© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2965 - 10’x20’ Inline Display
Plan View
© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2017
www.classicexhibits.com
Order #XXXXX SEG Graphic Installation
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
© 2017
www.classicexhibits.com Case 1 of 1
Order #XXXXX Case Packing
© 2017
www.classicexhibits.com Step 1 of 7
Order #XXXXX Left Backwall Assembly
Completed Left Backwall
1
1
2
7
6
4
5
9
8
3
Item
1
2
3
4
5
6
7
8
9
Qty.
2
1
1
1
1
1
1
1
1
Description
Base Plates
39” Vertical Extrusion
39” Vertical Extrusion with Angle Cut
39” Vertical Extrusion
39” Vertical Extrusion with Angle Cut
41” Horizontal Extrusion
41” Horizontal Extrusion
45.8571” Curved Extrusion
45.8571” Curved Extrusion
Steps:
1) Attach Base Plates [1] to lower Verticals [2] and [4].
2) Connect upper Verticals [3] and [5] to lower Verticals
[2] and [4], using Connection Bars [B]. See Straight Connection
with Knobs detail.
3) Connect Horizontals [6,7] and [8,9], using Connection Bar [A].
See Straight Connection with Knobs detail.
4) Connect Vertical assemblies [2/3] and [4/5] to Horizontal
assemblies [6/7] and [8/9].
See Corner Connection with Knob detail.
Velcro facing
BACK Top Edge
Velcro facing
Back Bottom Edge
Velcro facing
BACK Inside Edge
Velcro facing
BACK Inside Edge
Connection Bar
A
B
B
*Corner Connection
with Knob
Turn Knobs Clockwise
to Tighten Lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
*
Horizontal Placement
Stopper
Set upper Horizontals
on top of Stopper,
located on Verticals.
Velcro on extrusions
must face to BACK of
assembled Backwall.
*
*
A
*
*
*
*
*
*
Front View
© 2017
www.classicexhibits.com Step 2 of 7
Order #XXXXX Right Backwall Assembly
Front View
Completed Right Backwall
Assembly
1A
1A
7A
6A
9A
8A
Item
1A
2A
3A
4A
5A
6A
7A
8A
9A
Qty.
2
1
1
1
1
1
1
1
1
Description
Base Plates
39” Vertical Extrusion
39” Vertical Extrusion with Angle Cut
39” Vertical Extrusion
39” Vertical Extrusion with Angle Cut
41” Horizontal Extrusion
41” Horizontal Extrusion
45.8571” Curved Extrusion
45.8571” Curved Extrusion
Velcro facing
BACK Top Edge
Velcro facing
Back Bottom Edge
Velcro facing
BACK Inside Edge
Velcro facing
BACK Inside Edge
Connection Bar
A
B
B
*Corner Connection
with Knob
Turn Knobs Clockwise
to Tighten Lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
*
Horizontal Placement
Stopper
Set upper Horizontals
on top of Stopper,
located on Verticals.
Velcro on extrusions
must face to BACK of
assembled Backwall.
*
*
A
*
*
*
*
*
*
2A
4A
5A
3A
Steps:
1) Attach Base Plates [1A] to lower Verticals [2A] and [4A].
2) Connect upper Verticals [3A] and [5A] to lower Verticals
[2A] and [4A], using Connection Bars [B]. See Straight Connection
with Knobs detail.
3) Connect Horizontals [6A,7A] and [8A,9A], using Connection Bar [A].
See Straight Connection with Knobs detail.
4) Connect Vertical assemblies [2A/3A] and [4A/5A] to Horizontal
assemblies [6A/7A] and [8A/9A].
See Corner Connection with Knob detail.
© 2017
www.classicexhibits.com Step 3 of 7
Order #XXXXX Left to Right Backwall & Attachments
4
5
2
3
8A
Screw
Cap
Left Backwall
Right Backwall
Steps:
1) Attach Panels to Verticals [2/3] and [4A/5A], using screw caps.
2) Attach Wing panels to A10 clamps. See Wing Attachment detail.
3) Attach Light to top of Backwall. See Light Connection detail.
4) Attach Headers to Extrusions [3A] & [8A]. See Header Attachment detail.
5) Attach Graphics to Velcro on back of Backwall. See SEG
Graphic Installation page for instruction.
3A
2A
Slide A10 clamp into
groove of Extrusion.
When desired location
is found, tighten
Set Screw to secure.
Set
Screw
A10
Tighten Black Plastic
Set Screw to secure
Wing in place.
Wing Attachment
Keep A10 clamps
attached to Verticals
Black
Plastic
Set Screw
Light Connection
Connect Lights to
Horizontal where
desired and
tighten in place.
*
*
*
*
Connector
Header Attachment
Cap
Header
Standoff
Slide Connector into groove of Vertical Extrusion. Tighten
set screws to secure in place. Screw Standoff into
Connector. Place Header between Standoff and Cap,
then screw Cap to tighten in place.
*
*Header
Header
4A
5A
© 2017
www.classicexhibits.com Step 4 of 7
Order #XXXXX Light Frame Attachment
Plan View
Screw Cap
Light Frame
Blocker Fabric
SEG Graphic
Standoff Barrel
5
9
Screw Cap
Steps:
1) Attach Light Frame to Extrusions [5/9]. See Light Frame Attachment detail.
2) Apply SEG Graphic to font of Light Frame and Blocker fabric to back.
See SEG Graphic Installation page for instruction.
3) Connect lighting power cords, route power cord thru hole in Blocker, then attach
to transformer. See Light to Light Connections & Light to Transformer details.
Attach Standoff Barrels to Backwall, using Connectors.
Connect Light Box to Standoff Barrels, using Screw Caps.
Tighten Screw Caps to secure.
Light Frame Attachment
Light Frame
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
Light to Light Connection
Light to Tranformer Connection
*
*
Standoff
Barrel
Slide Connector on back
of Standoff Barrel into
groove of extrusion.
Tighten to secure.
Standoff Attachment
*Connector
© 2017
www.classicexhibits.com Step 5 of 7
Order #XXXXX Left Backwall Attachments
10
11
11A
12
Completed Left Assembly
Item
10
11
11A
12
Qty.
1
1
1
1
Description
11.5” Horizontal Extrusion
26.75” Curved Extrusion
Flange Plate
20.3” Curved Extrusion
*
**
*
Screw
Scale: 40
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of Connector to
Literature Holder. Attach flat end of
Connector to vertical extrusion.
Tighten locks to secure.
*
Monitor Mount
Connectors
*
Slide Connectors into groove
of Extrusion. Tighten Set Screws
to secure Connectors in place.
Attach Monitor Mount back
plate to Extrusion, using Bolts.
Bolts
Monitor
Mount
*
Shelf
Shelf Attachment
Insert Lock into groove of Vertical
Extrusion, then tighten Set Screw.
Lock
Set Screw
Back of Shelf
*
*
10
11
11A
12
Screw
*
Shelf
*
Counter Top Attachment
*
Wing Nut
Fixed
Screws
Flange
Plate [11A]
11
10
Counter Top
Attach Flange Plate [11A] to Curved Extrusion
[11], using screw. Insert Fixed Screws, located
on underside of Counter, into holes of Flange
Plate. Secure with Wing Nuts.
Steps:
1) Attach assembled Extrusions [10/11] to Verticals [2] & [4].
2) Attach Curved Extrusion [12] to Curved Extursion [11].
3) Connect Flange Plate [11A] to top of Curved Extrusion [11],
using screw.
4) Attach Counter Top to Flange Plate [11A].
See Counter Top Attachment detail.
5) Attach Shelves to Curved Extrusion [11].
See Shelf Attachment detail.
6) Attach Monitor Mounts to Vertical Extrusions [3] & [5].
See Monitor Mount detail.
7) Attach Literature Holders to Vertical Extrusions [3] & [5].
See Literature Holder Attachment detail.
Note: Horizontal Extrusion [10] and Curved
Extrusion [11] stay assembled for
shipping and packing.
4
5
2
3
© 2017
www.classicexhibits.com Step 6 of 7
Order #XXXXX Right Backwall Attachments
10
11
11A
12
Completed Right Assembly
Item
10
11
11A
12
Qty.
1
1
1
1
Description
11.5” Horizontal Extrusion
26.75” Curved Extrusion
Flange Plate
20.3” Curved Extrusion
Steps:
1) Attach assembled Extrusions [10/11] to Verticals [2A] & [4A].
2) Attach Curved Extrusion [12] to Curved Extursion [11].
3) Connect Flange Plate [11A] to top of Curved Extrusion [11],
using screw.
4) Attach Counter Top to Flange Plate [11A].
See Counter Top Attachment detail.
5) Attach Shelves to Curved Extrusion [11].
See Shelf Attachment detail.
6) Attach Monitor Mounts to Vertical Extrusions [3A] & [5A].
See Monitor Mount detail.
7) Attach Literature Holders to Vertical Extrusions [3A] & [5A].
See Literature Holder Attachment detail.
*
**
*
Screw
Note: Horizontal Extrusion [10] and Curved
Extrusion [11] stay assembled for
shipping and packing.
Scale: 40
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of Connector to
Literature Holder. Attach flat end of
Connector to vertical extrusion.
Tighten locks to secure.
*
Monitor Mount
Connectors
*
Slide Connectors into groove
of Extrusion. Tighten Set Screws
to secure Connectors in place.
Attach Monitor Mount back
plate to Extrusion, using Bolts.
Bolts
Monitor
Mount
*
Shelf
Shelf Attachment
Insert Lock into groove of Vertical
Extrusion, then tighten Set Screw.
Lock
Set Screw
Back of Shelf
*
*
10
11
11A
12
4A
5A
2A
3A
Screw
*
Shelf
*
Counter Top Attachment
*
Wing Nut
Fixed
Screws
Flange
Plate [11A]
11
10
Counter Top
Attach Flange Plate [11A] to Curved Extrusion
[11], using screw. Insert Fixed Screws, located
on underside of Counter, into holes of Flange
Plate. Secure with Wing Nuts.
© 2017
www.classicexhibits.com Step 7 of 7
Order #XXXXX
Qty. 2
Counter
Infill
Infill
Infill
Hinge
6
3
2
4
4
2
1
1
3
10
9
12
11
5
1
8
7
Completed Pedestal
Assembly
Item
1/2
3/4
5
6/7
8
9
10/11
12
Qty.
1/1
1/1
1
1/1
1
1
1/1
1
Description
38” Vertical Extrusion w/ cut
38” Vertical Extrusion
18.9” Horizontal Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
22.5” Curved Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
Steps:
1) Attach lower Horizontals [5,6,7,8] between Verticals [1,2,3,4].
2) Connect Door to Vertical [4]. See Door Connection detail.
3) Insert Infills between Verticals [1/2, 1/3, and 2/4].
4) Attach upper Horizontals [9,10,11,12] between Verticals [1,2,3,4].
5) Connect Shelf Supports to Velcro on Infills, then place Shelf on top.
6) Place Counter on top. See Counter Top Attachment detail.
7) Attach Literature Holder to Vertical [1].
See Literature Holder Attachment detail.
Hinge
Door
*
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of Connector to
Literature Holder. Attach flat end of
Connector to Vertical Extrusion.
Tighten locks to secure.
*
Door
Hinge
Hinge
Pin
Slide Pin into
Hinge attached
to Vertical.
Slide Door
Hinge over Pin.
Door Connection
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
Shelf
(4) Shelf
Supports
*
*
MOD-1297 Modied Pedestal Assembly
/
