Hagerco 45PD - Dummy Trim Operating instructions

Hagerco
Brand
Hagerco
Model
45PD - Dummy Trim
Category
Mounting kits
Type
Operating instructions

This manual is also suitable for

RIM CYLINDER
1-1/8" TO 1-3/8" LONG
IC OR STANDARD
CORE
WAVE
SPRING
WASHER
CYLINDER
SPACER
RING
CYLINDER COLLAR FOR
1-1/4 TO 1-3/8" LONG CYLINDERS
CYLINDER COLLAR - PROVIDED WITH CYLINDER
FOR 1-1/8" LONG CYLINDERS ONLY
CYLINDER CUP AND
TAILPIECE GUIDE
SPACER
STEP 1: INSTALL CYLINDER (SKIP TO STEP "2" FOR DUMMY PULL PLATE - 45PD)
INSTALL RIM CYLINDER THROUGH WAVE WASHER, CYLINDER SPACER
A.
RING (IF NEEDED) AND COLLAR. THE THINNER COLLAR PROVIDED WITH
THE RIM CYLINDER CAN BE USED FOR 1-1/8" LONG CYLINDERS ONLY.
INSERT RIM CYLINDER THROUGH HOLE IN PULL PLATE AND INSTALL
B.
SPACER AND CYLINDER CUP FROM THE BACKSIDE OF THE
PULL PLATE.
SECURE RIM CYLINDER ASSEMBLY USING THE 2 BREAK OFF SCREWS
C.
PROVIDED WITH THE RIM CYLINDER.
TAB MUST FIT INTO SLOT ON SPACER
TAB MUST FIT INTO SLOT ON
PULL PLATE
BREAK-OFF SCREWS
DOOR
SCREW COLLAR
1/4"-20 PAN HEAD
MACHINE SCREW (4X)
4500 EXIT DEVICE
HEAD CHASSIS
1/2" MOUNTING HOLES (5X)
1-3/4" CYLINDER HOLE (1X)
TRANSFER HORIZONTAL CENTERLINE AND BACKSET
A.
CENTERLINE FROM EXIT DEVICE SIDE OF THE DOOR.
USE TEMPLATE OR DIMENSIONS FROM PAGE 2 TO MARK
B.
HOLE LOCATIONS.
DRILL FIVE
1/2" CLEARANCE HOLES FOR MOUNTING POSTS.
C.
DRILL
1-3/4" CLEARANCE HOLE FOR THE CYLINDER.
D.
INSERT PULL PLATE MOUNTING POSTS THROUGH DOOR.
E.
RIM CYLINDER TAILPIECE SHOULD INSERT INTO THE EXIT DEVICE
F.
CAM APPROXIMATELY 7/16"
1/16". IF IT'S TOO LONG, CAREFULLY
MEASURE AND MARK AT THE CLOSEST BREAK-OFF LINE. THEN USE
PLYERS TO BREAK-OFF ACCESS, CAREFULLY NOT TO BREAK-OFF
TOO MUCH.
SECURE PULL PLATE AND EXIT DEVICE USING THE 5 MOUNTING
G.
SCREWS.
STEP 2: INSTALL PULL PLATE
1/4"-20 FLAT HEAD
MACHINE SCREW (1X)
BREAK-OFF SCREWS
PROVIDED WITH
RIM CYLINDER
45PN & 45PD PULL PLATE INSTRUCTIONS
FOR USE WITH 4500 SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
REV: 01
DRAWING NO: I-ED00263
SHEET 1 OF 2
.08
2
1.62
41.1
1.68
42.5
.45
11.3
1.49
37.9
.24
6
EXIT DEVICE
C
L
(SEE NOTE 1)
RIM CYLINDER
C
L
3.00
76.2
14.00
355.6
R
.75
19.1
5.93
150.6
2.44
61.9
2.89
73.5
2.74
69.6
4.38
111.1
2.19
55.6
2.19
55.6
.24
6
1.56
39.7
6.00
152.5
8.19
208.1
PULL PLATE
C
L
CORRESPONDS TO
EXIT DEVICE
C
L
REQUIRES A
0.50"
CLEARANCE HOLE
THROUGH DOOR (5X)
REQUIRES A
1.75"
CLEARANCE HOLE
THROUGH DOOR
PULL PLATE
C
L
CORRESPONDS TO
EXIT DEVICE
C
L
NOTES:
MATCH THIS CENTERLINE UP WITH THE EXIT DEVICE CENTERLINE.
1.
THIS WILL ENSURE THE RIM CYLINDER TAILPIECE LINES UP WITH THE
EXIT DEVICE TAILPIECE CAM.
45PN & 45PD PULL PLATE INSTRUCTIONS
FOR USE WITH 4500 SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
SHEET 2 OF 2
DRAWING NO: I-ED00263
REV: 01
  • Page 1 1
  • Page 2 2

Hagerco 45PD - Dummy Trim Operating instructions

Hagerco
Brand
Hagerco
Model
45PD - Dummy Trim
Category
Mounting kits
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents