© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2923 10’x20’ Inline Display
Perspective View
Plan View 20’
10’
© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2017
www.classicexhibits.com
Order #XXXXX General Information
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
4
13
2
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
© 2017
www.classicexhibits.com
Order #XXXXX
Crate 1 of 1
Crate Packing
© 2017
www.classicexhibits.com
Order #XXXXX
Step 1 of 9
Vertical Assembly 1
Assembling
Right
Left
Center
Center
Left
Right
26 27
43
46
43
46
33 33
39 39
Infill Infill
Infill InfillInfill
Infill Infill
28 2930
34
34
34
34
31
When assembled
Item
26
27
28
29
30
31
33
34
39
43
46
Qty.
1
1
1
1
1
1
2
4
2
2
2
Description
96”h Vertical Extrusion
96”h Vertical Extrusion
96”h Vertical Extrusion
96”h Vertical Extrusion
96”h Vertical Extrusion
96”h Vertical Extrusion
16”w Horizontal Extrusion
16”w Horizontal Extrusion
16”w Horizontal Extrusion
16”w Horizontal Extrusion
16”w Horizontal Extrusion
Steps:
1) Connect horizontal extrusions between verticals
Placeing Infills between each vertical
where indicated.
*
* * * *
* *
* *
* *
Wire Management Attachment
Steps:
1) Run cords through plastic conduit.
2) Attach conduit where indicated by
pinching the opening and inserting
into the groove.
pinch
PR63 for wire management
© 2017
www.classicexhibits.com
Order #XXXXX
Step 2 of 9
Connection Assembly
Plan View
Hinge
35
36
36
32
35
36
36
32
Door Stoper
Door Stoper
Door Stoper
Door Stoper
Door Stoper
Door Stoper
Door Stoper
Door Stoper
Item
32
35
36
Qty.
2
2
4
Description
79”h Vertical Extrusion
Curved Extrusion
Curved Extrusion
Steps:
1) Connect lower curved extrusions [36]
between vertical assemblies and
vertical extrusions [32].
2) Connect lower curved extrusions [35]
between assemblies.
3) Connect Wire management verticals.
Refer to Wire Management
Attachment detail.
NOTE: Keep PR37 attached to [32] for packing.
If removed, refer to detail to re-attach.
*
*
*
*
*
Wire Management Attachment
Steps:
1) Run cords through plastic conduit.
2) Attach conduit where indicated by
pinching the opening and inserting
into the groove.
pinch
PR63 for wire management
Slide PR37 extrusion into
groove of vertical and tighten
set screw to secure in place.
DOOR STOPPER
PR37
Extrusion
Profile
Hinge
HingeHinge
Hinge
Hinge
Hinge Hinge
© 2017
www.classicexhibits.com
Order #XXXXX
Step 3 of 9
Side 1 Assembly
40
42
Ceiling
lights
Clear Infill
41
Clear Door
Shelf
Shelf
Shelf
Clear Door
40
40
When assembled front view
38
38
37
White Door White Door
Shelf
Infill
Item
37
38
40
41
42
Qty.
forstep
1
2
3
1
1
Description
Curved Extrusion
Curved Extrusion
15.5”w Horizontal Extrusion
Curved Extrusion
Curved Extrusion
Steps:
1) Attach small white doors to front verticals on top of lower hinges.
Refer to Door Attachment detail.
2) Insert infill graphic to between backside assembled verticals.
3) Connect curved extrusion [37] atop backinfill.
4) Connect front curved extrusions between verticals atop doors.
5) Place Shelf on top of curved extrusions [37] & [38].
6) Connect Horizontal [40] to vertical [32].
7) Insert clear infill between back verticals.
8) Attach doors as shown in Door Attachment detail.
9) Connect backside curved extrusion [42] between back verticals.
10) Connect front side curved extrusion [41] between front verticals.
11) Place ceiling on top of curved extrusions [41] & [42]
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
HingeHinge
HingeHinge
© 2017
www.classicexhibits.com
Order #XXXXX
Step 4 of 9
Side 1 & 2 Assembly
44
45
White Door White Door
38
38
37
When assembled
Item
37
38
44
45
Qty.
for step
1
2
1
1
Description
Curved Extrusion
Curved Extrusion
Curved Extrusion
Curved Extrusion
Steps:
1) Insert Infills between front and back verticals.
2) Connect curved extrusions [44] & [45] between verticals.
3) Place ceiling on top of curved extrusions [44] & [45].
4) Attach doors to hinges as shown in detail.
5) Connect curved extrusions [37] & [38] between
vertical assemblies.
6) Place shelf on top of curved extrusion extrusions.
Ceiling
Shelf
Infill
Infill
Infill
Lights
HingeHinge
HingeHinge
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
© 2017
www.classicexhibits.com
Order #XXXXX
Step 5 of 9
Side 2 Assembly
Item
41
42
44
45
Qty.
1
1
1
1
Description
Front Curved Extrusion
Curved Extrusion
Front Curved Extrusion
Curved Extrusion
Steps:
1) Attach front doors as shown in detial.
2) Insert large back infill between center and side
assembled verticals.
3) Connect front and back curved extrusions [41] & [42].
4) Place ceiling with lights on top of [41] & [42].
5) Insert small white graphic infills between center and
side assembled verticals.
6) Connect front and back curved extrusions [44] & [45]
between center and side vertical assemblies.
7) Place Ceiling atop top curved extrusions.
Hinge
Hinge
HingeHinge
41
45
44
42
White Door White Door
Ceiling
Infill
Graphic
Graphic
Ceiling
Lights
© 2017
www.classicexhibits.com
Order #XXXXX
Step 6 of 9
Vertical Assembly 2
When assembled
Clear Infill
Graphic Infill
Graphic Infill
Graphic Infill
Hinge
1 2
3
4
5
6
8 7
9
10
11
12
13 14
15
15
15
15
Hinge Hinge Hinge
Hinge Hinge Hinge Hinge
Graphic Infill
White InfillWhite Infill
Item
1
2
3-6
7
8
9-12
Qty.
1
1
1 ea.
1
1
1 ea.
Description
96”h Vertical Extrusion
96”h Vertical Exturison
16”w Horizontal Extrusion
96”h Vertical Extrusion
96”h Vertical Extrusion
16”w Horizontal Extrusion
Steps:
1) Connect horizontal extrusions between verticals
Placeing Infills between each vertical
where indicated.
2) Attach verticals Wire Management Attachment
where indicated.
Left Assembly Center Assembly Right Assembly
HingeHingeHingeHinge
*
**
**
*
***
**
Wire Management Attachment
Steps:
1) Run cords through plastic conduit.
2) Attach conduit where indicated by
pinching the opening and inserting
into the groove.
pinch
PR63 for wire management
© 2017
www.classicexhibits.com
Order #XXXXX
Step 7 of 9
Mid & Top Section Assembly
Front and back when assembled
20
17
17
17
17
Graphic Graphic
Shelf
Shelf
Shelf
Shelf
Shelf
Lights
18 21
22
22
22
18
21
18
16
Door Stopper
Door Stopper
Door Stopper
Door Stopper
16
18
20
Item
16
17
18
19
20
21
22
23
24
25
Qty.
2
4
4
2
2
2
3
2
2
2
Description
79”h Vertical Extrusion
Curved Extrusion
Curved Extrusion
Curved Extrusion
Curved Extrusion
Curved Extrusion
15.5”w Horizontal Extrusion
Curved Extrusion
Curved Extrusion
Curved Extrusion
Steps:
1) Connect curved extrusions [17 & 18] between vertical
assemblies and vertical [16].
2) Connect curved extrusions [20 & 21] (w/ graphic infill between)
to vertical assemblies.
3) Place Shelf with lights on top of left side curved extrusions [18 & 21]
and shelf w/out lights on the right.
4) Connect horizontals [22] to vertical [16].
5) Place Shelves atop horizontal extrusions [22].
6) Insert Large infills between assembled verticals (Clear Infill on the right).
7) Connect curved extrusions [19 & 23] between assembled verticals.
8) Place lower ceiling and graphic infills on top of curved extrusions [19 & 23].
9) Connect curved extrusions [24 & 25] between vertical assemblies.
10) Place ceiling infills on top of curved extrusions [24 & 25].
Graphic Clear Infill
Graphic
Ceiling
Ceiling
Lights Lights
Ceiling
Ceiling
Graphic
Graphic
Graphic
23
23
19 19
25
25 24 24
© 2017
www.classicexhibits.com
Order #XXXXX
Step 8 of 9
Door Assembly
When assembled
Steps:
1) Attach lower and upper doors to verticals as shown.
Refer to Door Attachment detail
Hinge
Hinge
HingeHingeHingeHinge
Hinge
Hinge Hinge Hinge
Hinge
Hinge Hinge
HingeHinge
Hinge Hinge
HingeHingeHingeHinge
HingeHingeHinge
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
© 2017
www.classicexhibits.com
Order #XXXXX
Step 9 of 9
LTK-1136 Reception Counter
When assembled
Item
1
2
3
4
5
6
7
8
9
10
11
12
Qty.
1
1
1
1
1
1
1
1
1
1
3
1
Description
23”w x 38”h Flat Panel
23”w x 38”h Flat Panel
38”h Quarter Curved Panel
38”h Quarter Curved Panel
23”w x 38”h Flat Panel w/ Door
23”w x 38”h Flat Panel w/ Door
38”h Quarter Curved Panel
38”h Quarter Curved Panel
Round Base Plate
37.75”h Round Vertical Extrusion
38.1728” Curved Horizontal Extrusion
Flange Plate
First install Lower Extrusion
then Lower Plex Shelf.
Repeat for installing Middle
Extrusion and Middle Plex Shelf
1
2
3
7
6
5
4
8
10
Middle
Clear Plex Shelf
Clear Plex Counter
Primary Counter
Lower
Clear Plex
Shelf
11
11
11
12
9
Steps:
1) Connect panels together in numerical order as shown in illustrations.
2) Attach base plate [9] to vertical [10].
3) Attach lower curved support [11] between vertical and
assembled base; place lower plex shelf on horizontal [11].
4) Repeat step [3]; attach upper horizontal [11].
5) Attach flange plate [12] on top of vertical [10] as shown.
6) Attach shelf supports to inside of assembled pedestal; place internal shelf on supports.
7) Set counter top on top of assembled pedestal.
Refer to
Counter Top Attachment
detail.
8) Attach plex top with stand-offs and caps as shown.
Refer to
Plex Shelf to Counter Attachment
detail.
Lock
Setscrew
S10
Counter Top
Attachment
Insert screws located
on underside of counter
into holes on flange plate
and secure with wing nuts.
Wing Nut
*
Plex Counter Attachment
*
Attach stand-off
barrels to primary
counter top.
Connect plex
counter to primary
counter top using
screw caps.
**DO NOT
OVER TIGHTEN.
PLEX WILL CRACK**
Screw Cap
Plex Counter
*
*
***
*
*
/
