Hagerco 47PT Operating instructions

Hagerco
Brand
Hagerco
Model
47PT
Type
Operating instructions

This manual is also suitable for

STEP 1: INSTALL CYLINDER (47PT ONLY)
STEP 2: INSTALL PULL PLATE
A. INSTALL MORTISE CYLINDER THROUGH WAVE WASHER, CYLINDER SPACER
RING (IF NEEDED) AND COLLAR.
B. INSERT MORTISE CYLINDER THROUGH HOLE IN PULL PLATE AND INSTALL
CASH BOX NUT FROM THE BACKSIDE OF THE PULL PLATE.
C. TIGHTEN CASH BOX NUT.
CASH BOX NUT
CYLINDER COLLAR
CYLINDER
SPACER
RING
WAVE SPRING
WASHER
MORTISE CYLINDER
(1-1/8" TO 1-3/8" LONG)
CASH BOX NUT TIGHTENED
TO CYLINDER
TRIM SPINDLE
1/2" MOUNTING HOLE
SCREW COLLAR
1/4"-20 FLAT HEAD
MACHINE SCREW
4700 EXIT DEVICE
1/4"-20 PAN HEAD MACHINE
SCREW (2X)
47BT
A. TRANSFER HORIZONAL CENTERLINE AND BACKSET
CENTERLINE FROM EXIT DEVICE SIDE OF DOOR
B. USE TEMPLATE TO MARK HOLE AND CUTOUT LOCATIONS.
NOTE THAT ONE HOLE AND A RECTANGULAR CUTOUT ARE
REQUIRED ON THE PULL SIDE AND FOUR HOLES ARE
REQUIRED FROM THE PUSH SIDE
C. CUT OUT THE RECTANGULAR AREA (8 7/16" X 2 1/8") SHOWN IN
THE TEMPLATE TO A DEPTH OF 1 3/8" ON THE PULL SIDE OF
THE DOOR (DEPTH CRITERIA APPLIES ONLY TO WOOD DOORS).
D. DRILL OUT THE 5/8" DIAMETER TRIM SPINDLE HOLE ON THE
PUSH SIDE OF THE DOOR.
E. DRILL THE MOUNTING HOLES PER THE TEMPLATE.
F. PLACE THE EXIT DEVICE IN ITS PROPER LOCATION.
G. INSERT PULL PLATE MOUNTING POSTS THROUGH THE DOOR
MAKING SURE THE TRIM SPINDLE INSERTS INTO THE EXIT
DEVICE.
H. SECURE THUMB PULL PLATE AND EXIT DEVICE USING THE
THREE MOUNTING SCREWS PROVIDED.
NOTES:
TRIM IS HANDED. SPECIFY WHEN ORDERING.
1.
DO NOT USE WAVE SPRING WASHER OR CYLINDER SPACER
2.
RING WITH 1 1/8" CYLINDERS.
47PT/47BT PULL PLATE INSTRUCTIONS
FOR USE WITH 4700 RIM AND SVR SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
REV: 01
DRAWING NO: I-ED01700
SHEET 1 OF 2
2 7/8"
72.9
9 13/16"
248.4
1 7/16"
36.4
7/16"
11.3
2 3/16"
55.9
1/16"
2
1 11/16"
42.5
3"
76.2
14 5/8"
371.5
1 1/2"
38.1
6 3/4"
171.6
5 15/16"
150.6
7/16"
11.2
PULL PLATE
C
L
CORRESPONDS TO
EXIT DEVICE
C
L
PULL PLATE
C
L
CORRESPONDS TO
EXIT DEVICE
C
L
NOTE:
DIMENSIONS IN BRACKETS [ ] ARE MILLIMETERS.
47PT/47BT PULL PLATE INSTRUCTIONS
FOR USE WITH 4700 RIM AND SVR SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
SHEET 2 OF 2
DRAWING NO: I-ED01700
REV: 01
  • Page 1 1
  • Page 2 2

Hagerco 47PT Operating instructions

Hagerco
Brand
Hagerco
Model
47PT
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents