7.5” Round 13W LED Ceiling Disk Light Installation Guide
MCL-713705
www.maxximastyle.com
3 YEAR WARRANTY
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume
any obligation whatsoever beyond sending a free replacement product.
• Risk of electric shock or fire - Disconnect power at the source
before installation.
• If you are unsure about the installation or the maintenance
of the fixture, please consult an electrician.
• Do not make or alter any holes in the wiring enclosure or
modify any electrical componentry.
• To prevent wiring damage or abrasion, do not expose wiring
to edges of sheet metal or other sharp objects.
CAUTIONS
• The fixture must be wired in accordance with
the National Electric Code (N.E.C) standards and
any applicable local codes or ordinances.
• This fixture is designed for use with 120Vac, 50/60Hz only.
• This product is intended for installation into an IC or Non-IC
recessed housing.
• Suitable for damp locations.
• Supply conductors connecting to the fixture must be rated a
minimum of 90° C.
WARNINGS
FOR JUNCTION BOX (Compatible with NEW WORK box):
1. Ensure the power has been turned off by switching the circuit
breaker to the off position or by removing the fuse from the
fuse panel.
2. Remove the lens by pushing lens and turning clockwise, figure 1.
3. Select the desired color temperature by moving the selector
switch and rotating the ground wire 90 degs (if not done so already)
shown in figure 2.
5. Pre-install supplied screws into the junction box, see figure 3.
6. Cut off the orange connecter and strip wires to prepare for the next step.
6. Using supplied wire caps, connect black (hot) wires together.
White (neutral) together. Ground (green/copper) together. Ensure
the wires are safely tucked into the junction box and no wires are
being pinched or misplaced. See figure 4.
7. Align screws on junction box to the notches on the face of the disk light.
Tighten screws, ensuring the light is locked into position. See figure 5.
8. Re-attach the lens by aligning the clips to the notches, and turn
counterclockwise, as seen in figure 6.
9. Installation is now complete, restore power and the light is
now operational.
FOR RECESSED HOUSING:
1. Ensure the power has been turned off by switching the circuit breaker
to the off position or by removing the fuse from the fuse panel.
2. Remove the lens by pushing on the lens and rotating clockwise.
Attach torsion arms with supplied screws in the inner notches.
Reattach lens by aligning clips, rotate countercloskwise, seen in
figure 1 and 2.
3. Select the desired color temperature by moving the selector switch
shown in figure 3.
4. Screw E26 adapter into socket into housing, figure 4.
5. Plug the connector of the disk light into the connector of the socket
adapter assembly, figure 5.
6. Squeeze the torsion springs together and install into torsion spring
brackets inside the housing as shown in figure 6.
7. Ensure the wires are safely tucked into the junction box and no wires
are being pinched or misplaced.
8. Carefully push the LED trim until its outer edge is flush against the
ceiling surface, figure 7.
9. Installation is now complete, restore power and the light is now
operational.
INSTALLATION INSTRUCTIONS
Fig 1 Fig 2 Fig 3 Fig 4
Fig 5 Fig 6 Fig 7
Fig 1 Fig 2 Fig 3
Fig 4
Back of
disk light
inner notches
screw screw
ground
black (hot)
white (neutral)
2700K
3000K
3500K
4000K
5000K
Fig 5
2700K
3000K
3500K
4000K
5000K
Back
of light
Rotated
90 deg Ground/Green
Wire
Fig 6
/
