Classic Exhibits TF-5201 Setup Instructions

  • Hello! I am an AI chatbot trained to assist you with the Classic Exhibits TF-5201 Setup Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
TF-5201 10’x20’ Inline Display
Plan View
20’
10’
Perspective View
© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2017
www.classicexhibits.com
Order #XXXXX General Information
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
4
13
2
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
© 2017
www.classicexhibits.com
Order #XXXXX
Case 1 of 3
Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
Setup Hardware
Graphics
Graphics
Aero Piece Aero Piece
Aero Pieces
Aero Piece
Base Plate Base Plate
© 2017
www.classicexhibits.com
Order #XXXXX
Case 2 of 3
Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5
Halogen Lights
Graphics
Aero Piece Aero Piece Aero Piece
Aero Pieces
Wings
Base Plate Base Plate
© 2017
www.classicexhibits.com
Order #XXXXX
Case 3 of 3
Case Packing
4
2
3
Counter
ShelfShelfShelf
Shelf & Graphic
Graphic
5
Level 2
Top View of Each Level
Level 1 Level 3 Level 4
Setup Hardware
© 2017
www.classicexhibits.com
Order #XXXXX
Step 1 of 3
Backwall Assembly
When assembled
Steps:
1) Assemble aero pieces
together in numerical order.
2) Apply pillow case graphic
atop assembled aero frame.
3) Attach base plates to
aero frame using bolts.
1
2
3
4
5
6
13
14
15
16
17
18
19
20
7
8
9
10
11
12
14
13
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
© 2017
www.classicexhibits.com
Order #XXXXX
Step 2 of 3
Backwall Attachments
Wing
Wing
Wing
Wing
Wing
Wing
Steps:
1) Attach light atop assembled backwall aero frame. Refer to detail.
2) Attach wings to assembled backwall aero frame. Refer to detail.
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.
Light Connection
Attach light to
backwall where
desired and tighten
in place.
*
***
Attach standoff barrels to horizontal
and secure in place. Secure graphic
to standoffs using screw caps.
Graphic to backwall w/ Standoffs Attachment
Graphic
Threaded hole
Standoff
Barrel
Screw
Cap
Circle
Graphic
© 2017
www.classicexhibits.com
Order #XXXXX
Step 3 of 3
MOD-1331 Kiosk Assembly
When assembled
2
4
5
6
6
6
6
3
1
Item
1
2
3
4
Qty.
1
1
1
1
Description
Base Plate
48” Vertical Extrusion
25” Vertical Extrusion
38” Vertical Extrusion
Item
4a
5
5a
6
Qty.
1
1
1
4
Description
Flange Plate
38” Vertical Extrusion
Flange Plate
12” Horizontal Extrusion
Steps:
1) Attach lower verticals to base plate using bolts.
2) Attach upper vertical to lower vertical.
3) Attach shelf supports [6] to vertical [2].
4) Velcro attach shelf atop of shelf supports [6].
5) Attach flange plates atop verticals [4,5].
6) Set counter atop supports and secure in place.
Refer to detail.
7) Attach graphics to post. Refer to detail.
8) Attach monitor mount to post.
Refer to detail.
9) Attach round graphic to verticals using
screw caps. Refer to detail.
*
*
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.
**
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
Screw
4a 5a
Counter
Graphic
Graphic
Velcro on
top of shelf
supports
Graphic
Shelf
Shelf
Shelf
Counter Top Attachment Example
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
Graphic
Screw
Cap
V20
Graphic Attachment
Slide V20 connector into groove
of extrusion, then secure graphic
to connector using screw cap.
Screw
Cap
/