MOUNTUP MU0015 Installation guide

Brand: MOUNTUP

Model: MU0015

Category: Wall & ceiling mounts accessories

Type: Installation guide

154LBS

70KG

Max:

Max:800x400mm/31.5x16"

Min:200x100mm /8x4"

47"~90"

(A0)

If you have any questions, please contact us via

help@jollyholding.com

MU0015 INSTALLATION INSTRUCTION

- 1 -

Velcro Cable Ties X5 Bubble Level X1 HDMI Cable X1

Hammer

3/8"(10mm)

Masonry Drill Bit

7/32"(5.5mm)

Wood Drill Bit

AwlStud Finder

Socket Wrench

1/2"(13mm)

ElectrodrillScrewdriverPencil

What is your wall

made of?

Solid concrete

wall?

● This product is designed for use in wood stud or solid concrete wall.

- DO NOT install into drywall alone.

● The wall must be capable of supporting five times the weight of the TV and mount

combined.

● Do not apply this product to any purpose not indicated by MOUNTUP.

● Incorrect installation may result in product damage or body injury. MOUNTUP shall

bear no responsibility for any damage or in

jury resulted from incorrect installation,

incorrect assembly or misuse.

Please read this instruction carefully before installation.

If you do not understand these instructions or have doubts about the safety of the

installation, assembly or use of this product, contact Customer Service via

help@jollyholding.com

Safety Caution

2M2M

Band Tape

Drywall with

wood studs?

CAUTION:

Yes --- Perfect!

No --- This mount is NOT compatible.

MAX:

400mm/16"

MAX:800mm/31.5"

Yes --- Perfect!

No --- This mount is NOT compatible.

Installation Tools

(Not Included)

2 Does your TV

(including accessories)

weigh less than

154 LBS (70KG)?

1 Is your TV VESA

equal to/greater than

200x100mm /8x4" and

equal to/less than

800x400mm/31.5x16"?

Before getting started, let’s make sure this mount is perfect for you!

154LBS

70KG

Max:

DO NOT install

into drywall alone

Perfect! Perfect!

Wood Stud Install

Concrete Install

- 2 -

Arm and Wall Plate

Vertical Brackets

End Cap

Hardware Included

Front Support

Hardware Wall /Product)

5/16 x 2½ in

Lag Bolts

Washers

Ø8mm

This product contains

small items that could be a choking hazard if

swallowed. Before starting assembly, verify

all parts are included and undamaged. If

any parts are missing or damaged, do not

return the damaged item to your dealer;

please contact our customer service team.

Never use damaged parts!

NOTE: Not all parts and hardware included

will be used.

WARNING:

Open End Wrench

- 3 -

Philips Screws

M6 x 15mm

M6 x 30mm

Philips Screws

M4 x 12mm

M4 x 30mm

Washers

Ø6mm

M4-5-6

Spacers

L10mm

x4x4

Philips Screws

M8 x 25mm

M8 x 45mm

x4 x8 x4

Spacers

L5mm

TV Screws / Washers

M-A M-B M-C M-D M-E M-F

16”

24”

18”

STEP 1-2

Attach the Brackets

Position your brackets over your TV hole pattern - making sure the brackets are centered

and level over the TV hole pattern.

Secure the brackets using your screw/washer/spacer selection:

(a) for Flat Back

(b) for Round Back / Extra space

CAUTION: Ensure bracket is securely fastened before moving on to the next step.

- 4 -

(a) Flat Back

M-E

Not for M8 screws

M-A

Use the shorter screws

M-B

M-C

(a) For Flat Back

1. Select TV screw diameter: Thread screws by hand into the threaded holes on the

back of your TV to select which screw diameter fits your TV.

2. Select TV screw length: When attaching brackets to the TV, be careful not to over

tighten screws and be sure that screws do not bottom out in the mounting holes.

M6M4

Correct

Too Long

Too Short

STEP 1-1 Select Proper TV Screw

STEP 1-2

Attach the Brackets

(b) Round Back /

Extra Space

M-E

M-D

M-F

Not for M8 screws

- 5 -

STEP 2A Wall Plate Installation (Wood Stud)

M-A

Use the longer screws

M-B

M-C

2A-1

Locate your studs. Verify and

mark the center of the studs by

finding the stud edges using an

awl, a thin nail, or an

edge-to-edge stud finder.

2A-2

Position the wall plate [01]

at your desired height and

line up the holes with your

stud center line. Level the

wall plate and make the

holes.

16 ~ 24 in

(b) For Round Back / Extra Space

Install wall plate [01] using lag

bolts [A] and washers [B].

Tighten the lag bolts [A] until

they are pulled firmly against

the wall plate [01]

STEP 2A Wall Plate Installation (Wood Stud)

- 6 -

2A-4

2A-3

16 ~ 24 in

2.75 in. (70 mm)

7/32 in.

(5.5 mm)

Drill pilot holes using a 7/32 in. (5.5 mm)

diameter drill bit.

IMPORTANT:

Pilot holes must be

in. (70 mm).

Be sure to drill into the center of the stud.

drilled to a depth of

STEP 2B Wall Plate Installation (Concrete or Brick)

- 7 -

2B-1

Position the wall plate

[01] at your desired

height , level the wall

plate and mark the pilot

hole locations.

Drill pilot holes

2B-2

2.75in 70 mm

Ø 10 mm

Concrete Wall

Install wall plate [01] using

lag bolts [A], washers [B]

and anchors (not included).

Tighten the lag bolts [A]

until they are pulled firmly

against the wall plate [01].

2B-3

these additional pieces shipped directly to you.

Concrete Wall Anchor

4pcs

Concrete wall anchor (NOT INCLUDED)

OPTIONAL Change the arm position on the wall plate

- 8 -

Install wall plate [01] using

lag bolts [A], washers [B]

and anchors (not included).

Tighten the lag bolts [A]

until they are pulled firmly

against the wall plate [01].

Install the End Caps [03] to Front Support [02] with the preassembled screws.

3-1

Pre-assembled scews

STEP 3 Install Front Support and End Cap Together

If necessary, you can move the Arm Assembly laterally to center your TV, Secure Arm

Assembly to Wall Plate using removed screws.

Remove 4 bolts and washers using a

M6 Allen key (not included).

Slide the arm assembly to

desired placement

Assemble the wall palte and the arm assembly using the 4 bolts and washers

removed from the previous step.

IMPORTANT!

Ensure that the top of the arm

assembly tucks INSIDE the

back of the top wall plate.

1 2

3-2

Hang 02 onto 01 and using a screwdriver to secure with preassembled screws [P1]

and washer [P2] .

Remove the

preassembled

screws [P3] and

save to use, then

raise the safety

locks.

Press the safety locks then fasten

the removed screws [P3].

Lift and hang the TV with the bracket onto the arm

and wall plate [02].

02 03

STEP 4 Hang TV with brackets onto the arm extensions

- 9 -

STEP 3 Install Front Support and End Cap Together

- 10 -

Adjustments

(Tilting)

(Leveling)

Tilting Angle Adjustment (+3° / -15°)

Loosen tilting nuts, pull TV to your

desired angle, then fasten tilting nuts

with open end wrench [C].

Loosen

Tighten

Loosen

Tighten

±3°

TV Leveling Adjustment (-3°/+3°)

Loosen 2 leveling bolts on the rear of TV

plate with the open end wrench [C],

adjust to level, and retighten to secure.

- 11 -

Product dimensions:

71mm (2.8”)

+3°/-15°

600mm (23.6”)

-3°/+3°

Max 800mm(31.5”)

Max 400mm(15.7”)

237mm(9.3”)

430mm(16.9”)

915mm(36”)

MOUNTUP MU0015 Installation guide

Brand: MOUNTUP

Model: MU0015

Category: Wall & ceiling mounts accessories

Type: Installation guide

Download PDF

report

MOUNTUP MU0015 Installation guide

MOUNTUP MU0015 Installation guide

Related papers

Other documents