Classic Exhibits TF-512 Setup Instructions

Brand: Classic Exhibits

Model: TF-512

Type: Setup Instructions

www.classicexhibits.com

Order #XXXXX TF-512 General Layout

Plan View 10’

10’

SETUP INSTRUCTIONS

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

www.classicexhibits.com

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all setscrews

and locks during disassembly

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

www.classicexhibits.com Case 1 of 2

Order #XXXXX Case 1 Packing

www.classicexhibits.com Case 2 of 2

Order #XXXXX Case 2 Packing

Shelf Supports

Shelf 5, 5A

5, 5A

4 3 2 1

Counter

Infills

6,7 6A,7A

Lit. Racks

Setup Hardware

Top View of Each Level

Level 1 Level 2 Level 3 Level 4 Level 5

www.classicexhibits.com

Order #XXXXX

When assembled

Item

1/1A

2/2A

3/3A

4/4A

Qty.

1/1

Description

Base Plate

47.5”h Vertical Extrusion

26”w Horizontal Extrusion

37”h Vertical Extrusion

12”w Horizontal Extrusion

Steps:

1) Attach base plates [1] & [1A] to lower verticals [2] & [3].

2) Attach upper verticals [2A] & [3A] to lower verticals [2] & [3].

3) Connect lower and upper horizontals [4] & [4A] between verticals.

4) Attach Graphics to the back side of the backwall.

5) Connect horizontals [6] & [7] between verticals [5] and backwall.

6) Attach horizontal [8] to front of upper verticals [2A] & [3A].

BACK SIDE

Velcro: Top

Edge

Velcro: Bottom

Edge

Velcro: Inside

Edge

Velcro: Inside

Edge

Velcro

PR37

Extrusion

Profile

Screws

Connector

Piece

S44 Connector

Silde extrusion over

connector and rest on

lower vertical;

secure with screws.

**To prevent product loss,

Keep all screws attached

to connector piece after

disassembling

Monitor Mount Plate Attachment

Attach mounting plate

to verticals as shown.

1) Screw Aero Mount

to base plate.

2) Slide Aero Frame

over mount.

Canopy Attachment

to Base Plate

Backwall Assembly

www.classicexhibits.com Step 1 of 3

Order #XXXXX Backwall Attachments

Header

Counter

Shelf

When assembled

Steps:

1) Place shelves on lower horizontals.

2) Connect counter to front verticals and upper horiozntals.

3) Attach monitor mount to monitor mount plate as shown.

4) Attach header to upper verticals where indicated.

Velcro

Monitor Mount Attachment

Then attach

wall plate to plate

using bolts and wing nuts

Attach standoff barrels to counter

and secure in place. Secure upper

shelf to standoffs using screw caps.

Upper Shelf to Counter Attachment

Upper Shelf -

Clear Plex

Threaded hole

in counter top

Standoff

Barrel

Screw

Cap

www.classicexhibits.com Step 2 of 3

Order #XXXXX

Item

Qty.

Description

Base Plate

Steps:

1) Assemble aero frame in numerical order as shown.

2) Attach Graphic to aero frame.

3) Attach aero frame to base plate as shown in detail.

Note: aero key slide used for vertical aero.

4) Attach Light to top of aero frame.

Aero Frame

Canopy

Mount

Base Plate

Bolt

1) Screw Aero Mount to base plate.

2) Slide Aero Frame over mount.

Canopy Attachment

to Base Plate

Aero Key Slide

Slide top and bottom

key into the

groove of the

vertical extrusion.

Light Connection

Attach lights to

backwall where

desired and

tighten in place.

678

Aero Frame Assembly

Connections are made by holding the button

down and sliding the red tube into opposing

tube until the connection is made. To disassemble

push button and pull or twist extrusions apart.

Push-Button

Numbered Label

Using Your Setup Instructions

The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an

exploded view of the frame which is sequentially numbered. We encourage you to study the instructions

before attempting to assemble your exhibit.

Connections are kept very simple: no tools. Everything assembles with push-button

connectors and pre-connected horizontal sections.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

www.classicexhibits.com Step 3 of 3

Order #XXXXX Pedestal Assembly

Infill

Door

Shelf Supports

Shelf

Counter

5A 6A

HingeHinge

When assembled

Item

5/5A

6/6A

7/7A

Qty.

2/2

1/1

Description

37.5”h Vertical Extrusion

13.25”w Horizontal Extrusion

22.5”w Horizontal Extrusion

Steps:

1) Connect lower horizotnals [5], [6] & [7] between verticals [1-4].

2) Place infill between infills between verticals [1-4].

3) Attach door using Door Attachment detail.

4) Place shelf on shelf supports.

5) Attach upper horizontals [5A], [6A] & [7A] between verticals [1-4].

6) Attach iPad clam shell to counter using bolt under counter.

7) Place counter and iPad clam shell to lower assembly as shown.

BACK SIDE

FRONT SIDE

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Attachment

Hex

Nuts

Clam Shell rotates

between portrait

and landscape

viewing modes.

Swivel

Mounting

Plate

Swivel iPad Clamshell

Attachment

Bolt iPad clamshell to mounting

plate with hex nuts.

Wire

Access

iPad

Lock

Classic Exhibits TF-512 Setup Instructions

Brand: Classic Exhibits

Model: TF-512

Type: Setup Instructions

Download PDF

report

in other languages

polski: Classic Exhibits TF-512

Classic Exhibits TF-512 Setup Instructions

Classic Exhibits TF-512 Setup Instructions

in other languages

Related papers

Other documents