Mounting Dream MD2413-KT User manual

Category
Flat panel wall mounts
Type
User manual
Please read this instruction carefully before installation
.
Fits for most 26-55 inches Plasma, LCD and LED TVs
.
Weight capacity: 27kg (60 LBS)
.
Installation option 1
(without extended arms):
Installation option 2
(with extended arms):
INSTALLATION INSTRUCTION
Configuration 1
Configuration 2
Thank you for purchase! We strive to provide products and services of exceptional quality.
We sincerely invite you to write an unbiased review. For parts missed or installation problems,
please contact us at telephone (626) 604-9048 (USA) Mon - Fri 10am - 6pm (Pacific time) or email
us by customerservice@mountingdream.com, so that we may solve the issue for you.
(A1)
VESA:
300X300 mm
/11.81X11.81"
400x400 mm
/16X16"
VESA:
400X200 mm
/16X7.87"
VESA:
100X100 mm/4X4"
200X100 mm/7.87X4"
200X200 mm/7.87X7.87"
MODEL
MD2413-KT TV wall mount
US
WARNING!
安全警告
:
使
MD2413-KT
,预
防自身及其它人员遭遇危险并防止财产受损,在使用前请仔细阅读此手册,如果您不理解这些
说明或对安装的安全性有任何疑问,请致电有资格的承包商或与空中视界客户服务部联系。组
装前请仔细检查以确保零件无缺少或缺陷,我们的客户服务代表会迅速为您的安装问题提供协
助,以解决零件的缺少或缺陷问题。通过授权经销商所购产品的替换零件将直接送货上门。切
勿使用有缺陷的零件,安装不正确可能会导致产品损坏或者身体严重受伤。切勿将本产品用于
空中视界未明示的任何其它目的,公司对于安装不正确、装配不正确或使用不当造成的产品损
坏和身体受伤不承担任何责任。
CN
警告!
ADVERTENCIA!
AVERTISSEMENT!
SECURITY ALERT: welcome to use the horizon air TV rack. To ensure safe use of MD2413-KT TV rack
models, the prevention of its own and other people at risk and to prevent damage to property, please read
before using this manual carefully, if you do not understand these instructions or safety of the installation of
any questions, please call a qualified contractor or contact the customer service department of air horizon.
Please double-check to make sure that no missing or defective parts prior to assembly, our customer service
representatives can quickly assist your installation problems, to solve the missing parts or defects. Products
purchased through authorized dealers of replacement parts will be directly delivered to your door. Never use
defective parts, improper installation may result in product damage or serious bodily injury. Any other purpose
Never use this product for air horizon unspecified, the company is not installed correctly, incorrectly
assembled or product damage caused by improper use of bodily injury and does not bear any responsibility.
ALERTE DE SECURITE: bienvenue à utiliser la grille horizon air TV. Pour garantir une utilisation sûre des
modèles en rack TV MD2413-KT, la prévention de ses propres et d'autres personnes à risque et de prévenir les
dommages à la propriété, lisez s'il vous plaît avant d'utiliser ce manuel attentivement, si vous ne comprenez pas
ces instructions ou la sécurité de l'installation de tout questions, s'il vous plaît appeler un entrepreneur qualifié ou
contacter le service à la clientèle de l'horizon de l'air. S'il vous plaît double-vérifiez qu'aucune pièce manquante
ou défectueuse avant l'assemblage, nos représentants du service à la clientèle peuvent aider rapidement vos
problèmes d'installation, de résoudre les pièces ou les défauts manquants. Les produits achetés par des
courtiers autorisés de pièces de rechange seront livrés directement à votre porte. Ne jamais utiliser de pces
défectueuses, une installation incorrecte peut entraîner des dommages du produit ou des lésions corporelles
graves. Tout autre objectif Ne jamais utiliser ce produit pour horizon d'air non spécifié, la société n'a pas été
installé correctement, mal assemblé ou endommagement du produit causé par une mauvaise utilisation des
lésions corporelles et ne porte aucune responsabilité.
