Quadrafire Classic Bay 1200 Pellet Stove Installation guide

Type
Installation guide

Quadrafire Classic Bay 1200 Pellet Stove: Experience the warmth and convenience of a high-performing pellet stove, designed for effortless heating and efficient fuel usage. With its vertical centering adapter, heat shield, and clean-out feature, this stove offers optimal heat distribution and easy maintenance. Enjoy customizable installation options, thanks to the adjustable outer shield and multiple mounting points. Stay cozy and comfortable throughout the cold season with the Quadrafire Classic Bay 1200 Pellet Stove.

Quadrafire Classic Bay 1200 Pellet Stove: Experience the warmth and convenience of a high-performing pellet stove, designed for effortless heating and efficient fuel usage. With its vertical centering adapter, heat shield, and clean-out feature, this stove offers optimal heat distribution and easy maintenance. Enjoy customizable installation options, thanks to the adjustable outer shield and multiple mounting points. Stay cozy and comfortable throughout the cold season with the Quadrafire Classic Bay 1200 Pellet Stove.

7014-279A March 22, 2017 Page 1 of 2
1445 North Highway
Colville, WA 99114
www.quadrare.com
R
TOP VENT ADAPTER INSTALLATION INSTRUCTIONS
Vertical centering adapter with heat shield and clean out.
Part: TPVNT-1
C1
X1
Included in Kit:
Tools Required:
Electric drill, #26 drill bit (included), #2 Phillips screw-
driver, and high temp silicone (500° F).
C3
X1
C2
X6
5
(127)
2-1/2
(63)
For Free Standing Pellet Appliance:
CB1200
26
(661)
26
(661)
23-1/8
(586)
23-1/8
(586)
7014-279A March 22, 2017 Page 2 of 2
6. After performing regular cleaning of venting, open
the clean-out cover and vacuum out debris; close
when complete (Figure 6).
3. Ensuring the adapter is in the vertical position. Drill
4 holes with #26 drill bit (C3) into the back of the
stove using the outer shield on the adapter (C1) as
a guide. Secure using four mounting screws (C2)
(Figure 3).
Figure 3
Figure 4
4. Drill 2 holes with #26 drill bit (C3) through the
Exhaust Outlet using the 2 holes already in the short
horizontal pipe in the Top Vent Adapter as a guide.
Secure using two mounting screws (C2) (Figure 4).
5. Put a 1/4 inch bead of silicone on the outer edge of
the Top Vent Adapter (C1) exhaust outlet (Figure
5). Following venting manufacturing instructions,
install stove pipe to Top Vent Adapter (C1). (Note:
Appliance adapter from venting manufacture may
be required.) Do not apply silicone inside appliance
exhaust outlet.
2. Slide the Top Vent Adapter (C1) onto the exhaust
outlet over bead of silicone making sure the adapter
is in the vertical position. Slide the outer shield up or
down to align evenly with the top of stove. Tighten
the adjusting screws when the shield is in the proper
position (Figure 2).
Figure 2
Figure 5
Figure 6
Vent
Adapter
Drill holes in back of stove
and secure with 4 screws, 2
on each side.
Drill 1 hole on each side
and secure with mounting
screws
Silicone outer edge
Clean-Out Cover
1. Put a 1/4 inch bead of silicone on the outer edge
of the appliance exhaust outlet (Figure 1). Do not
apply silicone inside appliance exhaust outlet.
Figure 1
Silicone
Rear Exhaust
Outlet
  • Page 1 1
  • Page 2 2

Quadrafire Classic Bay 1200 Pellet Stove Installation guide

Type
Installation guide

Quadrafire Classic Bay 1200 Pellet Stove: Experience the warmth and convenience of a high-performing pellet stove, designed for effortless heating and efficient fuel usage. With its vertical centering adapter, heat shield, and clean-out feature, this stove offers optimal heat distribution and easy maintenance. Enjoy customizable installation options, thanks to the adjustable outer shield and multiple mounting points. Stay cozy and comfortable throughout the cold season with the Quadrafire Classic Bay 1200 Pellet Stove.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI