© 2021
Order #XXXXX
Locked layer contains
placeholder marks.
10’
10’
Plan View
TF-506 - 10’x10’ Hybrid Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2021
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2021
Case 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Graphic Wings
Round Sign
Baseplates
Graphics
Lights
Setup Hardware
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4 Level 5
Case Packing
© 2021
Case 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Counter
Shelf & Graphic
Graphic
2
3
ShelfShelfShelf
4 5
Setup Hardware
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4
Case Packing
© 2021
Step 1 of 3
Order #XXXXX
Using Your Setup Instructions
The Aero Setup Instructions are created specifically for your configuration. The instructions include an
exploded view of the frame which is sequentially labeled. We encourage you to review the instructions
before attempting to assemble your exhibit.
Connections are kept very simple; no tools required. Everything assembles with push-button connectors.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Push-Button
Push-Button
66
6
6
Numbered Label
Connections are made by holding the button down and
sliding the red tube into opposing tube until button locks
into the hole of the opposing tube. To disassemble, push button
and pull or twist extrusions apart.
Locked layer contains
placeholder marks.
When
assembled
A1
A2
A3
A4
A5
A6
Steps:
1) Assemble aero pieces
together in numerical order.
2) Apply pillow case graphic
to assembled aero frame.
3) Attach base plates to
aero frame using bolts.
4) Connect light to frame
where desired.
Aero Frame Attachments
© 2021
Step 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Graphic
When Assembled
Wing
Wing
Wing
Wing
Wing
Wing
Steps:
1) Attach light atop assembled backwall aero frame (see
Light Connection
detail)
2) Attach wings to assembled backwall aero frame (see
A10 Clamp Detail
)
3) Attach round graphic to assembled backwall aero frame (see
Graphic Attachment
detail)
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.
*
*
Graphic
Screw
Cap
Stand-Off
Barrel
Screw stand-off barrels into
threaded Hole. Attach graphic
to stand-offs using screw caps.
Graphic Attachment
Threaded
Hole
*
*
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
*
Attachments
© 2021
Step 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
2
4
5
6
6
6
6
3
1
Item
1
2
3
4
Qty.
1
1
1
1
Description
Base Plate
48” Vertical Extrusion
25” Vertical Extrusion
38” Vertical Extrusion
Item
4a
5
5a
6
Qty.
1
1
1
4
Description
Flange Plate
38” Vertical Extrusion
Flange Plate
12” Horizontal Extrusion
Steps:
1) Attach lower verticals to base plate using bolts.
2) Attach upper vertical to lower vertical.
3) Attach shelf supports [6] to vertical [2].
4) Velcro attach shelf atop of shelf supports [6].
5) Attach flange plates atop verticals [4,5].
6) Set counter atop supports and secure in place.
Refer to detail.
7) Attach graphics to post. Refer to detail.
8) Attach monitor mount to post.
Refer to detail.
9) Attach round graphic to verticals using
screw caps. Refer to detail.
*
*
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.
**
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
Screw
4a 5a
Counter
Graphic
Graphic
Velcro on
top of shelf
supports
Graphic
Shelf
Shelf
Shelf
Counter Top Attachment Example
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
Graphic
Screw
Cap
V20
Graphic Attachment
Slide V20 connector into groove
of extrusion, then secure graphic
to connector using screw cap.
Screw
Cap
MOD-1331 Pedestal Assembly
/
