PackPack
2020
STAGE PAGE
96 Engine side covers 326
97 Caravan right seat 329
98 Left rear light 332
99 Rear lights 335
100 Right rear light 338
101 Rear bumbper 341
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
326
Your parts:
96A. Left engine side cover
96B. Right engine side cover
92C. Caravan right seat base
BM. 2 x 4mm screws
Stage 96: Engine side covers
327
2Secure in place with two BM screws.
1 Open the engine compartment and place the left engine side
cover (96A) inside the rear of the body.
3Install the right engine side cover inside the rear of the body. 4Fix the cover in place with two BM screws.
328
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
329
Stage 97: Caravan right seat
Your parts:
97A. Left rear light lens
97B. Left rear light housing
97C. Caravan right seat cushion
CP. 1.7 x 4mm screws
330
2Place the caravan right seat cushion (97C) on top of the
base (96C).
1 Place the left rear light housing (97B) into the lens (97A). Press
the parts together
3Secure one end of the seat cushion with a CP screw. 4Secure the other end with a second CP screw.
331
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
332
Stage 98: Left rear light
Your parts:
98A. Rear chassis beam
98B. Caravan right seat back
DP. 1.7 x 5mm screws
PP. 2 x 5mm screws
333
3Insert the posts of the caravan right seat back (98B) into the
holes in the seat base. 4Secure the back from inside the base with two DP screws.
5Place the right seat onto the side of the caravan floor, inserting
the posts into the corresponding holes. 6Secure the seat from beneath with three DP screws.
2Secure the light with a PP screw.
1 Insert the left rear light assembly from the previous stage into
the rear chassis beam (98A).
334
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
335
Your parts:
99A. Rear lights
99B. Licence plate light
99C. Tabs
99D. Cabinet
AM. 1.7 x 3mm screws
Stage 99: Rear lights
336
2Pass the cable all the way through and lay it along the inside of
the beam.
1Pass the connector end of the licence plate light (99B) through the
central hole in the rear chassis beam (98A).
3Insert the two LEDs on the rear lights cable (99A) into the holes
shown at the top of the beam, and lay the cable between the
indicated posts.
4Place four tabs (99C) over the cable in the positions shown.
337
5Secure the tabs with four AM screws.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
338
Your parts:
100A. Right rear light lens
100B. Right rear light housing
100C. Handle
100D. Hinges
100E. Large plate
100F. Medium plate
100G. Small plate
100H. Cup
HP. 1.5 x 3mm screws
PP. 1.5 x 3mm screws
Stage 100: Right rear light
339
2Mount the right rear light in the right end of the beam.
1 Place the right rear light housing (100B) into the lens (100A).
3Push the right rear LED into the right rear light housing. 4Secure the right rear light housing to the beam with a PP screw.
340
6Fix the second hinge to the cabinet with another HP screw.
5 Attach one of the hinges (100D) to the cabinet (99D) with an
HP screw.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
341
Stage 101: Rear bumper
Your parts:
101A. Rear bumper
101B. Rear bumper mounts
101C. Rear licence plate light
101D. Cabinet doors
AP 1.7 x 3mm screws
CP 1.7 x 4mm screws
GM 1.7 x 4mm screws
HP. 1.5 x 3mm screws
MS. 2.3 x 5mm screws
342
3Place the rear bumper onto the rear chassis beam (Stage 100).
Slide the license plate light over the LEDs. Align the holes at
either end of the bumper with those in the beam.
4Secure the parts together with two GM screws.
5Pass the connectors of the rear lights through the holes in left
side of the rear of the body. 6Fix the beam in place form inside the body with two SM screws.
2Place the rear license plate light (101C) in the center of the
bumper. Align the holes of both parts and secure with two AP
screws.
1Fix the rear bumper mounts (101 B) to the inside of the rear
bumper (101A) with two AP and CP screws.
343
7Insert the cabinet door handle (100C) into the center hole in the
cabinet door (101D). Secure in position with a CP screw.
Here is how your assembly should look at the end of this stage. Keep any
assemblies, unused parts and spares labelled to one side for later use.
11Secure the cabinet from below with two CP screws.
8Place the cabinet door into the front of the cabinet. Close the
hinges and align their holes with those in the door.
9 Secure the hinges to the door with four HP screws. 10Insert the two posts on the underside of the cabinet into the
corresponding holes in the caravan floor
/
