H3C SR6600 SPE-FWM User manual

H3C SR6600/SR6600-X Routers

Interface Module Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W106-20150618

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of

Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

i

Contents

Interface modules ························································································································································· 1

HIMs ··················································································································································································· 1

HIM-8FE (RT-HIM-8FE-H3) ········································································································································ 1

HIM-4GBE (RT-HIM-4GBE-WAN-H3)/HIM-8GBE (RT-HIM-8GBE-WAN-H3) ····················································· 2

HIM-4GBP (RT-HIM-4GBP-H3)/HIM-8GBP (RT-HIM-8GBP-H3) ············································································ 4

HIM-1EXP (RT-HIM-1EXP-H3) ··································································································································· 7

HIM-CL1P (RT-HIM-1CPOS/STM1-H3)/HIM-CL2P (RT-HIM-2CPOS/STM1-H3) ················································ 8

HIM-CLS1P (RT-HIM-CLS1P-H3)/HIM-CLS2P (RT-HIM-CLS2P-H3) ····································································· 10

HIM-MSP2P (RT-HIM-MSP2P-H3)/HIM-MSP4P (RT-HIM-MSP4P-H3) ································································ 13

HIM-PS1P (RT-HIM-1POS/STM16-H3) ················································································································ 15

HIM-AL1P (RT-HIM-AL1P-H3)/HIM-AL2P (RT-HIM-AL2P-H3) ·············································································· 17

HIM-RS2P (RT-HIM-RS2P-H3) ································································································································ 19

HIM-4G4P (RT-HIM-4G4P-H3) ····························································································································· 21

HIM-TS8P (RT-HIM-TS8P-H3) ································································································································· 23

HIM-8GBP-V2 ························································································································································· 26

HIM-16GBP ···························································································································································· 28

HIM-2EXP ······························································································································································· 29

MIMs················································································································································································ 31

MIM-2GBE (RT-MIM-2GBE-H3) ···························································································································· 31

MIM-8E1(75)(RT-MIM-8E1(75)-H3)/MIM-8E1(75)-F(RT-MIM-8E1(75)-F-H3) ·················································· 32

MIM-8T1/MIM-8T1-F RT-MIM-8T1-H3)/MIM-8T1-F (RT-MIM-8T1-F-H3) ·························································· 34

MIM-1CE3(RT-MIM-1CE3-V2-H3) ························································································································ 36

MIM-1CT3 (RT-MIM-1CT3-V2-H3) ······················································································································· 37

MIM-2SAE (RT-MIM-2SAE-H3)/MIM-4SAE (RT-MIM-4SAE-H3)/MIM-8SAE (RT-MIM-8SAE-H3) ·················· 39

SAPs ················································································································································································· 42

SAP-48GBE (RT-SAP-48GBE-H3) ························································································································· 42

SAP-24GBP (RT-SAP-24GBP-H3) ·························································································································· 44

SAP-48GBP (RT-SAP-48GBP-H3) ·························································································································· 46

SAP-4EXP (RT-SAP-4EXP-H3) ································································································································· 49

SAP-20GE2XP ························································································································································ 51

SAP-28GE ······························································································································································ 55

Connecting interface cables ······································································································································ 59

Connecting an Ethernet interface cable ······················································································································· 59

Connecting an optical interface cable ························································································································· 60

Connecting an E1 interface cable ································································································································ 62

Connecting a T1 interface cable ·································································································································· 65

Connecting a CE3/CT3 interface cable ····················································································································· 66

Connecting a serial interface cable ····························································································································· 67

Compatibility matrixes ··············································································································································· 70

Compatibility matrixes on Comware V5 ····················································································································· 70

LPU and router compatibility matrix ···················································································································· 70

LPU and MPU compatibility matrix ······················································································································ 70

MPU and router compatibility matrix ·················································································································· 71

Compatibility matrixes on Comware V7 ····················································································································· 71

LPU and router compatibility matrix ···················································································································· 71

LPU and MPU compatibility matrix ······················································································································ 72

MPU and router compatibility matrix ·················································································································· 72

Interface module and FIP compatibility matrix ············································································································ 72

ii

Interface module&SAP and transceiver module compatibility matrix ······································································· 73

Index ··········································································································································································· 76

1

Interface modules

The SR6600/SR6600-X router supports hot swapping of interface modules.

NOTE:

The LPU, MPU, and router compatibility matrixes vary by Comware system. For more information, see

"Compatibility matrixes."

HIMs

HIM-8FE (RT-HIM-8FE-H3)

The HIM-8FE is a 10Base-T/100Base-TX Fast Ethernet (FE) interface module used by a router to

communicate with a LAN. It provides eight RJ-45 ports, each of which supports the Layer 3 routing

function and has a bi-color status LED.

The HIM-8FE has the following features:

• The transmission distance can be up to 100 meters (328.08 ft) if a category-5 twisted pair cable is

used.

• The interfaces support 10/100 Mbps auto-sensing.

• The interfaces typically operate in full duplex mode and can also operate in half duplex mode.

Front panel

Figure 1 Front panel

(1) FE port (2) FE port

status LED

(3) Captive screw (4) Ejector lever

2

LEDs

Table 1 LED description

LED status Descri

p

tion

Off

No link is present or the cable is faulty.

Steady yellow

A 10 Mbps link is present.

Flashing yellow

Data is being received or transmitted at 10 Mbps.

Steady green

A 100 Mbps link is present.

Flashing green

Data is being received or transmitted at 100 Mbps.

Interface specifications

Table 2 Interface specifications

Item S

p

ecification

Connector type

RJ-45

Number of interfaces

8

Interface standards 802.3, 802.3u

Interface type

Auto MDI/MDI-X

Cable type

Straight-through/crossover cable

Transmission distance 100 m (328.08 ft)

Interface speed and duplex mode

• 10/100 Mbps auto-sensing

• Full duplex/half duplex

NOTE:

The medium dependent interface (MDI) standard is typically used on the Ethernet interface of network

adapters; the medium dependent interface crossover (MDI-X) standard is typically used on hubs or LAN

switches.

Interface cables

The HIM-8FE uses a category-5 straight-through cable or crossover Ethernet cable. For the appearance

and connection of a HIM-8FE interface cable, see "Connecting an Ethernet interface cable."

HIM-4GBE (RT-HIM-4GBE-WAN-H3)/HIM-8GBE

(RT-HIM-8GBE-WAN-H3)

The HIM-4GBE and HIM-8GBE are 10Base-T/100Base-TX/1000Base-T auto-sensing Ethernet interface

modules. A HIM-4GBE provides four, and a HIM-8GBE provides eight, RJ-45 ports that support Layer 3

routing. Each port is provided with a bi-color LED indicating the running status of the port. The HIM-4GBE

or HIM-8GBE is connected to the processor through a 10-Gbps high-speed bus and can provide all

high-performance Layer 3 Ethernet interface functionalities.

3

Front panels

Figure 2 Front panel of HIM-8GBE

(1) GE port (2) GE port status LED

(3) Captive screw (4) Ejector lever

Figure 3 Front panel of HIM-4GBE

(1) Captive screw (2) GE port

(3) GE port status LED (4) Ejector lever

LEDs

Table 3 LED description

LED status Descri

p

tion

Off No link is present or the cable is faulty.

Steady green A 1000 Mbps link is present.

Flashing green Data is being received or transmitted at 1000 Mbps.

Steady yellow A 10/100 Mbps link is present.

Flashing yellow Data is being received or transmitted at 10/100 Mbps.

1

2 3

4

Interface specifications

Table 4 Interface specifications

Item S

p

ecification

Connector type RJ-45

Number of interfaces

• HIM-4GBE: 4

• HIM-8GBE: 8

Interface standards 802.3, 802.3u, 802.3ab

Interface type Auto MDI/MDI-X

Cable type Straight-through/crossover Ethernet cable

Transmission distance 100 m (328.08 ft)

Supported frame format

• Ethernet_II

• Ethernet_SNAP

Interface speed and duplex mode

10 Mbps Full/half duplex, auto-negotiation

100 Mbps Full/half duplex, auto-negotiation

1000 Mbps Full duplex

NOTE:

• When 10/100 Mbps and half duplex/full duplex are specified for an Ethernet copper port, the Etherne

t

copper port operates in forced mode. When 1000 Mbps is specified or the interface speed and the

duplex mode are not simultaneously specified for an Ethernet copper port, the port operates in

auto-negotiation mode.

• When operating in forced mode, an Ethernet copper port does not support auto MDI/MDI-X.

• When operating in auto-negotiation mode, an Ethernet copper port supports auto MDI/MDI-X.

Interface cables

The HIM-4GBE/HIM-8GBE uses a category-5 straight-through or crossover Ethernet cable when

operating at 10/100 Mbps, and uses a category-6 cable (recommended) when operating at 1000

Mbps. For the appearance and connection of a HIM-4GBE/HIM-8GBE interface cable, see

"Connecting an Ethernet interface cable."

HIM-4GBP (RT-HIM-4GBP-H3)/HIM-8GBP (RT-HIM-8GBP-H3)

The HIM-4GBP and HIM-8GBP are high-speed Layer 3 GE interface modules. A HIM-4GBP provides 4,

and a HIM-8GBP provides 8 Small Form-Factor Pluggable (SFP) ports that support Layer 3 routing. Each

port is provided with a bi-color LED, which indicates the running status of the port. Connected to the

processor through an SPI-4 high-speed bus, the HIM-4GBP or HIM-8GBP provides a full range of

high-performance functions of Layer 3 Ethernet interfaces.

5

Front panels

Figure 4 Front panel of HIM-4GBP

(1) Captive screw (2) SFP port

(3) SFP port status LED (4) Ejector lever

Figure 5 Front panel of HIM-8GBP

(1) Captive screw

(2)

SFP

port

(3) SFP port status LED (4) Ejector lever

LEDs

Table 5 LED description

LED status Descri

p

tion

Off No link is present.

Steady green A 1000 Mbps link is present.

Flashing green The interface is receiving or sending data at 1000 Mbps.

Steady yellow A 100 Mbps link is present.

Flashing yellow The interface is receiving or sending data at 100 Mbps.

6

Interface specifications

Table 6 Interface specifications

Item S

p

ecification

Connector type SFP

Number of interfaces

• HIM-4GBP: 4

• HIM-8GBP: 8

Interface standards 802.3, 802.3u, 802.3ab

Supported frame

format

• Ethernet_II

• Ethernet_SNAP

Transmis

sion

power

Type Short distance

Medium

distance

Long distance

Ultra-long

distance

Min. –9.5 dBm –9 dBm –2 dBm –4 dBm –4 dBm

Max. 0 dBm –3 dBm 5 dBm 1 dBm 2 dBm

Receiving sensitivity –17 dBm –20 dBm –23 dBm –21 dBm –22 dBm

Central wavelength 850 nm 1310 nm 1310 nm 1550 nm 1550 nm

Fiber type

62.5/125 m

multi-mode

fiber

9/125 m

single-mode

fiber

9/125 m

single-mode

fiber

9/125 m

single-mode

fiber

9/125 m

single-mode

fiber

Max. transmission

distance

0.55 km

(0.3418 miles)

10 km (6.21

miles)

40 km (24.86

miles)

40 km (24.86

miles)

70 km (43.50

miles)

Interface speed

• 1000 Mbps (recommended)

• Full duplex

The following transceiver modules are available for the HIM-4GBP/HIM-8GBP:

• 100 Mbps fiber SFP transceiver modules.

• 1000 Mbps fiber SFP transceiver modules.

• 100/1000 Mbps fiber SFP transceiver modules.

• 10/100/1000 Mbps copper SFP transceiver modules (support for 10/100/1000 Mbps

autosensing on the HIM-4GBP/HIM-8GBP).

Prepare the transceiver modules yourself as required.

H3C recommends that you use H3C SFP transceiver modules for the device. H3C does not guarantee the

compatibility of SFP transceiver modules from other vendors with the device. The device reports an alarm

when non-H3C SFP transceiver modules are installed.

Interface cables

Use interface cables for the HIM-4GBP/HIM-8GBP as follows:

• Fiber SFP transceiver module—Fibers with the LC connector.

• Copper SFP transceiver module—Category-5 straight-through or crossover twisted pair cable when

the port is operating at 10/100 Mbps and Category-6 twisted pair cable when the port is

operating at 1000 Mbps.

For the appearance and connection of a HIM-4GBP/HIM-8GBP interface cable, see "Connecting an

Ether

net interface cable" or "Connecting an optical interface cable."

7

HIM-1EXP (RT-HIM-1EXP-H3)

The HIM-1EXP is a 1-port 10 GE transceiver module. It provides one 10-Gigabit Small Form-Factor

Pluggable (XFP) port and supports switchover between LAN/WAN PHY modes. A LED is provided on the

front panel to show the operation state.

Front panel

Figure 6 Front panel

(1) Captive screw (2) Ejector lever

(3) XFP port (4) XFP port carrier signal LED (LINK/ACT)

LED

Table 7 LED description

LED status Descri

p

tion

Off No link is present.

Steady green A link is present, but no data is being received or transmitted.

Flashing green The XFP port is receiving or sending data.

Interface specifications

Table 8 Interface specifications

Item S

p

ecification

Connector type XFP/LC

Number of interfaces 1

Supported frame format 10GBase-R/W

Interface speed

• LAN PHY mode: 10.3125 Gbps

• WAN PHY mode: 9.95328 Gbps

Optical transmit

power

Type Short distance Medium distance Long distance

Min. –7.3 dBm –8.2 dBm –1 dBm

Max. –1.08 dBm 0.5 dBm 2 dBm

8

Item S

p

ecification

Receiving sensitivity –7.5 dBm –10.3 dBm –11.3 dBm

Central wavelength 850 nm 1310 nm 1550 nm

Max. transmission distance 0.3 km (0.19 miles) 10 km (6.21 miles) 40 km (24.86 miles)

Fiber type

62.5/125 m

multi-mode

9/125 m single-mode

9/125 m

single-mode

NOTE:

In LAN PHY mode, 10GBase-R is supported. In WAN PHY mode, 10GBase-W is supported.

Interface cables

The HIM-1EXP must work with an XFP transceiver module and an optical fiber with LC-type connectors.

For the appearance and connection of a HIM-1EXP interface cable, see "Connecting an optical interface

ca

ble."

HIM-CL1P (RT-HIM-1CPOS/STM1-H3)/HIM-CL2P

(RT-HIM-2CPOS/STM1-H3)

The HIM-CL1P and HIM-CL2P are high-speed OC-3/STM-1 (155 Mbps) channelized packet over

SONET/SDH (CPOS) E1/T1 interface modules. The HIM-CL1P provides one SFP port and the port is

provided with two LEDs, which indicate the port running status and fault detection status, respectively. The

HIM-CL2P provides two SFP ports.

The HIM-CL1P/HIM-CL2P has the following features:

• Connects to the processor through a 10-Gbps high-speed bus. Each CPOS interface can be

channelized into 63 E1s or 84 T1s, and it can be channelized into 512 DS0s.

• Receives multiplexed E1/T1 circuits on a pair of fibers through a channelized interface, saving

many link resources, the occupied area, and the cost of local networks and devices for

telecommunication service providers and large enterprises.

• Supports IP and MPLS traffic and the Multi-link Point-to-Point Protocol (MP), and supports up to 12

E1s or T1s in each MP bundle.

• Uses hardware-based MP bundling. This solves the problem of low efficiency of MP bundling, and

improving the access density of user devices.

• Supports two operating modes that can be configured at the CLI: CPOS E1 and CPOS T1.

• The operating mode configuration takes effect only after you hot-swap the interface module or

reboot the device. H3C recommends that you remove and insert the module to bring the

configuration into effect.

• The operating mode configuration takes effect for all the interfaces on the interface module.

NOTE:

• The HIM-CL1P/HIM-CL2P does not support cascading and non-channelized SDH and SONET.

• The HIM-CL1P/HIM-CL2P does not support channelizing OC-3/STM-1 into DS3s or E3s.

9

Front panels

Figure 7 Front panel of HIM-CL1P

(1) SFP port carrier si

g

nal LED (LINK/ACT)

(2) SFP port loopback/alarm LED (LP/AL) of SFP port

(3) SFP port (4) Captive screw

(5) Ejector lever

Figure 8 Front panel of HIM-CL2P

(1) SFP port carrier si

g

nal LED (LINK/ACT) (2) SFP port loopback/alarm LED (LP/AL)

(3) SFP port (4) Captive screw

(5) Ejector lever

LEDs

Table 9 LED description

LED Status Descri

p

tion

LINK/ACT

(Green)

Off No link is present.

On A 155.52 Mbps link is present.

Flashing The SFP port is receiving or sending data at 155.52 Mbps.

LP/AL

(Yellow)

Off No loopback or alarm exists.

On The port is in loopback state.

Flashing There is a minimum of one alarm.

10

Interface specifications

Table 10 Interface specifications

Item S

p

ecification

Connector type SFP/LC

Number of interfaces

• HIM-CL1P: 1

• HIM-CL2P: 2

Interface standards SONET OC-3/SDH STM-1

Interface speed 155.52 Mbps

Optical

transmit

power

Type Short distance Medium distance Long distance

Ultra-long

distance

Min. –19.0 dBm –15.0 dBm –5.0 dBm –5.0 dBm

Max. –14.0 dBm –8.0 dBm 0 dBm 0 dBm

Receiving sensitivity –30.0 dBm –28.0 dBm –34.0 dBm –34.0 dBm

Overload optical power –14.0 dBm –7.0 dBm –9.0 dBm –10.0 dBm

Central wavelength 1310 nm 1310 nm 1310 nm 1550 nm

Max. transmission

distance

2 km (1.24 miles)

15 km (9.32 miles)

40 km (24.86

miles)

80 km (49.71

miles)

Fiber type

62.5/125 m

multi-mode

9/125 m

single-mode

9/125 m

single-mode

9/125 m

single-mode

Interface cables

The HIM-CL1P/HIM-CL2P must work with an SFP transceiver module and an optical fiber that have

LC-type connectors. For the appearance and connection of a HIM-CL1P/HIM-CL2P interface cable, see

"Connecting an optical interface cable."

HIM-CLS1P (RT-HIM-CLS1P-H3)/HIM-CLS2P

(RT-HIM-CLS2P-H3)

The HIM-CLS1P and HIM-CLS2P are high-speed OC-3/STM-1 (155 Mbps) CPOS E3/T3 interface

modules. They can also operate in packet over SONET/SDH (POS) mode. The HIM-CLS1P provides one

SFP port and the port is provided with two LEDs, which indicate the port running status and fault detection

status, respectively. The HIM-CLS2P provides two SFP ports.

The HIM-CLS1P/HIM-CLS2P has the following features:

• Connects to the processor through a 10-Gbps high-speed bus. Each OC-3/STM-1 POS interface

can be channelized into three E3s or T3s.

• Each E3/T3 channel supports the subrate processing capability, providing users with a variety of

bandwidth options.

• Receives multiplexed E3/T3 circuits on a pair of fibers through a channelized interface, saving

many link resources, the occupied area, and the cost of local networks and devices for

telecommunication service providers and large enterprises.

• Supports IP and MPLS traffic and MP with up to three E3s or T3s in each MP bundle.

11

• Supports three operating modes that can be configured at the CLI: CPOS E3, CPOS T3, or POS

(155 Mbps) .

• The configuration of the operating mode can take effect only after you hot-plug the interface module

or reboot the device. It is recommended to remove and insert the module to bring the configuration

into effect.

• The configuration of the operating mode takes effect for all the interfaces on the interface modules.

NOTE:

The HIM-CLS1P/HIM-CLS2P does not support channelizing OC-3/STM-1 into DS1s or E1s.

Front panels

Figure 9 Front panel of HIM-CLS1P

(1) Captive screw

(2)

Ejector lever

(3) SFP port (4) SFP port carrier signal LED (LINK/ACT)

(5) SFP port loopback/alarm LED (LP/AL)

Figure 10 Front panel of HIM-CLS2P

(1) Captive screw

(2)

Ejector lever

(3) SFP port (4) SFP port carrier si

g

nal LED (LINK/ACT)

(5) SFP port loopback/alarm LED (LP/AL)

12

LEDs

Table 11 LED description

LED Status Descri

p

tion

LINK/ACT

(Green)

Off No link is present.

On A 155.52 Mbps link is present.

Flashing The SFP port is receiving or sending data at 155.52 Mbps.

LP/AL

(Yellow)

Off No loopback or alarm exists.

On The interface is in loopback state.

Flashing There is a minimum of one alarm.

Interface specifications

Table 12 Interface specifications

Item S

p

ecification

Connector type SFP/LC

Number of interfaces

• HIM-CLS1P: 1

• HIM-CLS2P: 2

Interface standards SONET OC-3/SDH STM-1

Interface speed 155.52 Mbps

Optical

transmit

power

Type Short distance Medium distance Long distance

Ultra-long

distance

Min. –19.0 dBm –15.0 dBm –5.0 dBm –5.0 dBm

Max. –14.0 dBm –8.0 dBm 0 dBm 0 dBm

Receiving sensitivity –30.0 dBm –28.0 dBm –34.0 dBm –34.0 dBm

Overload optical power –14.0 dBm –7.0 dBm –9.0 dBm –10.0 dBm

Central wavelength 1310 nm 1310 nm 1310 nm 1550 nm

Max. transmission

distance

2 km (1.24 miles)

15 km (9.32 miles)

40 km (24.86

miles)

80 km (49.71

miles)

Fiber type

62.5/125 m

multi-mode

9/125 m

single-mode

9/125 m

single-mode

9/125 m

single-mode

Interface cables

The HIM-CLS1P/HIM-CLS2P must work with an SFP transceiver module and an optical fiber with LC-type

connectors. For the appearance and connection of a HIM-CLS1P/HIM-CLS2P interface cable, see

"Connecting an optical interface cable."

13

HIM-MSP2P (RT-HIM-MSP2P-H3)/HIM-MSP4P

(RT-HIM-MSP4P-H3)

The HIM-MSP2P/HIM-MSP4P is a high-speed OC-3/STM-1 (155 Mbps) and OC-12/STM-4 (622 Mbps)

non-channelized POS interface module. The HIM-MSP2P/HIM-MSP4P supports PPP, Frame Relay, and

HDLC at the data link layer and IP at the network layer.

When using the HIM-MSP2P/HIM-MSP4P, follow these guidelines:

• You can use the card-mode command to configure the interface module to operate in OC-3/STM-1

POS or OC-12/STM-4 POS mode.

• The configuration of the operating mode can take effect only after you hot-swap the interface

module or reboot the device. It is recommended to remove and insert the module to bring the

configuration into effect.

• The configuration of the operating mode takes effect for all the interfaces on the interface module.

• The interface module supports multi-mode short distance (1310 nm), single-mode medium distance

(1310 nm), single-mode long distance (1310 nm), and single-mode ultra-long distance (1550 nm)

transceiver modules.

NOTE:

The HIM-MSP2P/HIM-MSP4P is an optional interface module to be separately ordered if needed.

Front panels

Figure 11 Front panel of HIM-MSP2P

(1) Captive screw

(2) Ejector lever

(3) SFP port carrier si

g

nal LED (LINK/ACT)

(4) SFP port loopback/alarm LED (LP/AL)

(5) SFP port 1 (155 Mbps)/SFP port 0 (622 Mbps) (6) SFP port 0 (155 Mbps)

14

Figure 12 Front panel

(1) Captive screw (2) Ejector lever

(3) SFP port carrier si

g

nal LED (LINK/ACT)

(4) SFP port loopback/alarm LED (LP/AL)

(5) SFP port 3 (155 Mbps) or SFP port 1 (622 Mbps)

(6) SFP port 2 (155 Mbps) or SFP port 0 (622 Mbps)

(7) SFP port 1 (155 Mbps) (8)

SFP port 0 (155 Mbps)

LEDs

Table 13 LED description

LED Status Descri

p

tion

LINK/ACT

(Green)

Off No link is present.

On A 155.52/622.08 Mbps link is present.

Flashing The SFP port is receiving or sending data at 155.52/622.08 Mbps.

LP/AL

(Yellow)

Off No loopback or alarm exists.

On The port is in loopback state.

Flashing There is a minimum of one alarm.

Interface specifications

Table 14 Interface specifications

Item S

p

ecification

Connector type SFP/LC

Number of interfaces

• HIM-MSP2P: 2 OC-3 interfaces or 1 OC-12 interface

• HIM-MSP4P: 4 OC-3 interfaces or 2 OC-12 interfaces

Interface standards

• SONET STS-3/STS-12

• SDH STM-1/STM-4

Interface speed 155.52/622.08 Mbps

OC-3 interface (155.52 Mb

p

s)

Optical

Type Short distance Medium distance

Long distance Ultra-long distance

1

2

3

45678

15

Item S

p

ecification

Min. –19.0 dBm –15.0 dBm –5.0 dBm –5.0 dBm

Max. –14.0 dBm –8.0 dBm 0 dBm 0 dBm

Receiving sensitivity –30.0 dBm –28.0 dBm –34.0 dBm –34.0 dBm

Overload optical power –14.0 dBm –7.0 dBm –9.0 dBm –10.0 dBm

Central wavelength 1310 nm 1310 nm 1310 nm 1550 nm

Max. transmission

distance

2 km (1.24 miles)

15 km (9.32

miles)

40 km (24.86

miles)

80 km (49.71

miles)

Fiber type

62.5/125 m

multi-mode

9/125 m

single-mode

9/125 m

single-mode

9/125 m

single-mode

OC-12 interface (622.08 Mb

p

s)

Optical

transit power

Type Medium distance Long distance Ultra-long distance

Min. –15.0 dBm –3.0 dBm –3 dBm

Max. –8.0 dBm 2.0 dBm 2.0 dBm

Receiving sensitivity –28.0 dBm –28.0 dBm –28 dBm

Overload optical power –8.0 dBm –8.0 dBm –8 dBm

Central wavelength 1310 nm 1310 nm 1550 nm

Max. transmission

distance

15 km (9.32 miles) 40 km (24.86 miles) 80 km (49.71 miles)

Fiber type 9/125 m single-mode

9/125 m

single-mode

9/125 m single-mode

Interface cables

The HIM-MSP2P/HIM-MSP4P must work with an SFP transceiver module and an optical fiber with

LC-type connectors. For the appearance and connection of a HIM-MSP2P/HIM-MSP4P interface cable,

see "Connecting an optical interface cable."

HIM-PS1P (RT-HIM-1POS/STM16-H3)

The HIM-PS1P is a high-speed OC-48/STM-16 (2.5 Gbps) CPOS or non-channelized POS interface

module. It supports PPP, Frame Relay, and HDLC at the data link layer and IP at the network layer. It

provides POS interfaces for direct transmission of data packets over SONET/SDH.

When using the HIM-PS1P, follow these guidelines:

• The interface module can run in E-CPOS mode or OC-48/STM-16 POS mode.

• The interface module supports multi-mode short distance (1310 nm), single-mode medium distance

(1310 nm), single-mode long distance (1310 nm), and single-mode ultra-long distance (1550 nm)

transceiver modules.

The HIM-PS1P is an optional module to be separately ordered if needed.

16

Front panel

Figure 13 Front panel of HIM-PS1P

(1) Captive screw (2) Ejector lever

(3) SFP port carrier si

g

nal LED (LINK/ACT)

(4) SFP port loopback/alarm LED (LP/AL)

(5) SFP port (2.5 Gbps)

LEDs

Table 15 LED description

LED Status Descri

p

tion

LINK/ACT

(Green)

Off No link is present.

On A 2488.32 Mbps link is present.

Flashing The SFP port is receiving or sending data at 2488.32 Mbps.

LP/AL

(Yellow)

Off No loopback or alarm exists.

On The interface is in loopback state.

Flashing There is a minimum of one alarm.

Interface specifications

Table 16 Interface specifications

Item S

p

ecification

Connector type SFP/LC

Number of interfaces 1 OC-48 interface

Interface standards

• SONET STS-48

• SDH STM-16

Interface speed 2488.32 Mbps

Optical

transit

power

Type Short distance Medium distance Long distance

Ultra-long

distance

Min. –10.0 dBm –5.0 dBm –2.0 dBm –2.0 dBm

Max. –3.0 dBm 0 dBm 3.0 dBm 3.0 dBm

Page is loading ...

H3C SR6600 SPE-FWM User manual

This manual is also suitable for

H3C SR6600 SPE-FWM User manual

Related papers

Other documents