MOUNTUP MP0011 User manual

Brand: MOUNTUP

Model: MP0011

Type: User manual

MOUNTUP MP0011 is a versatile TV mount designed to provide secure and flexible TV mounting solutions for a wide range of TV sizes and wall types. Crafted from high-grade materials, it ensures stability and durability, supporting TVs up to 60 lbs. The mount boasts a sleek and low-profile design, allowing your TV to sit just 1.1 inches from the wall, creating a clean and modern look. With its adjustable tilt mechanism, you can effortlessly angle your TV up to -10° or +5° for optimal viewing angles, reducing neck strain and enhancing your TV-watching experience.

Step 2A Wall plate installation (wood stud)

2A-1

2A-2

Locate your studs. Verify and mark the center of the stud

by finding the stud edges using an awl, a thin nail, or an

edge-to-edge stud finder.

Position the wall plate at your desired height and

line up the holes with your stud center line. Level the

wall plate and mark the pilot hole locations.

2A-3

Drill pilot holes using a 7/32 in. (5.5mm) diameter drill bit.

IMPORTANT:

Pilot holes must be drilled to a depth

of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.

Hardware Included

Max:400x400mm/16x16"

Min:75x75mm /3x3"

26"~55"

()

If you have any questions, please contact us.

Max:

(27KG)

60LBS

Safety Caution

Must Check Before Getting Started

Installation Tools (Not Included)

Band

Tape

Socket

Wrench

ScrewdriverPencil Electrodrill

Stud

Finder

HammerAwl Wood

Drill Bit

Masonry

Drill Bit

Wood Stud Installation Concrete Installation

1/2"

(13mm)

3/8"

(10mm)

7/32"

(5.5mm)

MAX:400mm/16"

MAX:

400mm/16" Max:

(27KG)

60LBS

Arm and Wall Plate

01 x1

Brackets

02 x2

Safety Locks

03 x2

Philips Screws

M6 x 15mm

M6 x 30mm

Philips Screws

M4 x 12mm

M4 x 30mm

Washers

Ø6mm

M4-5-6

Spacers

L10mm

x4 x4x4

Philips Screws

M8 x 25mm

M8 x 45mm

x4 x8 x4

Spacers

L5mm

TV Screws / Washers

M-A M-B M-C M-D M-E M-F

Step 1-1

Select TV screw diameter

Thread screws by hand into the threaded holes on the back of your TV to select which screw

diameter fits your TV.

M6M4 M8

Step 1-2 Select TV screw length

Correct Correct

Too Long

Too Short

Step 1-3

Attach the bracket

CAUTION: Ensure bracket is securely fastened before moving on to the next step.

Top of TV

(a) For Flat Back

(b) For Round Back / Extra Space

No!

7/32 in

Ø5.5 mm

When attaching brackets to the flat screen, be careful not to over tighten screws and

be sure that screws do not bottom out in the mounting holes.

2.75in (70 mm)

Bubble Level

Min. 8"

(203mm)

Solid concrete wall

CAUTION: DO NOT install into drywall alone.

Min. Wood Stud Size:

nominal 2”(51mm)

actual 1 1/2”(38mm)

Min. Wood Stud Size:

nominal 4”(102mm)

actual 3 1/2”(89mm)

<16mm(5/8")

Drywall with wood studs

MU0011 INSTALLATION INSTRUCTION

Please read this instruction carefully before installation.

If you do not understand these instructions or have doubts about the safety of the installation, assembly

or use of this product, please contact us.

● This product is designed for use in wood stud and solid concrete wall.

- DO NOT install into drywall alone.

● The wall must be capable of supporting five times the weight of the TV and mount combined.

● Do not apply this product to any purpose not indicated by MOUNTUP.

● Incorrect installation may result in product damage or body injury. MOUNTUP shall bear no responsibility

for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,

please contact us.

Velcro cable ties X5 Bubble level X1

Hardware (Wall /Product)

Lag Bolts 5/16 x 2½ in

x3 x1

Open-end wrench

M-A

Use the shorter screws

M-B

M-C

M-E

Not for M8 screws

M-FM-D

M-A

Use the longer screws

M-B

M-C

M-E

Not for M8 screws

Keep the

arrow up

1 2

43 5

2A-4

Position the wall plate at

your desired height, level the

wall plate and mark the pilot

hole locations x3.

2B-1

Step 2B Wall plate installation (concrete or brick)

Drill pilot holes

2B-2

Adjustments Adjustments

Product dimensions:

Bubble Level

No!

2.75in 70 mm

Ø 10 mm

3/8in

2B-3

No!

Step 3 Lift and hang TV with brackets onto wall bracket

-10°

+5°

Tool-free Tilting Adjustment

If necessary

Tighten

If TV keeps tilting down, Pull TV to desired

angle then fasten tilting nuts with the open-end

wrench.

If needed, TV can be leveled ±3 degrees via adjusting the 4 nuts with the

open-end wrench.

Leveling adjustment (-3°/+3°)

±3°

± 3°

Concrete Wall

directly to you.

Concrete wall anchor 3pcs (NOT INCLUDED)

Ø10*61mm

01 A

Install wall plate using lag bolts .

Tighten the lag bolts until they are

pulled firmly against the wall plate

01 A

Install wall plate using lag bolts

and anchors (not included).

Tighten the lag bolts until they are

pulled firmly against the wall plate

TV brackets have two-height -shifts.

You can choose your desired height.

Hang the TV with brackets to the bracket.

The second choice

The first choice

Attech the saftety locks

Secure

58mm/2.3"

100mm

/3.9"

100mm

/3.9"

224mm

/8.8"

8.7mm/0.3"

31mm/1.2"

150mm

/5.9"

MAX:400mm/16"

MIN:75mm/3"

28.6mm/1.1"

Φ8.9mm/0.4

MAX:400mm/16"

MIN:75mm/3"

435mm/17.1"

425mm

/16.7"

30mm/1.2"

40mm/1.6"

505mm/19.9"

20mm/0.8"

206mm/8.1" 206mm/8.1"

73mm

/2.9"

431mm/17"

+5°

-10°

89mm/3.5"

20mm/0.8"

10 11

76 8

109 11

MOUNTUP MP0011 User manual

MOUNTUP MP0011 User manual

MOUNTUP MP0011 User manual

Related papers

Other documents