RIM CYLINDER
1-1/8" TO 1-3/8" LONG
IC OR STANDARD
CORE
7/16" TALL CYLINDER COLLAR WITH WAVE SPRING
WASHER FOR 1-1/4 TO 1-3/8" LONG CYLINDERS
(PURCHASED SEPARATELY)
CYLINDER COLLAR - PROVIDED WITH CYLINDER
FOR 1-1/8" LONG CYLINDERS ONLY
CYLINDER CUP
BREAK-OFF
SCREWS
TAB MUST FIT INTO
SLOT ON PULL PLATE
BREAK-OFF SCREWS
PROVIDED WITH
RIM CYLINDER
2 3/4"
70
2 7/8"
73
DOOR
1/4"-20 PAN HEAD
MACHINE SCREWS (2X)
1/4"-20 THRU BOLTS
(2X)
RAISED LIP PULL
ASSEMBLY
7/16" MOUNTING HOLES (2X)
STANDARD 2-1/8" HOLE
FOR BORED LOCKS
4700 EXIT DEVICE
HEAD CHASSIS
STEP 1: INSTALL CYLINDER (SKIP TO STEP "2" FOR DUMMY PULL - 47RD)
INSTALL RIM CYLINDER THROUGH WAVE WASHER AND COLLAR.
A.
THE THINNER COLLAR PROVIDED WITH THE RIM CYLINDER CAN BE
USED FOR 1-1/8" LONG CYLINDERS ONLY.
INSERT RIM CYLINDER THROUGH HOLE IN RAISED LIP PULL AND INSTALL
B.
CYLINDER CUP FROM THE BACKSIDE OF THE RAISED LIP PULL PLATE.
SECURE RIM CYLINDER ASSEMBLY USING THE 2 BREAK-OFF SCREWS
C.
PROVIDED WITH THE RIM CYLINDER.
TRANSFER HORIZONTAL CENTERLINE FROM EXIT DEVICE SIDE OF THE DOOR.
A.
THIS SHOULD COINCIDE WITH THE CENTER OF THE EXISTING BORED LOCK CUTOUT.
TRANSFER BACKSET CENTERLINE FROM EXIT DEVICE SIDE OF THE DOOR.
B.
THIS SHOULD COINCIDE WITH THE CENTER OF THE EXISTING BORED LOCK CUTOUT.
FOR 4700 RIM EXIT DEVICE AND A STANDARD 5/8" FRAME STOP, THE BACKSET
A.
SHOULD BE 2-3/4" FOR PROPER STRIKE ENGAGEMENT.
SEE EXIT DEVICE INSTRUCTIONS FOR OTHER APPLICATIONS.
B.
USE TEMPLATE OR DIMENSIONS FROM PAGE 2 TO MARK MOUNTING HOLE LOCATIONS.
C.
DRILL TWO
7/16" CLEARANCE HOLES FOR MOUNTING POSTS. BE SURE THESE
D.
HOLES ARE VERTICALLY CENTERED ON THE EXISTING 2-1/8" BORED LOCK HOLE.
INSTALL RAISED LIP PULL WITH THROUGH BOLTS THROUGH DOOR.
E.
RIM CYLINDER TAILPIECE SHOULD INSERT INTO THE EXIT DEVICE CAM
A.
APPROXIMATELY 7/16"
1/16". IF IT'S TOO LONG, CAREFULLY MEASURE AND
MARK AT THE CLOSEST BREAK-OFF LINE.
THEN USE PLYERS TO BREAK-OFF EXCESS, CAREFUL NOT TO BREAK-OFF
B.
TOO MUCH.
SECURE RAISED LIP PULL PLATE AND EXIT DEVICE USING THE 2 MOUNTING SCREWS.
F.
STEP 2: INSTALL RAISED LIP PULL PLATE
SHEET 1 OF 2
47RN & 47RD RAISED LIP PULL INSTRUCTIONS
FOR RETROFITTING DOORS PREPPED FOR BORED LOCKS (ANSI A115.2)
FOR USE WITH 4700 SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
DRAWING NO: I-ED00337
REV: 02
1.16
29
.45
(SEE NOTE 2)
11
.12
3
.24
6
1.24
31
EXIT DEVICE
C
L
(SEE NOTE 1)
RIM CYLINDER
C
L
7.74
197
3.00
76
R
.39
10
3.87
98
3.87
98
7.74
197
1.50
38
1.50
38
1.44
37
1.44
37
.24
6
2.13
EXISTING
2-1/8"
BORED LOCK HOLE
54
REQUIRES A
0.44"[11]
CLEARANCE HOLE
THROUGH DOOR (2X)
C
L
CORRESPONDS
TO EXIT DEVICE
C
L
NOTES:
MATCH THIS CENTERLINE UP WITH THE EXIT DEVICE CENTERLINE.
1.
THIS WILL ENSURE THE RIM CYLINDER TAILPIECE LINES UP WITH THE
EXIT DEVICE TAILPIECE CAM.
DIMENSION SHOWN IS FOR HAGER CYLINDER COLLAR ONLY.
2.
C
L
CORRESPONDS
TO EXIT DEVICE
C
L
PRIMARY DIMENSIONS SHOWN IN INCHES,
DIMENSIONS IN [ ] ARE MILLIMETERS.
47RN & 47RD RAISED LIP PULL INSTRUCTIONS
FOR RETROFITTING DOORS PREPPED FOR BORED LOCKS (ANSI A115.2)
FOR USE WITH 4700 SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
REV: 02
DRAWING NO: I-ED00337
SHEET 2 OF 2
/
