© 2016
www.classicexhibits.com
Order #XXXXX -
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-1110 General Layout
Plan View
Perspective View
10’
10’
© 2016
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2016
www.classicexhibits.com
Order #XXXXX -
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information
© 2016
www.classicexhibits.com
Order #XXXXX -
Crate 1 of 1
Crate Packing - 1 of 1
© 2016
www.classicexhibits.com
Order #XXXXX -
Step 1 of 3
Backwall Assembly
Item
1
1A
2
3
4
5
6/6A
7/7A
8
9
Qty.
2
2
1
1
1
1
2/2
1/1
2
4
Description
Base Plate
Base plate w/ two holes
95.75”h Q914 Vertical Extrusion
95.75”h Q914 Vertical Extrusion
95.75”h Q914 Vertical Extrusion
95.75”h Q914 Vertical Extrusion
30”w Z45 Horizontal Extrusion
36”w Z45 Horizontal Extrusion
37.75”h Q914 Vertical extrusion
9”w Z45 Horizontal Extrusion
1
1A
1A
1
6
7
6
9
8
9
9
8
9
2
5
3
4
7A
6A
6A
Steps:
1) Connect base plates [1] to verticals [2] & [5];
repeat step to connect base plates [1A] to verticals [3] & [4].
2) Connect horizontals [6], [6A] [7] & [7A] between verticals [2, 3, 4 & 5] where indicated.
3) Attach verticals [8] to base plates [1A],and connect
horizontals [9] between vertical [3] & [8] and [4] & [8] where indicated.
4) Attach Graphics to the frame using velcro on the back side of the frame.
Velcro
PR37
Extrusion
Profile
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge
Attach graphic
to velcro on back of
assembled frame
© 2016
www.classicexhibits.com
Order #XXXXX -
Step 2 of 3
Backwall Assembly Cont’d
When assembled
Steps:
1) Place counters on top of verticals [7] and secure in place.
See Counter Top Attachment detail.
2) Attach monitor mounts to backwall where indicated.
See Monitor Mount Attachment detail.
3) Attach lights on top of assembled backwall.
See Light Connection detail.
Counter
Counter
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
***
*
*
*
**
Counter Top Attachment
*
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
Monitor Mount Attachment
1) Attach back plate to monitor.
2) Attach bolts to vertical.
3) Hang mounting plate from bolts.
4) Connect back plate to mounting
plate; use bolts, washers, and a nut.
*
© 2016
www.classicexhibits.com
Order #XXXXX -
Step 3 of 3
MOD-1289 - Pedestal Assembly
When Assembled
1
2
35
7
1
2
Infill
Infill
Infill
9
4
6
8
Door
Shelf
(4) Shelf
Supports
Counter Top
Counter
Item
1
2
3
4
5
6
7
8
9
Qty.
1
1
1
1
1
1
1
1
1
Description
38” S44 Vertical Extrusion
38” S44 Vertical Extrusion
41.2385” Z45 Curved Horizontal Extrusion
41.2385” Z45 Curved Horizontal Extrusion
16.35” Z45 Horizontal Extrusion
34.41” Z45 Vertical Extrusion w/ Door Hinges
41.2385” Z45 Curved Horizontal Extrusion
41.2385” Z45 Curved Horizontal Extrusion
16.35” Z45 Horizontal Extrusion
Item Description
1 5.75”r x 42“h Half Curve Panel
2 5.75”r x 42“h Half Curve Panel
Steps:
1) Attach curved panels [1,2] together.
2)
Attach lower horizontals [3,4,5] between
assembled curved panels and verticals [1,2].
3) Attach vertical [6] to lower horizontal [4], Placing
infill as shown.
4) Insert infills as shown.
5) Attach upper horizontals [7,8,9] between
assembled curve panels and verticals [1,2] atop infills.
6) Hang door from hinges as shown in detail.
7) Place internal shelf on shelf supports
8) Set counter tops on top of assembled base.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
/
