PERLESMITH PSLFK3 Installation guide

English ------------------------ 1-9

Deutsch ------------------------ 10-18

Français------------------------ 19-27

Español ------------------------ 28-36

Italiano ------------------------ 37-45

PSLFK3

V1.0

LARGE FULL-MOTION TV WALL MOUNT

Thank you for choosing our product! We strive to provide the best quality and

services for our customers. Would you kindly share your experience on Amazon if

you are satisﬁed? Should you have any issues, please don't hesitate to contact us.

Telephone：800-5566-806 Mon-Fri 10am - 6pm (PST) (USA)

Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)

Tools Needed

Hammer

P1

Getting Started

WARNING:

Exceeding the weight capacity can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the weight of the TV (with

accessories) does not exceed 60 kg.

WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER

INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.

If you do not understand the instructions or have any concerns or questions, please contact a

qualified installer.

Do not install or assemble if the product or hardware is damaged or missing. Not all parts and

hardware included must be used. If you require replacement parts, contact customer service at

[email protected]

This product has been designed for use on a vertical wall constructed of wood studs. Wood studs

being defined as a wall consisting of a minimum of 2” x 4” studs with a maximum of 16” stud

spacing with a maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations

please contact a qualified installer. For safe installation, the wall you are mounting to must support

4 times the weight of the total load. If not, the surface must be reinforced to meet this standard.

The installer is responsible for verifying that the wall structure/surface will safely support the total

load.

This product may contain moving parts. Use with caution.

DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.

Please check www.perlesmith.com for more products and company information.

Stud

Finder

Tape

measure

1/2 in.

(12.7 mm)

7/32 in.

(5.5 mm)

Wood Drill

Screw

driver

Pencil Level

(included

inside the box)

Drill

3/8 in.

(10 mm)

Concrete Drill

CAUTION!

!

60 kg

MAXIMUM WEIGHT CAPACITY

P2

Arm and

Wall Plate

TV Brackets

Arm Extensions

Hardware Included

01

x1

03

x2

Front Support

End Caps

02

x1

05

x1

04

x2

Hardware Wall /Product)

5/16 x 2½ in

Lag Bolts

x4

Wall

Anchor

x4

DA

Washers

Ø8mm

Allen Wrench

x4

B

This product contains

small items that could be a choking hazard if

swallowed. Before starting assembly, verify

all parts are included and undamaged. If

any parts are missing or damaged, do not

return the damaged item to your dealer;

please contact our customer service team.

Never use damaged parts!

NOTE: Not all parts and hardware included

will be used.

WARNING:

x1

C

Philips Screws

M6 x 15mm

M6 x 30mm

Philips

Screws

M6 x 50mm

Washers

Ø6mm

M4-5-6

Spacers

L10mm

x4x4

Philips Screws

M8 x 15mm

M8 x 45mm

x4

x4 x8 x4

M-DM-A M-B

x4

M-C

M-E

Philips

Screws

M8 x 65mm

x4

M-F M-G

M-H

Spacers

L5mm

x8

M-I

TV Screws / Washers

STEP 1-1 Select TV

Screw Diameter

P3

Thread screws by hand into the threaded holes on the back of your TV to select which screw

diameter fits your TV.

M6

M8

STEP 1-2 Select TV

Screw Length

Correct

Too Long

Too Short

Measurement

200mm~600mm

7.9”~23.6”

100mm~400mm

3.9”~15.7”

?

P4

STEP 1-3

Attach the TV Bracket

(a) Flat Back

04

Position your TV brackets over your TV hole pattern - making sure the brackets are centered

and level over the TV hole pattern.

Secure the brackets using your screw/washer/spacer selection:

(a) for Flat Back

(b) for Round Back / Extra space

CAUTION: Ensure TV bracket is securely fastened before moving on to the next step.

04

(b) Round Back /

Extra Space

M-A M-D

M-H

M-B

M-C

M-F M-E

M-H

M-G M-I

STEP 2A

Wall Plate Installation (Concrete or brick)

CAUTION:

Avoid potential personal injury

or property damage! All lag bolts

A

MUST BE

firmly tightened to prevent unwanted movement

of the wall plate

01

.

CAUTION: Ensure the wall plate is securely fastened to the wall before continuing

on to the next step.

2A-1

01

Position the

wall plate

at your

desired

height , level

the wall plate

and mark the

pilot hole

locations.

Drill pilot

holes

2A-2

2A-3

01

A

B

D

01

Concrete Wall

D

01

A

DB

01

Install wall plate using lag bolts

and washer and anchor .

Tighten the lag bolts until they are

pulled firmly against the wall plate

A

UP

P5

2.75in 70 mm

Ø 10 mm

STEP 2B

Wall Plate Installation (Wood stud)

CAUTION:

Avoid potential personal injury

or property damage! All lag bolts

A

MUST BE

firmly tightened to prevent unwanted movement

of the wall plate

01

.

CAUTION: Ensure the wall plate is securely fastened to the wall before continuing

on to the next step.

2B-1

2B-2

● Drywall covering the wall must not exceed 5/8 in. (16 mm)

● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)

Locate your studs. Verify and

mark the center of the studs by

finding the stud edges using an

awl, a thin nail, or an

edge-to-edge stud finder.

Position the wall plate at

your desired height and line up

the holes with your stud center

line. Level the wall plate and

make the holes.

UP

01

P6

01

2B-3

7/32 in.

Ø5.5 mm

in. (70 mm)

Drill pilot holes using a 7/32 in. (5.5 mm)

diameter drill bit.

IMPORTANT:

Pilot holes must be

in. (70 mm).

Be sure to drill into the center of the stud.

drilled to a depth of

2B-4

A

2

01

A

B

01

Install wall plate using lag bolts

and washer . Tighten the lag bolts

until until they are pulled firmly against

the wall plate

A

STEP 3

Install Front support [02] and extensions [03] and End cap [05] together.

Install the extensions [03] to Front support [02] withe the pre-assembled screws.

02 03 05

P7

01

B

UP

3-1

3-2

Pre-assembled scews

Finished

02

03

05

P8

3-3

STEP 4

Hang TV with

brackets

04

onto the

arm

extensions

02

and

03

.

S1

Hang 02 onto 01 and using a screwdriver, secure with preassembled screws

S1

S2

01

02

04

03

02

Remove the

preassembled

screws [S2] and

save to use, then

raise the safety

locks.

Press the safety locks

then fasten the removed

screws [S2].

01 02 03

P9

[S1]

TO ADJUST TV LEVEL, loosen the two screws [S1] on the

rear of the arm plate, adjust level, and retighten to secure.

To adjust the tilt in both sides, loosen both tilt nuts and move panel to

desired position. Tighten both tilt nuts to hold desired tilt.

TIGHTEN

C

LOOSEN

C

TIGHTEN

± 3°

Page is loading ...

PERLESMITH PSLFK3 Installation guide

PERLESMITH PSLFK3 Installation guide

in other languages

Related papers

Other documents