

Horizontal mounting provides maximum legroom and protects the retractors from accidental

damage. Vertical mounting is used if space or access makes horizontal mounting difficult. To

satisfy ADA compliance requirements, there is also an option to mount the retractors at a 30°

angle (see the Retractors User Guide, which is available at www.extron.com).

Horizontal Mounting Clearance

XL Models

Vertical Mounting Clearance

XL Models

3.0"

(7.6 cm)

2.7" (6.9 cm)

17.0"

(43.3 cm)

23.0" (58.5 cm)

24.1"

(61.2 cm)

30.1"

(76.5 cm)

2.7" (6.9 cm)

9.8"

(24.9 cm)

3.0"

(7.6 cm)

9.8"

(24.9 cm)

Figure 4. Under-table Clearance Requirements for Retractors

Cutting the Table

Cut-out Dimensions

There are three alternative methods of making the hole for the TLP Pro 720C (see Cutting the

Surface on page 10):

• If using a Hand router with routing template (see page 10), you should purchase the

TLP Pro 720C routing template (part number 70-980-01).

• If using a CNC router (see page 10), use the exact cut-out dimensions.

• If using a Reciprocating saw or jigsaw (see page 11) use the paper cut-out template.

TLP Pro 720C • Mounting the TLP Pro 720C 9

Cutting the Surface

WARNING: Wear safety glasses when operating power equipment. Failure to comply

can result in eye injury.

AVERTISSEMENT : Portez des lunettes de sécurité lorsque vous utilisez l’équipement

électrique. Ne pas respecter cela peut conduire à une blessure à l’oeil.

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and

bonded craftspeople. Exercise care to prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le CableCubby devrait être coupée seulement par

des artisans autorisés et qualiﬁés. Faites attention à ne pas faire de marques sur le

meuble et à ne pas l’endommager.

• Use the appropriate metal Extron routing template or refer to the surface cutout

dimensions before cutting a hole in the furniture or other surface. Pay special

attention to the direction the unit will face. The connector access side is underlined

(see CNC Router below). Extron is not responsible for miscut mounting holes.

• Utilisez le gabarit de détourage métallique approprié ou reportez-vous aux

dimensions de découpe de la surface indiquées ci-après avant de découper

le meuble ou la surface. Faites particulièrement attention à la directions dans

laquelle l’unité sera dirigée. Le côté pour accéder au connecteurs est souligné (voir

CNCRouter ci-dessous). Extron ne sera pas responsable des erreurs de coupe.

• The surfaces of the Cable Cubby enclosure have screws and other protrusions that

could damage ﬁne furniture. Do not rest the enclosure on unprotected furniture.

• La surface du boîtier Cable Cubby a des vis et d’autres éléments en saillie qui

pourrait endommager des meubles ﬁns. N’appuyez pas le boîtier sur du moblier non

protégé.

• Ensure the table surface is at least 0.375 inches (0.95 cm) thick.

• Assurez vous que la surface de la table est au moins 0,95 cm (0,375”) d’épaisseur.

Be certain the cut is laid out in exactly the desired location and the edge that opens on the lid

is correctly oriented. After verifying and checking dimensions, cut a hole in the surface of the

furniture where the enclosure will be installed.

Hand router with routing template

If using a routing template, make sure it is the correct template for the TLPPro 720C (part

number 70-980-01). For complete instructions, see the RoutingTemplateUserGuide, available

at www.extron.com.

NOTE: The metal router guide must

be purchased separately. It is reusable

and should not be discarded when the

installation is complete.

CNC router

If using a CNC router, enter the correct

dimensions for the TLPPro 720C:

8.90 +0.00/-0.02 inches W x 7.1 +0.00/-0.02 inches D

226.11 +0.0/-0.5 mm W x 180.3 +0.0/-0.5 mm D

NOTE: The width dimension (underlined) refers to the side with AAP access.

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

USER ACCESS

TLP Pro 720C • Mounting the TLP Pro 720C 10

Reciprocating saw or jigsaw

If using a reciprocating saw or jigsaw, make

sure to use the paper cutout template for the

TLPPro720C. The template is available at

www.extron.com.

Running Cables

Run all cables necessary to support the AC connector, the cables stored in the cubby, and

all planned AAP connectors. Run the cables below the table and through the hole that was

cut in the previous step (see Cutting the Surface on page 10). Leave enough slack in the

cables to connect or route them before the cubby is installed in the table. Leave enough slack

for the external power supply and to connect AV cables and the cable for PoE and LAN to the

TLPPro 720C.

Installing Cable Retractors (Optional)

Extron cable retractors retract and store extended cables in Cable Cubby systems, preventing

them from tangling underneath the table. Retractor kits are available for several cable types.

Up to six retractors can be installed in the TLPPro 720C enclosure (three on either end). They

are not provided with the TLPPro 720C and must be purchased separately.

The buttons on the retractors must be placed at one end of the unit and must, therefore, be

the first or the last items added.

Secur

e the bolt

with the nut.

Secure the locking screw

on each retractor.

Do not overtighten.

Insert the bolt thr

ough the

etractor mounting hole on

the side of the Cable Cubby

and r

etractor assembly.

Insert retractors into the

touchpanel enclosure

from underneath.

Figure 5. Installing Cable Retractors

To mount the retractors horizontally and for further information and installation instructions,

see the Retractors User Guide, which is available at www.extron.com. The guide also

provides information about mounting the retractors at a 30° angle to satisfy ADA compliance

requirements.

Cut-Out Template for the Extron

TLP Pro 720C

Outer Edge of Trim Ring

(Do not cut this line.)

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Mark the position on the wall or

furniture where the TLP 710MV

is being installed.

4. Cut the opening.

P/N 68-2046-01 Rev. B

Page size: 11" x 17"

Print scale 1:1

Do not shrink.

P/N

TLP Pro 720C • Mounting the TLP Pro 720C 11

Installing Power Modules (Optional)

WARNING:

• Switch off all electrical power before connecting the AC conduit to a junction box,

and keep power off until installation is complete.

• Débranchez toutes les sources d’alimentation électrique avant de connecter le

conduit d’alimentation à un boîtier d’encastrement, et gardez l’alimentation éteinte

jusqu’à ce que l’installation soit complète.

AVERTISSEMENT :

• If the power cable is installed next to the retractors, ensure the power cable cannot

get tangled in the cable retractor mechanism.

• Si le câble d’alimentation est installé à côté des rétracteurs, assurez vous qu’il ne

puisse pas s’emmêler dans le mécanisme du rétracteur de câbles.

ATTENTION:

• All electrical installation must be performed by qualiﬁed personnel in accordance with

local and national building codes and electrical codes.

• Toute installation électrique, doit être effectuée par un personnel qualiﬁé,

conformément aux codes du bâtiment, aux codes incendie et sécurité, et aux codes

électriques, locaux et nationaux.

NOTE: Different countries require different power adapters. For models that do not

include a power module, see www.extron.com to select a power module that is

suitable for your location.

The power module takes up two or three AAP spaces and may be installed before or after the

AAP assembly is installed or, if desired, with AAPs on either side.

1. Secure the power module into position with #4-40 Phillips head screws and star washers.

CAUTION: Risk of electric shock: To ensure proper electrical grounding, use the

provided grounding screws and star washers.

ATTENTION : Risque de choc électrique: Afin d’assurer une mise à la terre

correcte, utilisez les fixations de mise à la terre et les rondelles en étoile fournies.

Secur

e the power module

o the TLP Pro 720C frame

with #4-40 Phillips head

rews and star washers.

Extron

Figure 6. Installing Power Modules in the TLP Pro 720C

2. Run the cable or conduit to a convenient junction box. Extron recommends the circuit be

attached to a junction box that is directly wired to the main circuit.

TLP Pro 720C • Mounting the TLP Pro 720C 12

Page is loading ...

Extron TLP Pro 720C User manual

Related papers

Other documents