Topcon SL-100 User manual

Brand: Topcon

Model: SL-100

Category: GPS receiver modules

Type: User manual

This manual is also suitable for

MC-i3

Hardware Setup, Settings, Pinout, SL-R3 Firmware

Upgrade, GNSS Firmware Upgrade

MC-i3 and SL-100

MC-I3 and SL-100

Topcon Europe Positioning

• Rugged Housing for

Construction Environment

• Ingress Protection:IP-67

• Network RTK Connectivity

• Input Voltage: 9 – 32 V DC

• Operating Temp:-30

o

C to+70

o

C

Features: SL-100/MC-i3

• New Indicate MC receiver

• Vanguard™ Technology

• Internal SL-R3, Dig UHFII

• Single or Dual GPS configurations

• 2 Deutsch connectors  serial and

Ethernet to

GX-60 or GX-30

• TNC connectors for radio and GPS

antenna

Dip Switch Settings

Install SIM Card

SL-R3 Antenna

Hardware setup

Hardware

MC-i3 / SL-100 Main B

PC ethernet

connection

Contains:

1001270-01 Ethernet Cable to configure SL-R3

MC-i3 / SL-100 Data cable kit 1001271-01

MC-i3 / SL-100 Data cable kit 1001271-01

Power

Serial 1 – (Main board)

Serial 2 (Aux board)

Contains:

1001269-01 Serial Cable to configure GPS boards

MC-i3 / SL-100 Main A

Connectors pin outs

How to enter the SL-R3 to change settings.

• GX-60 or Computer

• Take 1001269-01 cable to power up the box

only.

• Use 1001270-01 cable for tcp/ip connection to

slr-3

Connect ethernet and powerup the mci3 and follow the steps below.

In “control panel” “network and sharing center” use the “local area connection”

Set Computer Ethernet Port to match with right picture.

Type 192.168.0.1 in your browser( chrome or QT web browser will do)

When prompted for the user name and password,

enter ”admin” for both and click “ok”

Check SL-R3 Firmware

SLR-3 Firmware update:

Select the download of latest firmware release and reboot after loading.

2

3

1

4

Configure SIM Card

Go to settings/ports/gprs

ATD*99***1#

After save all settings Reboot

Check connections and GSM status.

GNNS Firmware update MC-i3 via SLR-3

- Use GX-60 or PC

- Use cable 1001269-01 Power & Serial Cable’s

- Use 1001270-01 cable for tcp/ip connection to slr-3

- Follow procedure described in next slides.

MC-i3 GNNS FW update via GX-60 or PC

Please select serial port 1 and 2 to function with GPS and save

MC-i3 GNNS FW update via GX-60 or PC

Primary GPS

uncheck “Enabled” to disable

gps communication to SLR3.

In case of dual GPS:

Secondary GPS

uncheck “Enabled” to disable

when you update the firmware

for this card too.

Save this and go to

Firmware Upgrade tab.(next slide)

After update and reboot tick “Enabled” in the configuration tab again to

restart using the gps communication to the SLR-3 .(do not forget!)

Page is loading ...

Page is loading ...

Page is loading ...

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

Topcon SL-100 User manual

Brand: Topcon

Model: SL-100

Category: GPS receiver modules

Type: User manual

This manual is also suitable for

MC-i3

Download PDF

Related papers

Other documents