AVISO DE SEGURIDAD: recepción a usar el estante horizonte de aire de TV. Para garantizar un uso seguro de
los modelos de rack de TV MD2413-KT, la prevención de sus propios y otras personas en situación de riesgo y
para evitar daños a la propiedad, por favor leer antes de utilizar este manual cuidadosamente, si usted no
entiende estas instrucciones o la seguridad de la instalación de cualquier pregunta, por favor llame a un
contratista calificado o ponerse en contacto con el departamento de servicio al cliente de horizon Air. Vuelve a
comprobar para asegurarse de que no hay partes faltantes o defectuosas antes del montaje, nuestros
representantes de servicio al cliente pueden ayudar rápidamente sus problemas de instalación, para resolver los
defectos o partes que faltan. Los productos adquiridos a través de distribuidores autorizados de piezas de
recambio serán entregados directamente a su puerta. Nunca utilice piezas defectuosas, una instalación
incorrecta puede provocar daños o lesiones corporales graves. Cualquier otro propósito Nunca use este
producto para el horizonte de aire no se especifica, la empresa no se ha instalado correctamente, mal montados
o daños al producto causado por el uso indebido de daños corporales y no tiene ninguna responsabilidad.
FR
ES
Before getting started, let's make sure this mount is
perfect for you!
2
Does your TV (including accessories) weigh more than
60 lbs (27kg)?
60 lbs
(27kg)
NO --- Perfect!
Yes --- This mount is NOT compatible.
3
What is your wall made of?
CAUTION:
DO NOT install
into drywall alone
Perfect!
Drywall with
wood studs?
Solid concrete wall?
Perfect!
If this mount is NOT compatible, please contact
customerservice@mountingdream.com to find a compatible mount.
1
Is your TV VESA 100x100mm, 200x100mm, 200x200mm,
300x300mm, 400x200mm or 400x400mm?
Yes --- Perfect!
No --- This mount is NOT compatible.
MAX:400mm/16"
MAX:
400mm/16"
Wall mounting and TV bracket assembly hardware:
Installation tools:
Band tape
2m
Pencil
Screwdriver
Hammer
Electrodrill
2M
Installation tools:
-Wall plate unit
1pc
-Extended arm
2pcs
Band tape
2m
Pencil
Hammer
Electrodrill
2M
1
Part list
Stud finder
Bubble level
For parts shortage or damage, please contact us directly by
customerservice@mountingdream.com.
New delivery
will be timely
arranged to replace missed or defective parts.
Attention:
Gifts
-Extended arm
2pcs
Socket wrench
1/2"(13mm)
--Lag bolt
4pcs
--M8
Washer 4pcs
--4mm Allen key
1pc
--M6X8
Bolt 8pcs
--M6X12 Bolt
2pcs(pre-assembled)
3/8"
Masonry Drill Bit
7/32"
Wood Drill Bit
Velcro cable tie
3pcs
HDMI cable
1pc
Triangle Bubble level
1pc
Installation instruction
Wall plate
TV plate
g--M6X35 bolt
4pcs
f--M5X30 bolt
4pcs
e--M4X30 bolt
4pcs
h--M8X50 bolt
4pcs
TV mounting hardware:
c--M6X12 bolt
4pcs
b--M5X12 bolt
4pcs
a--M4X12 bolt
4pcs
d--M8X25 bolt
4pcs
Step 1
Remove the bolts with Allen key to separate wall plate
unit into two pieces.
2
k--M5/M4
washer 4pcs
i--M5/M6 spacer
4pcs
l--M6 washer
4pcs
j--M8 spacer
4pcs
m--10mm spacer
4pcs
n--2.5mm spacer
8pcs
Contact us at telephone (626) 604-9048 (USA) Mon - Fri 10am - 6pm (Pacific
time) or email us by customerservice@mountingdream.com to have these
additional pieces shipped directly to you.
Concrete Wall Anchor
4pcs
Concrete wall anchor (NOT INCLUDED)
drywall with
wood stud
The wall plate fits for single wood stud installation.
Step 2 Wall plate installation
:
Option 1 Wall plate installation in wood stud
To avoid potential body injury or property damage:
1. Wall mount must be installed into wood stud's center, not drywall alone.
2. Drywall covering the wood stud must not exceed 16 mm (5/8 in.).
3. Minimum wood stud size: common 2 x 4 in(51 x 102 mm). Nominal 1 1/2 x 3 1/2 in(38 x 89mm)
4. The wall must be capable of supporting five times the weight of TV plus mount.
5. Make sure the BOLT HEAD on the wall plate is upward as the picture shows.
6. All lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Failure to follow this instruction will possibly lead to TV falling off from wall, and would possibly
cause body injuries or property loss.
CAUTION
<16 mm(5/8 in.)
Locate the stud
with stud finder. Make
marks at the edges
of stud.
Mark centerlines
of stud.
Make sure the BOLT HEAD on the wall plate is upward
3
Then place wall plate along the centerline and use
pencil to mark 3 center holes locations on the wall.
7/32"
Use or 7/32" diameter drill bit
to drill 3 pilot holes at marked
positions to a depth of 2.5".
Put 3 lag bolts through the washers into the
drilled holes, and tighten each bolt by using a socket
wrench to mount the wall plate securely. Before totally
tightening the lag bolt please attach the bubble level
on the wall plate to check whether it is level.
center hole
center hole
Level
To avoid potential personal injury or property damage:
1. Make sure the BOLT HEAD on the wall plate is upward as the picture shows.
2. Solid concrete wall's thickness should be more than 100mm/4", and the wall must be
capable of supporting five times the weight of the TV plus the mount.
3. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Concrete wall
Option 2 Wall plate installation on concrete wall
CAUTION
Make sure the BOLT HEAD on the wall plate is upward
4
Level the wall plate and use wall plate as a
template and pencil to mark 4 side holes
locations on your desired height of the wall.
3/8"
Use 3/8" diameter drill bit to drill 4 holes
at marked positions to a depth of 2.5".
Put 4 Concrete Wall Anchors (not included in the package)
into drilled holes, and tap each anchor flush with the wall
by using a hammer. Then put 4 lag bolts through the
washers into the anchors, and tighten each bolt by
using a socket wrench to mount the wall plate securely.
Before totally tightening the lag bolt please attach the
bubble level on the wall plate to check whether it is level.
side holes
side holes
Level
1
Add distance to wall Irregular back Inset holes
Cables
Select TV hardware (diameter / length / combination)
Bolt diameter: hand thread bolts into threaded inserts on the back of
TV to determine correct bolt diameter (M4, M5, M6, M8).
Too Short
Bolt length: verify adequate thread engagement with bolts or
bolts/spacers combination. We recommend thread engagement
by at least 5 turns.
- Too short will not hold the TV.
- Too long will damage the TV.
Too Long
Correct
Bolt and spacer combination: spacers sometimes are needed to
combine with bolts for several situations.
+
(For detail bolts and spacers combination, please refer to Page 7 / 10)
2
3
TV back
TV back
TV back
TV back
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
Step 3
5
Step 4
Attach TV plate to the back of TV
Installation option 1:
If the VESA dimension is 100 mm x 100 mm(4 in x 4 in),
200 mm x 100 mm(7.87 in x 4 in) or 200 mm x 200 mm
(7.87 in x 7.87 in), take the following image as reference.
200mm
100mm
100mm
200mm
100mm
200mm
Attach TV plate to the back of TV directly:
For the TV with flat back, mount the TV plate with bolt/washer/spacer
combination.
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
6
Bolt/spacer/washer combination options
(only for reference)
Tips:You have to remove the inner
circle of 2.5mm washer (n) in order
to fit the M8 (d) bolt.
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
For TV with inset mounting holes, mount the TV plate with
bolt/washer/spacer combination.
(Spacers are highly recommended to be added, thus enlarge the
space between TV and brackets for better functionality.)
7
Bolt/spacer/washer combination options
(only for reference)
f
k
options
spacer
j
m
h
options
spacer
j
n
n
Tips: You have to remove the inner circle of 2.5mm washer (n) in order to fit the M6 (g)
or M8 (h) bolt.
Installation option 2:
If the VESA dimension is 400 mm x 200 mm(16 in x 7.87 in), attach
the extended arms ( , ) to the TV plate by screwing in bolts
with Allen key . Do not tighten the bolts at this step!
(see Configuration 1).
If the VESA dimension is 300 mm x 300 mm(11.81 in x 11.81 in) or
400 mm x 400 mm(16 in x 16 in) , attach the extended arms ( , )
to the TV plate by screwing in bolts with Allen key . Do not tighten
the bolts at this step! (see Configuration 2).
Configuration 2
R
L
400mm
400mm
300mm
300mm
L
R
Configuration 1
R
L
400mm
200mm
L
R
8
After the assembly of extended arms, attach the assembled plate to the
back of TV, then fasten the bolts tightly after align with the TV's
VESA holes. (Following steps only take Configuration 2 as example):
For the TV with flat back, mount the TV plate with bolt/washer/spacer
combination.
Carefully lay your TV on a non-abrasive surface, or lay itwith a padding underneath
it so as not to damage the screen.
9
Bolt/spacer/washer combination options
(only for reference)
Tips:You have to remove the inner
circle of 2.5mm washer (n) in order
to fit the M8 (d) bolt.
For TV with inset mounting holes, mount the TV plate with
bolt/washer/spacer combination.
(Spacers are highly recommended to be added, thus enlarge the
space between TV and brackets for better functionality.)
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
10
Bolt/spacer/washer combination options
(only for reference)
f
k
options
spacer
j
m
h
options
spacer
j
n
n
Tips: You have to remove the inner circle of 2.5mm washer (n) in order to fit the M6 (g)
or M8 (h) bolt.
Step 6
Hang the pre-assembled TV unit on the wall plate.
(Below images only show the TV plate with extended
arms--Configuration 2).
Step 5
Make sure the TV unit is horizontal, you can adjust the TV
plate a little bit (+/-5 degrees) to level the TV, then fasten
TV plate by bolts with Allen key .
Two people are recommended
to hold and position the TV .
Attention: Cables are
highly recommended to
plug in before hanging
the TV on the wall plate.
Tip: If TV still not level after adjustment, please loosen bolts a bit, hold
TV to adjust to level, then fasten bolts securely with Allen key.
11
±5°
Adjustment of tilting and swivel angles
Adjust the tilting angle (
+
5/-15°)
:
You may need to loosen the bolt with Allen key to adjust TV to
your desired angle. Please remember to fasten the bolt tightly
after adjustment.
Step 7
Manage TV cables orderly and tie them with velcro cable
ties.
Step 8
Adjust the swivel angle(±90°):
Grab the sides of the TV with two hands and slide the TV in the
desired direction until it is in your desired angle.
12
+5°
-15°
±5°
±90°
If you have any questions about the installation, please feel free to contact us at telephone (626) 604-9048 (USA)
Mon - Fri 10am - 6pm (Pacific time) or email us by customerservice@mountingdream.com .
For more information, please visit our website:www.mountingdream.com
Product dimensions:
13
MAX:400mm
MIN:100mm
435mm
MAX:400mm
MIN:100mm
435mm
484mm 74mm
+5°
-15°
+90°/-90°
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Mounting Dream MD2413-KT User manual

Category
Flat panel wall mounts
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages