urmet domus MT124-017 Technical Manual

Brand: urmet domus

Model: MT124-017

Type: Technical Manual

START

sec.2a

−−−−

2GO! - Technical manual

PARAMETERS ..................................................................................2

PROGRAMMING BY KEYPAD .........................................................2

LANGUAGE MENU .......................................................................2

CONFIGURATION MENU .............................................................3

NAME MANAGEMENT MENU ......................................................3

DOOR OPENER CODE MENU ..................................................... 4

PROGRAMMING BY REMOTE IrDA DEVICE ................................... 5

PROGRAMMING BY MODEM .........................................................5

ERROR MESSAGES .........................................................................5

NORMAL OPERATION ERRORS .................................................5

INSTALLATION/PROGRAMMING ERRORS ................................5

SELF TEST ................................................................................... 5

PROGRAMMING MENU ..................................................................6

SECTION 2A

(REV.D)

CALLING MODULE

PROGRAMMING PROCEDURE

Download from www.urmetdomus.com Technical Manuals area.

SECTION CONTENTS

Some products may be described in the “New” section.§

CALLING MODULE PROGRAMMING PROCEDURE

START

−−−−

sec.2a

2GO! - Technical manual

CALLING MODULE PROGRAMMING

PROCEDURE

The calling module with repertory may be programmed as follows:

Locally, via the keypad, without opening the module frame.

Via remote Palm OS device provided with IrDA interface and

software downloadable from the site www.urmetdomus.com.

Via GSM modem Ref. 1082/52 and PC software downloadable

from the site www.urmetdomus.com.

PARAMETERS

The following parameters will need to be programmed:

1. OPERATING LANGUAGE

Up to 10 different operating languages can be selected.

2. NUMBER OF LINES

The number of lines managed by the device can be selected. The

device can manage one 2GO! line (up to 31 users) or two 2GO!

lines (up to 62 users).

3. SURVEILLANCE CAMERAS

This parameter enables external camera cycle function.

Surveillance camera can be connected to the door unit (terminals

V3, V5) using a relay box Ref. 1038/69 controlled by terminals T,

GND.

4. FIRST CODE

The admissible values for the ﬁ rst code are comprised in the range

from 1 to 62. The ﬁ rst code indicates the beginning of the range of

users who can operate the door lock also if no communication is

established (if free door opener function is enabled).

5. LAST CODE

The admissible values for the last code are comprised in the

range from 1 to 62. The last code indicates the end of the range of

users who can operate the door lock also if no communication is

established (if free door opener function is enabled).

6. SPECIAL CODE

The admissible values for the special code are comprised in the

range from 1000 to 9999. The special code is used to enable

the staircase light function, if a special decoder is present in the

system.

7. PASSWORD

The admissible values for the password are comprised in the

range from 1000 to 9999. The password is used to program the

calling module.

8. MODULE ID

This value indicates the module code. Possible values are 1, 2

and 3.

9. DOOR PHONE/VIDEO DOOR PHONE CODE

Admissible values are in the range from 1 to 99. The codes from 1

to 49 indicate that the device is provided with camera. The codes

from 50 to 99 indicate that the device is only a door phone. This

also indicates the remote device programming code.

10. LCD CONTRAST

The display contrast level of the display is set by default to an

optimal level. The setting can be changed if needed.

11. MODULE TYPE

The calling module may be a main device or a secondary

device. See the 2GO! system manual for main/secondary device

management.

12. DOOR OPENER MODE

Two door opener modes may be selected:

Privacy.

Free.

13. NAMES

Up to 186 names can be entered in the calling module. Refer to

the programming steps shown below for entering names.

•

14. DOOR OPENER CODES

Up to 100 door opener codes, unrelated to names, for general

use, can be stored in the calling module.

PROGRAMMING BY KEYPAD

Press / to scroll the various programming menus. Press to

conﬁ rm selections. Press X to quit.

Press 0 twice to access device programming mode. The following

message will appear:

Enter the password and press to conﬁ rm. The following message

will appear if the password is not correct:

Enter a correct password to access the multilevel menu shown below

and described next to the various screenshots.

The ﬁ rst menu level is:

LANGUAGE MENU

Select the language menu. The following will appear:

↓

•••••••••••••••••••••••••••••••••••••••••••••

Press / to select the required language. Press to conﬁ rm

selection. Press X to return to the ﬁ rst level menu.

CALLING MODULE PROGRAMMING PROCEDURE

PARAMETERS

PROGRAMMING BY KEYPAD

CALLING MODULE PROGRAMMING PROCEDURE

START

CALLING MODULE PROGRAMMING PROCEDURE

sec.2a

−−−−

2GO! - Technical manual

CALLING MODULE PROGRAMMING PROCEDURE

PROGRAMMING BY KEYPAD

CONFIGURATION MENU

Select the conﬁ guration menu to access the various setup options.

Each setting must be conﬁ rmed before accessing the following one.

Scroll all conﬁ gurations to quit the conﬁ guration menu.

The ﬁ rst conﬁ guration is:

↓

Use / to select the number of 2GO! wired to the device. Press

to select the option indicated by the cursor and go to the following

page:

Press / to select the surveillance cameras ﬁ tted in the system.

Press

to select the option indicated by the cursor and go to the

following page:

Use the keypad to enter the ﬁ rst system code. Two characters can be

entered. Use X to delete the character if you make a mistake. Press

to select the indicated option and go to the following page:

The ﬁ rst code and the last code identify which power unit (2GO! riser)

the users are connected to.

Use the keypad to enter the last system code. Two characters can be

entered. Use X to delete the character if you make a mistake. Press

to select the indicated option and go to the following page:

Enter the special code using the keypad. The special code is used to

activate special decoders ﬁ tted in the system. Four characters must

be entered. Use X to delete the character if you make a mistake. Press

to select the indicated option and go to the following page:

Enter the device password using the keypad. Four characters must be

entered. Use X to delete the character if you make a mistake.

Press to select the indicated option and go to the following page:

Enter the device ID code (1, 2 or 3) using the keypad. One character

can be entered. Use X to delete the character if you make a mistake.

Press to select the indicated option and go to the following page:

Enter the device remote programming code with the keypad. Two

characters can be entered. Use X to delete the character if you make

a mistake.

Press

to select the indicated option and go to the following page:

Press / to change the graphic display contrast. Press to conﬁ rm

contrast and go to the following page:

Use / to select whether the device is a main or a secondary device:

The selection is shown by the cursor. Press

to go to the following

page:

Use / to select the door opening type (free/privacy).

The selection is shown by the cursor. Press to end module

programming.

NAME MANAGEMENT MENU

Select the name management menu to access the following menu:

↓

Use / to select the option. Press to conﬁ rm. Press X to quit the

menu.

The name management second level menu options are:

↓

Use / to select the characters and press . to conﬁ rm. Press X to

delete a character if you make a mistake. Press X on a empty line to

return to the previous menu.

Press to conﬁ rm name selection. A name can be entered on two

lines (32 characters).

CALLING MODULE PROGRAMMING PROCEDURE

START

−−−−

sec.2a

2GO! - Technical manual

CALLING MODULE PROGRAMMING PROCEDURE

PROGRAMMING BY KEYPAD

The following message will appear if a name already exists:

The ﬁ eld for entering the code corresponding to the user will appear

if the name is correct:

Enter the code using the keypad. Press X to delete entry. Press X on

an empty line to return to name entry mode.

Press to conﬁ rm code selection.

The following message will appear if the code is wrong (code <1 or

>62):

The system will go to the next programming step if the code is

correct:

Enter the user’s door opener code using the keypad (optional). Press

X to delete a character if you make a mistake. Press X on an empty

line to return to the name entry step without adding the name.

Press to conﬁ rm the user’s name and code and the possible door

opener code.

The following will appear if the code is wrong (<4 digits or already

existent in the calling module):

The following page will appear if the door opener code is correct:

The new user is added to the database and the system returns to the

higher menu level.

The following steps are used to access the name editing menu:

↓

Press / to scroll the list of stored users. Press to edit the

selected name. The steps for editing a name are the same as those

for adding a new user.

Select the name deletion menu and selection the name to be deleted

(the procedure is the same as that for editing a user name).

Conﬁ rmation is required before deleting a selected name:

↓

Press to select the option indicated by the cursor. If the cursor is

pointing to YES, the system will return to the user menu step (add,

edit, delete) after deleting. If the cursor is pointing to NO, the system

will return to the name selection step

Conﬁ rmation is required before clearing all names:

↓

Press with cursor pointing to YES to clear the entire database (all

names, user codes and door opener codes) and go back to the user

menu step. Press with the cursor pointing to NO, to go back to the

higher menu level.

DOOR OPENER CODE MENU

Select the door opener code menu to access the following menu:

↓

Press / to scroll the various menu items. Press to conﬁ rm the

selection. Press X to quit the menu.

The door opener code management second level menu options are:

↓

CALLING MODULE PROGRAMMING PROCEDURE

START

CALLING MODULE PROGRAMMING PROCEDURE

sec.2a

−−−−

2GO! - Technical manual

CALLING MODULE PROGRAMMING PROCEDURE

PROGRAMMING BY REMOTE IrDA DEVICE

PROGRAMMING BY MODEM - ERROR MESSAGES

Enter the code using the keypad. Press to conﬁ rm code entry.

Press X to correct the door opener code. Press X on a empty line to

return to the previous menu.

The following will appear if the code is wrong (<4 digits or already

existent in the calling module):

The system will return to the code entry step. The correct code will be

added to the database and the door opener codes menu will appear

on the display.

The following steps are used to access the editing menu:

↓

Press / to scroll the list of stored door opener codes. Press

while the code is displayed to edit the code. The steps for editing a

code are the same as those for adding a new code.

Select the code deletion menu and selection of the code to be deleted

(the procedure is the same as that for editing a user name).

Conﬁ rmation is required before deleting a selected code:

↓

Press o select the option indicated by the cursor. Use / to move

the cursor. If the cursor is pointing to YES, the system will return to the

door opener code menu step (add, edit, delete) after deleting. If the

cursor is pointing to NO, the system will return to the code selection

step.

Conﬁ rmation is required before clearing all names:

↓

If conﬁ rmed, are deleted the 100 free door lock release codes.

PROGRAMMING BY REMOTE IrDA DEVICE

The calling module can also be programmed using a hand-held device

running appropriate software via the infrared port.

The software can be downloaded from the site

www.urmetdomus.com.

Proceed as follows to access the remote programming mode via the

IrDA port:

Press 0 twice to access programming mode.

Place the hand-held device near the infrared port of the device. The

following page will appear:

•

Access programming mode using the hand-held device. The

following page will appear:

Programming the calling module with the Palm Os device.

Press X to quit remote programming. The module will return to

stand-by mode.

PROGRAMMING BY MODEM

For programming by Modem refer to documentation on the site www.

urmetdomus.com.

For this programmation must be installed the interface

Ref. 1082/53.

ERROR MESSAGES

Various types of error messages may appear on the display.

NORMAL OPERATION ERRORS

Wrong calling code, door opener code, special code:

INSTALLATION/PROGRAMMING ERRORS

Module ID code error:

X is either A or B indicating the line on which another device with the

same code is present.

ONLY ONE main device may be present in a system (code ID 1).

Two secondary devices can be connected to each branch (2 on

each line).

The same message may appear in the event of a line error.

X may become either A or B in this case.

This type of error appears when line impedance parameters are not

correctly set (same function as the “yellow LED” on the 2GO! door

unit).

SELF TEST

The following will appear in the event of a language memory fault:

•

CALLING MODULE PROGRAMMING PROCEDURE

START

−−−−

sec.2a

2GO! - Technical manual

CALLING MODULE PROGRAMMING PROCEDURE

PROGRAMMING MENU

...........

FIRST CODE

...........

LAST CODE

...........

SPECIAL CODE

...........

PASSWORD

...........

MODULE ID

AUDIO/VIDEO

CODE

...........

LCD CONTRAST

TYPE MODULE

DOOR OPENER MODE

PASSWORD

LANGUAGE

CONFIGURATION

NAMES

DOOR OPEN. CODES

ITALIANO

LINE NUMBER

<1> <2>

ENGLISH

CAMERA CONTROL

CONFIRMATION?

CODE

...........

DOOR OPENIG COD

...........

INSERT NAME

...........

INSERT DOOR OPEN. CODES

...........

select the name

to be modified

then change the

shown

parameter

MODIFY

select the name

to be deleted

then press

DELETE

DOOR OPENING COD

XXXX

DELETE

CONFIRMATION?

DELETE ALL?

CONFIRMATION?

DELETE ALL?

CALLING MODULE PROGRAMMING PROCEDURE

urmet domus MT124-017 Technical Manual

Brand: urmet domus

Model: MT124-017

Type: Technical Manual

Download PDF

report

urmet domus MT124-017 Technical Manual

urmet domus MT124-017 Technical Manual

Related papers

Other documents