MOUNTUP MU0058 Installation guide

Brand
MOUNTUP
Model
MU0058
Category
Wall & ceiling mounts accessories
Type
Installation guide
NOTE: Not all parts and hardware included will be used.
INSTALLATION INSTRUCTION
YZ2303_US1.0
Product Dimensions
Supplied Parts and Hardware
TV
Spacers
H10mm
×8
MD
Washers
Ф6mm
M4-5-6
×4
ME
Spacers
H5mm
×8
MF
Philips Screws
×4
MA
Philips Screws Philips Screws
×4 ×4
MB
×4 ×4
MC
×4
M4 x 12mm
M4 x 30mm
M6 x 15mm
M6 x 30mm
M8 x 25mm
M8 x 45mm
Extra Tools You Need (Not Supplied)
Band
Tape
2M
Socket
Wrench
ScrewdriverPencil Electrodrill
1/2"
(13mm)
HammerMasonry
Drill Bit
For
Concrete Wall
Ф3/8"
(Ф10mm)
Stud
Finder
Awl Wood
Drill Bit
For
Wood Studs
Ф7/32"
(Ф5.5mm)
Please read this instruction carefully before installation. If you do not understand these
instructions or have doubts about the safety of the installation, assembly or use of this
product, please contact us.
● This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
● The wall must be capable of supporting five times the weight of the TV and mount combined.
● Incorrect installation may result in product damage / property damage or body injury.
We shall bear no responsibility for any damage or injury resulted from incorrect installation,
incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are
missing or damaged, do not return the damaged item to your dealer; please contact our
customer service team. Never use damaged parts!
Safety Caution
If you have any questions, please feel free to contact Customer Service
via Amazon before returning.
Verify Your Wall Construction
MAX:
100 lbs (45 kg)
Load
Capacity
Must Check Before Getting Started
Minimum VESA Pattern (W × H):
150mm × 100mm / 6 in × 4 in
Maximum VESA Pattern (W × H):
600mm × 400mm / 24 in × 16 in
DO NOT install into drywall alone.
CAUTION:
CAUTION:
Avoid potential personal injuries and property damage!
Drywall covering the wall must not exceed 5/8 in. (16 mm).
Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm)
actual 1 ½ x 3 ½ in. (38 x 89 mm).
CAUTION:
Avoid potential personal injuries and property damage!
Mount the wall plate assembly directly onto the concrete
surface (no surface covering).
Min. 8"
(203mm)
Solid concrete wall
<5/8"(16mm)
Min.2"(51mm)
Min.4"(102mm)
Wall with wood studs
Max.16"(406mm)
Perfect!
Perfect!
cm
inches
W
H
Yes, choose the appropriate screws, washers,and spacers for your TV.
TV back
Bracket
Long Screw
Spacer
Washer
No, just choose the screws, washers.
Bracket Washer
TV back
Short Screw
01 040302
For more spacing
between bracket
and TV
For protruded
back TV
For counterbore
of TV
To avoid the
blocked input
1-2 Need Spacer?
1-1 Select TV Screws
1-3
Attach Brackets to TV
1
Do not tighten the screws excessively or tighten them by
using the Electrodrill, or your TV might be damaged.
M8
M6
M4
Correct Correct
Too LongToo Short Not Vertical
01
×1
Mount
Bubble Level
×1
T1
Velcro Cable Ties
×3
T2
Mounting Template
×1
T3
±3°
Level
MAX: 24"(600mm)
MIN: 6"(150mm)
MAX: 16.3"(413mm)
MIN: 2.4"(62mm)
11.8"
299mm
17"(430mm)
MAX:
16"(400mm)
MIN:
4"(100mm)
Swivel ±45°
+5°
-13°
Tilt
03
×4
Arm Extensions
04
×2
Side Cover
Assemble the Mount
2
1. Remove the
pre-assembled screws x8
2. Insert the
arm extensions
3. Fasten the all 8 screws.
2. Insert the
arm extensions
3. Secure the side covers with
the pre-assembled screws.
1. Remove the
pre-assembled
screws x4
2. Insert the
Side Cover x2
03
03
04
04
8"(203mm)
12"(305mm)
16"(203mm)
02
×2
Brackets
Not for M8 Screws
May be needed
TOP OF TV
Arrow Up
02
02
Wall / Product
Lag Bolt
ST8x65mm
Ax4
wrench
S10mm
x1
B
4-2
4-1
Hang and Secure TV to Wall Plate
4
Hang and secure TV assembly onto the wall plate.
Before hanging TV, please conduct "wall plate installation integrity test" first.
100 LBS (45 KG)
Tighten
TV must be hung up
by two person
Loosen the
pre-assembled
screws
A-3
A-2
Ø7/32 in
Ø5.5 mm
2 ¾ in (70mm)
Deep
Bit
Wood Stud
DANGER
Drill pilot holes using a
Ф7/32 in (Ф5.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes
or electrical wires are located. Be sure to
drill into the center of the stud.
A-1
Locate your studs. Verify and mark
the center of the stud by finding the
stud edges using awl and stud finder.
Min. 2"
(51mm)
Min. 4"
(102mm)
Center line
Wall in front of
the wood studs
< 16mm (5/8")
Attach Wall Plate to Wall
3-A
OPTION A:
Wood Stud Installation
CAUTION: Do not use
in drywall or wood stud!
B-3
B-2
Drill pilot holes using a
Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes
or electrical wires are located, or mortar
between blocks.
B-1
Attach Wall Plate to Wall
3-B
OPTION B:
Solid Concrete Wall Installation
Mounting Template
T3
Min. 8"
(203mm)
T1
Bubble Level
Level the mounting
template and mark the
pilot hole locations.
Contact us to have these
additional pieces shipped
directly to you.
Ф10×61mm
Concrete Wall Anchor
(NOT INCLUDED)
2 ¾ in (70mm)
Ф3/8in
Ф10 mm
Deep
Bit
Concrete Wall
002862.eps
DANGER
01
02
01
02
01
Line up the holes with your stud
center line. Level the mounting
template and mark the pilot hole
locations.
T1
Bubble Level
T3
Mounting Template
UP
UP
Install wall plate using lag bolts with Socket Wrench, NO Electrodrill.
No anchors when installed onto the wood studs.
AInstall wall plate using lag bolts and anchors (not included) with Socket
Wrench, NO Electrodrill.
A
A
A
Use the hammer to knock anchors (not included) into the concrete wall. Be sure
the anchors are seated flush with the concrete surface.
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of
the wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step. To prevent the TV falling down, the
Arrow Must Keep UP at this step!!
A
CAUTION:
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of
the wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step. To prevent the TV falling down, the
Arrow Must Keep UP at this step!!
A
CAUTION:
5-2 Tilt Adjustment
1. Loosen the tilting nuts ×2.
2. Adjust TV to your desired angle.
3. Retighten the nuts to fix the intended angle.
-13°
+5°
5-3 Lock TV in Place / Unlock
5-1 Leveling Adjustment
If needed, TV can be leveled ±3 degrees via adjusting the 4 nuts with the wrench (B).
Loosen the nuts Level the TV Tighten the nuts
Adjustments
5
± 3°
B B
Lock:
Push your TV to the wall and
lock the arm to the plastic clamp.
Unlock:
Pull out your TV to release the
arm from the plastic clamp.
Loosen
B
Tighten
  • Page 1 1
  • Page 2 2

MOUNTUP MU0058 Installation guide

Brand
MOUNTUP
Model
MU0058
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents