urmet domus MT124-017 Technical Manual

Brand
urmet domus
Model
MT124-017
Category
Door intercom systems
Type
Technical Manual

The urmet domus MT124-017 is a high-quality audio/video door entry system that allows you to see and speak to visitors at your door before granting them access. The system includes a sleek, modern design that will complement any home décor. With its built-in camera and microphone, you can easily identify visitors and communicate with them from the comfort of your own home. The system also features adjustable volume controls, so you can customize the sound level to your liking. Installation is simple and straightforward, and the system is compatible with most existing door entry systems.

The urmet domus MT124-017 is a high-quality audio/video door entry system that allows you to see and speak to visitors at your door before granting them access. The system includes a sleek, modern design that will complement any home décor. With its built-in camera and microphone, you can easily identify visitors and communicate with them from the comfort of your own home. The system also features adjustable volume controls, so you can customize the sound level to your liking. Installation is simple and straightforward, and the system is compatible with most existing door entry systems.

sec.4a
−−−−
1
2GO! - Technical manual
APARTMENT
VIDEO DOOR PHONE
STATIONS
SECTION 4A
(REV.E)
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1 2
SPECIFICATIONS - TECHNICAL FEAUTURES ...............................2
BRACKET Ref. 1703/82 ...................................................................3
Bracket terminal board .................................................................3
Technical feautures Ref. 1703/701 ...............................................3
Default programming ....................................................................3
INSTALLATION .................................................................................3
TONE SELECTION ...........................................................................4
Door phone call tone ....................................................................4
Floor call tone ...............................................................................5
Programming data deletion ..........................................................5
ACCESSORIES FOR UTOPIA VIDEO DOOR PHONES ................... 5
ATLANTICO BLACK/WHITE VIDEO DOOR PHONE 6
SPECIFICATIONS - TECHNICAL FEAUTURES ...............................6
ATLANTICO COLOUR VIDEO DOOR PHONE Ref. 1702/40 7
SPECIFICATIONS - TECHNICAL FEAUTURES ...............................7
ATLANTICO VIDEO DOOR PHONE 8
BRACKET Ref. 1702/82 ...................................................................8
Bracket terminal board .................................................................8
Technical feautures Ref. 1702/701 ...............................................8
Default programming ....................................................................8
INSTALLATION ................................................................................8
TONE SELECTION ...........................................................................9
Door phone call tone ....................................................................9
Floor call tone ...............................................................................9
Programming data deletion ..........................................................9
ACCESSORIES FOR ATLANTICO VIDEO DOOR PHONES .............9
Add-on Ref. 1082/96 ....................................................................9
Coloured mask kit Ref. 1702/50 .................................................10
Download from www.urmetdomus.com Technical Manuals area.
SECTION CONTENTS
Some products may be described in the “New” section.§
ARTICO VIDEO DOOR PHONE Ref. 1705/1 11
SPECIFICATIONS - TECHNICAL FEAUTURES .............................11
BRACKET Ref. 1705/82 .................................................................12
Bracket terminal board ...............................................................12
Technical feautures Ref. 1705/701 .............................................12
Default programming ..................................................................12
INSTALLATION ...............................................................................12
TONE SELECTION .........................................................................13
Door phone call tone ..................................................................13
Floor call tone .............................................................................13
Programming data deletion ........................................................13
FRONT GLASS REPLACEMENT .................................................... 13
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE
VIDEO DOOR PHONE 14
SPECIFICATIONS - TECHNICAL FEAUTURES .............................14
TERMINALS BOARD DESCRIPTION .............................................15
DEFAULT PROGRAMMING ...........................................................15
INSTALLATION ...............................................................................15
On brick walls .............................................................................15
On plasterboard walls .................................................................15
MAIN MENU FUNCTION ................................................................16
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE
Ref. 1703/4 17
SPECIFICATIONS - TECHNICAL FEAUTURES .............................17
BRACKET Ref. 1703/84 .................................................................18
Bracket terminal board ...............................................................18
Technical feautures ....................................................................18
Default programming ..................................................................18
WALL-MOUNTED INSTALLATION .................................................18
FLUSH-MOUNTED VERSION INSTALLATION ..............................19
INSTALLATION ON PLASTERBOARD WALLS ..............................21
ACCESSORIES FOR UTOPIA VIDEO DOOR PHONES ................. 22
APARTMENT VIDEO DOOR PHONE STATIONS
2
−−−−
sec.4a
2GO! - Technical manual
UTOPIA COLOUR VIDEO DOOR PHONE
Ref. 1703/1
The Utopia video door phone is a colour device with an elegant,
revolutionary style and a particularly slim profi le (protruding only 55
millimetres from the wall) designed by Studio De Lucchi.
Some settings are arranged under the front sliding cover to make the
design more streamline and convenient.
Standard controls of Utopia, in addition to colour, brightness and
contrast, include three auxiliary buttons and indication LED.
The video door phone is easy to install because no masonry work
is needed and all connections are made to the bracket on which
the video door phone will eventually be fastened. The handset is
connected simply by means of a telephone plug.
The video door phone Ref. 1703/17 is set up to a speaker
capable interfacing with hearing aids by means of the “T”
function.
SPECIFICATIONS
The main features of the video door phone are:
Flat 4” TFT backlit colour module.
Call speaker separate from handset.
Adjustable call volume: when the call volume selector is in “MUTE”
(
) position, the corresponding LED lights up to indicate that the
call tone has been inhibited. The LED is visible also when the front
panel is closed.
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
Adjustable colour and brightness of the picture by means of a
slider.
Adjustable contrast by means of a trimmer positioned under the
sliding front panel.
Two additional buttons ( , ) for programming, auto power-on,
special decoder activation for secondary electrical locks, staircase
lights, etc.
Button : press this button to activate the “automatic door
opener” function. A door opener command will be sent when a
call is received from a door unit. The red LED indicates when the
function is on.
Door opener button: simply press the button to operate the door
lock ( ); the button will remain lit as long as the picture appears
on the video door phone.
Open door indicator: a red LED lights up when the door is open if
the system is set up for this function.
•
•
•
§
•
•
•
•
•
•
1
3
2
4
5
55 mm180 mm
9
10
8
6
7
225 mm
1
Auxiliary buttons
2
Button for automatic door opener function
3
Contrast adjustment control
4
Brightness adjustment control
5
Colour adjustment trimmer
6
Call tone adjustment trimmer
7
Door opener button
8
Automatic door opener function LED
9
Mute function led
10
Open door led
TECHNICAL FEAUTURES
Power voltage: 16 ÷ 18,5Vcc
Working Uptake: max 0,36A
Stand-by: 0A
Working power: max 6,5W
CCIR Version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75Ω nominal
1Vpp -6 dB minimum
LCD: 4” backlit
Screen size: 81 x 59mm
Resolution: 380H x 250V pixel
Colour system: PAL
Switch-on delay: 4 sec. max.
Transmitting capsule: electret microphone
Receiving capsule: speaker 45Ω
Button voltage: 24Veff. max.
Button current: 1,2Aeff.
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
SPECIFICATIONS
TECHNICAL FEAUTURES
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
3
2GO! - Technical manual
BRACKET Ref. 1703/82
The Utopia video door phone Ref. 1703/1 is supplied without bracket
that must be purchased separately.
The bracket fi ts connection terminals, programming dip switches and
line terminal switch.
A yellow LED is provided for checking correct reception of the Video
signal. The LED comes on if reception is not optimal.
1 2 3 4 5
ON
1 2
ONDIP
32
1
4
5
1
Line terminal switch
2
Terminal board
3
User code dip switch (CODE)
4
Apartment internal code dip switch (INT)
5
Yellow indicator LED
Kit Ref. 1703/701 including the following devices:
System 2GO! bracket Ref. 1703/82
One-user distributor Ref. 1082/51
The one-user distributor must be installed only for video door
phones connected in extension confi guration. The distributor is
not required with connections in in-out confi guration.
BRACKET TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
To use the fl oor call or supplementary ringer function, remove the
dedicated terminal protection and connect the respective wires.
TECHNICAL FEAUTURES Ref. 1703/701
Max. bracket draw with monitor on: 550mA
Max. bracket draw in standby: 11mA
One-user distributor draw: 8 ÷ 12mA
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
•
•
§
INSTALLATION
Proceed as follows to install the Utopia video door phone:
1. Arrange the duct so that it ends in correspondence with one of the
input holes.
2. Remove bracket protection.
NO
3. Arrange the bracket on wall considering height from ground and
side clearance.
155 cm
7 cm
6 cm
10 cm
10 cm
NO
4. Fasten the bracket to the wall using the bolt provided.
Alternatively fasten the bracket to a fl ush-mounting box using the
specifi c holes.
NO
NO
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
BRACKET Ref. 1703/82
INSTALLATION
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
APARTMENT VIDEO DOOR PHONE STATIONS
4
−−−−
sec.4a
2GO! - Technical manual
5. Connect the wires to the specifi c terminals.
6. Confi gure the dip switches as shown in the “System installation
and activation” section.
Complete system installation and power the system up before
fastening the video door phone to the bracket.
Check that the yellow LED on the brackets is off. Otherwise
proceed as follows:
Check correct setting of line terminal.
Check programmed settings of apartment stations and
brackets.
Split the system up to isolate the part which generates Video
signal transmission and reception problems.
Power the system and check that the yellow LEDs go out. Then refi t
the clip-on cover onto the bracket. Remove the cover only before
fi tting the Utopia video door phone on the bracket.
NO
1. Remove the protective cover from the bracket.
NO
B
B
§
•
•
•
2. Fit the Utopia video door phone on the bracket as follows:
2.1 Fasten the video door phone to the hooks B on the upper side
of the bracket.
2.2 Turn the video door phone downwards.
2.3 Shut the video door phone on the bracket and ensure that
fastening lever C is blocked.
B
C
Press lever C and reverse the sequence to remove the video
door phone.
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the Door opener button when you have chosen the tone
you want. The tone is now programmed.
The selected tone will be the same for all door phone calls. The source
of the call can however be distinguished by timing the tone:
Call origin Time
Call from main door unit 3s ON
Call from secondary door unit
0,4s ON-0,2s OFF for 5 times
Intercom call 0,5s ON-0,5s OFF for 5 times
§
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
TONE SELECTION
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
5
2GO! - Technical manual
FLOOR CALL TONE
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the Door opener button when you have chosen the tone
you want. The tone is now programmed.
The fl oor call timing is fi xed (3 seconds).
PROGRAMMING DATA DELETION
Proceed as follows to delate all optional programming data:
1. Hold the door opener button pressed and pick-up the handset.
2. Press and on the video door phone at the same time for 3
seconds until you hear the deletion tone.
3. Release buttons on the video door phone and hang up.
ACCESSORIES FOR UTOPIA VIDEO DOOR
PHONES
The video door phone can be customised by replacing the front fl aps
with the following models:
Yellow Ref. 1703/51
Green Ref. 1703/52
Anthracite black Ref. 1703/53
Replace by removing the sliding protection fl aps.
Refi t the protective fl aps.
•
•
•
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
UTOPIA COLOUR VIDEO DOOR PHONE Ref. 1703/1
ACCESSORIES FOR UTOPIA VIDEO DOOR PHONES
APARTMENT VIDEO DOOR PHONE STATIONS
6
−−−−
sec.4a
2GO! - Technical manual
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” black and white video module.
Adjustable and mutable call volume. The adjustment wheel appears
red when the volume is muted.
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
Door opener button is lit up when video module is on.
Two additional buttons ( and ) for programming, auto power-
on, special decoder activation for secondary electrical locks,
staircase lights, etc.).
Adjustable brightness and contrast.
Door opener button
Auxiliary service/
Intercom call buttons
Auto-on/
Intercom call button
Call volume/
Mute function
Contrast adjustment
Brightness adjustment
218 mm
220 mm
80 mm
TECHNICAL FEAUTURES
Power voltage: 16 ÷ 18,5Vcc
Working Uptake: max 0,35Acc
Stand-by: 0A
Working power: max 6,5W
CCIR Version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75Ω nominal
1Vpp -6dB minimum
Kinescope: 4” fl at 13mm neck
Phosphorous: P45
Screen size: 81 x 59mm
Geometric distorsion: vert. 5% max.
horiz. 5% max.
barrel 10% max.
Brightness: 170cd/m
2
max. setting.
X-rays: none
Switch-on delay: 4 sec. max.
Transmitting capsule: electret microphone
Receiving capsule: speaker 45Ω
Button voltage: 24Veff. max.
Button current: 1,2 Aeff.
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR
•
•
§
•
•
•
ATLANTICO BLACK/WHITE VIDEO DOOR
PHONE
The Atlantico video door phone has innovative simple, essential
designed fashioned by Michele De Lucchi. The following version are
available:
White Ref. 1702/1
Anthracite Ref. 1702/41
High Tech Grey Ref. 1702/42
The front mask colour can be changed with the kit Ref. 1702/50 to suit
the video door phone for all architectural context.
The video door phone is easy to install because no masonry work is
needed and all connections are made to the bracket on which the
video door phone will eventually be fastened.
The handset connection is particularly ergonomic. A simple telephone
plug is used.
The call volume (to dedicated speaker) can be adjusted in linear
fashion and muted.
The Door opener button by the side of the handset is lit up and green
when the monitor is on.
The video door phone Ref. 1702/17 is set up to a speaker
capable interfacing with hearing aids by means of the “T”
function.
•
•
•
ATLANTICO BLACK/WHITE VIDEO DOOR PHONE
ATLANTICO BLACK/WHITE VIDEO DOOR PHONE
SPECIFICATIONS
TECHNICAL FEAUTURES
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
7
2GO! - Technical manual
ATLANTICO COLOUR VIDEO DOOR PHONE
Ref. 1702/40
The Atlantico video door phone is a colour apartment station which can
be used in 2GO! systems when equipped with the specifi c bracket.
As the black and white version, also this model has adjustable call
tone volume and muting functions.
The video door phone is easy to install because no masonry work is
needed and all connections are made to the bracket on which the
video door phone will eventually be fastened. The handset connection
is particularly ergonomic. A simple telephone plug is used.
The video door phone is only white but the front part can be customised
by replacing the standard frame (blue) with one of the fi ve frames from
the Ref. 1702/50 kit.
The video door phone Ref. 1702/47 is set up to a speaker
capable interfacing with hearing aids by means of the “T”
function.
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” LCD colour module.
Adjustable and mutable call volume. The adjustment wheel appears
red when the volume is muted.
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
Door opener button is lit up when video module is on.
Two additional buttons ( and ) for programming, auto power-
on, special decoder activation for secondary electrical locks,
staircase lights, etc.).
Adjustable brightness and colour.
Door opener button
Auxiliary service/
Intercom call buttons
Auto-on/
Intercom call button
Call volume/
Mute function
Colour adjustment
Brightness adjustment
218 mm
220 mm
80 mm
TECHNICAL FEAUTURES
Power voltage: 16 ÷ 18,5Vcc
Working Uptake: max 0,35A
Stand-by: 0A
Working power: max 6,5W
CCIR Version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75Ω nominal
1Vpp -6dB minimum
LCD: 4” backlit
Screen size: 81 x 59mm
Resolution: 380H x 250V pixel
Colour system: PAL
Switch-on delay: 4 sec. max.
Transmitting capsule: electret microphone
Receiving capsule: speaker 45Ω
Button voltage: 24Veff. max.
Button current: 1,2Aeff.
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR
•
•
§
•
•
•
ATLANTICO COLOUR VIDEO DOOR PHONE Ref. 1702/40
ATLANTICO COLOUR VIDEO DOOR PHONE Ref. 1702/40
SPECIFICATIONS
TECHNICAL FEAUTURES
APARTMENT VIDEO DOOR PHONE STATIONS
8
−−−−
sec.4a
2GO! - Technical manual
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
INSTALLATION
Proceed as follows to install the Atlantico video door phone and the
respective bracket:
1. Arrange the duct so that it ends in correspondence with one of the
input holes.
2. Fasten the bracket to the wall at the height from the fl oor shown
by means of the four screws.
1 2
ON
1 2 3 4 5
ON DIP
1,55 m
3. Connect the wires to the specifi c terminals.
4. Confi gure the dip switches as shown in the “System installation
and activation” section.
Complete system installation and power the system up before
fastening the video door phone to the bracket.
Check that the yellow LED on the brackets is off. Otherwise
proceed as follows:
Check correct setting of line terminal.
Check programmed settings of apartment stations and
brackets.
Split the system up to isolate the part which generates Video
signal transmission and reception problems.
5. Extract the retainer hook A by inserting the tip of a screwdriver
and pulling the hook downwards.
6. Fasten the video door phone to the bracket as shown in the
fi gure.
The switch can be either in position “A” or in position “B” on
video door phones.
7. Fasten the video door phone by pushing the retainer hook A
upwards.
A
§
•
•
•
§
BRACKET Ref. 1702/82
The Atlantico video door phone is supplied without bracket that must
be purchased separately.
The bracket fi ts connection terminals, programming dip switches and
line terminal switch.
A yellow LED is provided for checking correct reception of the Video
signal. The LED comes on if reception is not optimal.
1 2
ON
1 2 3 4 5
ON DIP
3
4
2
5
6
1
1
Yellow indicator LED
2
Connector for Ref. 1082/96 add-on
3
User code dip switch (CODE)
4
Apartment internal code dip switch (INT)
5
Line terminal switch
6
Terminal board
Kit Ref. 1702/701 including the following devices:
System bracket Ref. 1702/82
One-user distributor Ref. 1082/51
The one-user distributor must be installed only for video door
phones connected in extension confi guration. The distributor is
not required with connections in in-out confi guration.
BRACKET TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
To use the fl oor call or supplementary ringer function, remove the
dedicated terminal protection and connect the respective wires.
TECHNICAL FEAUTURES Ref. 1702/701
Max. bracket draw with monitor on: 550mA
Max. bracket draw in standby: 11mA
One-user distributor draw: 8 ÷ 12mA
•
•
§
ATLANTICO VIDEO DOOR PHONE
ATLANTICO VIDEO DOOR PHONE
BRACKET Ref. 1702/82
INSTALLATION
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
9
2GO! - Technical manual
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the Door opener button when you have chosen the tone
you want. The tone is now programmed.
The selected tone will be the same for all door phone calls. The source
of the call can however be distinguished by timing the tone:
Call origin Time
Call from main door unit 3s ON
Call from secondary door unit
0,4s ON-0,2s OFF for 5 times
Intercom call 0,5s ON-0,5s OFF for 5 times
FLOOR CALL TONE
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the Door opener button when you have chosen the tone
you want. The tone is now programmed.
The fl oor call timing is fi xed (3 seconds).
PROGRAMMING DATA DELETION
Proceed as follows to delate all optional programming data:
1. Hold the door opener button pressed and pick-up the handset.
2. Press and on the video door phone at the same time for 3
seconds until you hear the deletion tone.
3. Release buttons and hang up.
ACCESSORIES FOR ATLANTICO VIDEO DOOR
PHONES
ADD-ON Ref. 1082/96
A special add-on module Ref. 1082/96 can be purchased separately
and combined with basic monitors in intercom systems where up to 6
buttons, 2 LEDs and a switch are required.
FUNCTION
6
5
4
3
2
1
6
5
4
3
2
1
Red Led
Green Led
AUTOMATIC DOOR OPENER FUNCTION
This function can be switched on and off by means of the dedicated
button on the Ref. 1082/96 add-on. The green LED will light up
when the function is on. A door opener command is transmitted when
a call from a door unit is received. Program this function on one of the
indoor stations only if there are several indoor stations in parallel.
MASTER DOOR UNIT OPEN DOOR FUNCTION
The indoor stations can monitor the physical state of the Master door
by connecting a sensor to the SP/GND terminals. The red LED on the
Ref. 1082/96 will light up when the door is open.
INTERCOM CALL FORWARDING
This function is similar to the basic function illustrated for the buttons
and . Six buttons can be programmed for managing the same
number of calls.
INSTALLATION
Fasten the add-on to the bracket using the plates provided.
Open the add-on top.
REAR VIEW
•
•
ATLANTICO VIDEO DOOR PHONE
ATLANTICO VIDEO DOOR PHONE
TONE SELECTION
ACCESSORIES FOR ATLANTICO VIDEO DOOR PHONES
APARTMENT VIDEO DOOR PHONE STATIONS
10
−−−−
sec.4a
2GO! - Technical manual
Connect the fl at wire provided to the video door phone bracket.
Fasten the monitor to the bracket after connecting: extract fastening
hook A to fasten the monitor; fasten it to the bracket and block it by
pushing the hook A inwards.
A
Close the add-on top.
Remove the clear plastic cover to access the name tags.
6
5
4
3
2
1
COLOURED MASK KIT Ref. 1702/50
The video door phone can be customised by replacing the front mask
and add-on name tag with those contained in the Ref. 1702/50 kit.
The kit contains masks and cards of the following colours:
Yellow
Pink
Grey
Green
Blue
Besides the coloured frames the kit contains a protective smoke grey
cover.
The video door phone grey and blue frames are combined with
name tags with a white background and coloured lines.
•
•
•
•
•
•
•
•
•
§
A
B
C
D
E
1
2
F
Other media, such as photographs or wall paper, can be use to
customize the video door phone instead of 1702/50 kit. In this case
use one of the frames provided as a template to trace the exact
installation profi le.
ATLANTICO VIDEO DOOR PHONE
ATLANTICO VIDEO DOOR PHONE
ACCESSORIES FOR ATLANTICO VIDEO DOOR PHONES
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
11
2GO! - Technical manual
ARTICO VIDEO DOOR PHONE Ref. 1705/1
Artico offers the most modern technology applied to picture display
and the best quality/price ratio. These features make the video
door phone suitable for normal communication needs and security
applications in video door phone systems.
Thanks to the use of a functional fl at 4” screen which reduces the
protrusion from the wall, Artico can be installed on the wall without
the need for masonry work.
Connection of this video door phone are also simple and rapid, thanks
to the terminal board arranged on the dedicated bracket.
The video door phone Ref. 1705/17 is set up to a speaker
capable interfacing with hearing aids by means of the “T”
function.
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” black and white video module.
Adjustable and mutable call volume. The adjustment wheel appears
red when the volume is muted.
MUTEMEDMAX
Door opener button dedicated.
Two additional buttons ( , for programming, auto power-on,
special decoder activation for secondary electrical locks, staircase
lights, etc.).
Adjustable brightness and contrast.
•
•
•
•
•
200 mm
241 mm
83 mm
1
2
3
4 65
1
Door opener button
2
Auxiliary button: used for special functions
3
Auxiliary button: used for special functions
4
Contrast adjustment control
5
Brightness adjustment control
6
Call volume control and adjustment: turn the knob as far as it will
go (red part visible) to mute the call tone (“MUTE” function)
TECHNICAL FEAUTURES
Power voltage: 16 ÷18,5Vcc
Working Uptake: max 0,6A
Stand-by: 0 A
Working power: max 10W
CCIR Version Vertical frequency: 50 Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75Ω nominal
1Vpp -6 dB minimum
Kinescope: 4” fl at 20mm neck
Phosphorous: P45
Screen size: 81 x 59mm
Geometric distorsion: vert. 5% max
horiz. 5% max
barrel 10% max
Brightness: >100cd/m
2
max. setting
X-rays: none
Switch-on delay: 7 sec. max
Transmitting capsule: electret microphone
Receiving capsule: speaker 45Ω
Button voltage: 24Veff. max
Button current: 1,2Aeff
Operating temperature range: -5° ÷ +50°C
Max. humidity: 90% UR
ARTICO VIDEO DOOR PHONE Ref. 1705/1
ARTICO VIDEO DOOR PHONE Ref. 1705/1
SPECIFICATIONS
TECHNICAL FEAUTURES
APARTMENT VIDEO DOOR PHONE STATIONS
12
−−−−
sec.4a
2GO! - Technical manual
BRACKET Ref. 1705/82
The Artico video door phone is supplied without bracket that must be
purchased separately.
1 2 3 4 5
ON
1 2
ONDIP
1 2 3 4 5
ON
1 2
ONDIP
1
3
4
5
2
1
Yellow indicator LED
2
User code dip switch (CODE)
3
Apartment internal code dip switch (INT)
4
Line terminal switch
5
Terminal board
Kit Ref. 1705/701 including the following devices:
System bracket Ref. 1705/82
One-user distributor Ref. 1082/51
The one-user distributor must be installed only for video door
phones connected in extension confi guration. The distributor is
not required with connections in in-out confi guration.
BRACKET TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
To use the fl oor call or supplementary ringer function, remove the
dedicated terminal protection and connect the respective wires.
TECHNICAL FEAUTURES Ref. 1705/701
Max. bracket draw with monitor on: 800mA
Max. bracket draw in standby: 11mA
One-user distributor draw: 8 ÷ 12mA
•
•
§
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
INSTALLATION
Proceed as follows to install the Artico video door phone and the
respective bracket:
1. Arrange the duct so that it ends in correspondence with one of the
input holes.
2. Fasten the bracket to the wall at the height from the fl oor shown
by means of the four screws.
Ref. 1705/82
A
1
2
3
4
5
ON
1
2
ON
DIP
1,55 m
3. Connect the wires to the specifi c terminals.
4. Confi gure the dip switches as shown in the “System installation
and activation” section.
Complete system installation and power the system up before
fastening the video door phone to the bracket.
Check that the yellow LED on the brackets is off. Otherwise
proceed as follows:
Check correct setting of line terminal.
Check programmed settings of apartment stations and
brackets.
Split the system up to isolate the part which generates Video
signal transmission and reception problems.
5. Extract the retainer hook A by inserting the tip of a screwdriver
and pulling the hook downwards.
6. Fasten the monitor to the bracket as shown in the fi gure.
The switch can be either in position “A” or in position “B” on
video door phones.
7. Fasten the video door phone by pushing the retainer hook A
upwards.
§
•
•
•
§
ARTICO VIDEO DOOR PHONE
ARTICO VIDEO DOOR PHONE Ref. 1705/1
BRACKET Ref. 1705/82
INSTALLATION
Ref. 1705/1
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
13
2GO! - Technical manual
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the Door opener button when you have chosen the tone
you want. The tone is now programmed.
The selected tone will be the same for all door phone calls. The source
of the call can however be distinguished by timing the tone:
Call origin Time
Call from main door unit 3s ON
Call from secondary door unit
0,4s ON-0,2s OFF for 5 times
Intercom call 0,5s ON-0,5s OFF for 5 times
FLOOR CALL TONE
1. Hold the door opener button pressed. Press and release the
button . The indoor station will play a tone.
2. Hold the door opener button pressed and press the button
again to change the tone.
3. Release the Door opener button when you have chosen the tone
you want. The tone is now programmed.
The fl oor call timing is fi xed (3 seconds).
PROGRAMMING DATA DELETION
Proceed as follows to delate all optional programming data:
1. Hold the door opener button pressed and pick-up the handset.
2. Press and on the video door phone at the same time for 3
seconds until you hear the deletion tone.
3. Release buttons and hang up.
FRONT GLASS REPLACEMENT
The video door phone can be customised by replacing the front
glass.
The following colours are available:
Smoky grey: Ref. 1705/101
(pre-fi tted on the video door phone)
Blue: Ref. 1705/102
A B
C D
•
•
ARTICO VIDEO DOOR PHONE Ref. 1705/1
ARTICO VIDEO DOOR PHONE Ref. 1705/1
TONE SELECTION
FRONT GLASS REPLACEMENT
APARTMENT VIDEO DOOR PHONE STATIONS
14
−−−−
sec.4a
2GO! - Technical manual
FOLIO FLUSH-MOUNTED COLOUR HANDS-
FREE VIDEO DOOR PHONE
The Folio video door phone is a fl ush-mounted colour device with
hands-free audio function.
It protrudes only a few millimetres from the wall and its style suggestive
of the Simon Urmet Nea wiring accessory design. It has a shiny “iPod
effect” front panel.
All settings are simply and intuitively made on an OSD (On Screen
Display) menu with graphic icons and integrated textual descriptions
using a handy four-position joypad.
The internal name directory, programmable by the user, may be used
to establish intercom calls to all users in the 2GO! system. The calling
method is similar to that of a mobile telephone.
Folio may be customised by the user by changing, for instance, the
display colours and themes and programming a different ring tone for
different call types.
The only buttons on the front panel in addition to the joypad are
those used to access the menu, switch audio on and off and open
the door.
The Folio come in two versions of different colour:
Black front Ref. 1706/1
White front Ref. 1706/2
SPECIFICATIONS
The main features of the video door phone are:
Flat 3.5” LCD backlit colour module.
Wide viewing angle in all directions also without mechanical tilting.
Call speaker separate from audio speaker.
4 backlit icons for activating various functions arranged by the two
sides of the display.
Backlit buttons with RGB variable colour LED programmable by
the user.
Automatic door opening function activatable from menu: a door
opening command is sent when a call is received from a door unit.
A LED indicates when the function is on.
Adjustable audio volume and call volume with muting function.
Adjustable brightness and contrast from menu.
Use mild detergents for delicate surfaces and a soft cloth
to clean the front panel of the video door phone. Do not use
abrasive materials.
•
•
•
•
•
•
•
•
•
•
§
1
2
3
4
5
6
7
8
9
10
Video door phone mode
Display
Door open indicator led on master station
Mute indicator led
Audio on indicator led
Automatic door opener on indicator led
Door opener button
Function button
Microphone
Audio button
MUTE on/off
Staircase light switch
Switchboard call
Automatic switch-on
1
2
3
9
10
4
5
6
8
Access menu
7
Menu
mode
Quit
Menu
OK
X
TECHNICAL FEAUTURES
Power voltage: 30Vcc
Working Uptake: 400mA max
Stand-by: 11mA
Working power: 1,5W max
CCIR Version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75Ω nominal
1Vpp -6dB minimum
LCD: 3.5” backlit
Horizontal viewing angle: +60° ÷ -60°
Vertical viewing angle +50° ÷ -55°
Brightness: >250cd/m
2
Screen size: 70 x 52mm
Resolution: 320H x 240V pixel
Colour system: PAL
Switch-on delay: 4 sec. max
Transmitting capsule: electret microphone
Receiving capsule: speaker 45Ω
Operating temperature range: -5° ÷ +45°C
Max. humidity: 95% UR
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE VIDEO DOOR PHONE
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE VIDEO DOOR PHONE
SPECIFICATIONS
TECHNICAL FEAUTURES
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
15
2GO! - Technical manual
TERMINALS BOARD DESCRIPTION
LINE
}
Non-polarised bus line
LINE
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
INSTALLATION
ON BRICK WALLS
For installing the Folio video door phone on brick walls, purchase
the specifi c box Ref. 1706/60 and fi x it to the wall at a height of
approximately 1,55 - 1,60m from the fl oor.
Then fi x the video door phone to the fl ush-mounting box by means of
the four screws provided and snap the front panel onto the support.
Remove the protective fi lm at the end of the operation.
After installation, the device will protrude by 8mm from the wall.
The frame dimensions on the wall are 148 x 170mm. The fl ush-
mounting depth is equal to 58mm.
§
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE VIDEO DOOR PHONE
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE VIDEO DOOR PHONE
TERMINALS BOARD DESCRIPTION
DEFAULT PROGRAMMING - INSTALLATION
ON PLASTERBOARD WALLS
For installing the Folio video door phone on plasterboard
walls, purchase kit Ref. 1706/61 in addition to the specifi c box
Ref. 1706/60.
Proceed as follows:
Break the wall at a height of approximately 1,55 - 1,60m from the
fl oor according to the dimensions shown in the following drawing.
13,5 cm
13,5 cm
155 cm
Fit the kit components on the fl ush-mounting box.
Ref. 1706/60
Insert the box in the hole.
•
•
•
APARTMENT VIDEO DOOR PHONE STATIONS
16
−−−−
sec.4a
2GO! - Technical manual
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE VIDEO DOOR PHONE
FOLIO FLUSH-MOUNTED COLOUR HANDS-FREE VIDEO DOOR PHONE
MAIN MENU FUNCTION
Fasten the screws of the kit to secure the box.
Then fi x the video door phone to the fl ush-mounting box by means
of the four screws provided and snap the front panel onto the
support.
Remove the protective fi lm at the end of the operation.
•
•
•
MAIN MENU FUNCTION
The MAIN MENU function may be activated when the system is in
stand-by mode.
Press the MENU button to switch the video door phone on. The main
menu will appear.
(The video door phone will generate a sequence of consecutive beeps
and will not light up if the MENU button is pressed while the system is
busy. This means that the line is busy because another conversation
is in progress. Try again later).
IMPORTANT: Remember that the video door phone will be switched
off when a call to any user in the system is received from the door
unit.
Use the ‘function’ button (↑↓) to select the required function and press
(OK) to confi rm.
The available functions are:
1. Video door phone answering service: This function uses the
corresponding video door phone answering service functions
where fi tted in the system.
2. Intercom service: The list of users to which intercom calls can
be made will appear automatically when this function is selected.
Select a name and press OK to make the call.
3. Automatic door opener: This function is used to automatically
operate the door lock when a call is received from a door unit.
4. Settings: Select this function to access the submenu used to
adjust and set the video door phone.
A. Audio settings
B. Video settings
C. Button backlighting
D. Change screen theme
E. Select ring tone
F. Edit name directory
G. Restore default settings
5. Change language: Select this function to display a list of the
available languages. Select a language and press OK to change
the interface dialogue language.
Refer to the manual supplied to the product for more information
on operation and Folio video door phone customisations.
§
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
17
2GO! - Technical manual
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
SPECIFICATIONS
TECHNICAL FEAUTURES
UTOPIA FREE-HANDS COLOUR VIDEO DOOR
PHONE Ref. 1703/4
The Utopia video door phone is a colour device with an elegant,
revolutionary style and a particularly slim profi le designed by Studio
De Lucchi.
The most outstanding feature of this video door phone is that it is a
free-hands model without handset.
Communication is established by pressing the button and closed
with second pression of the button.
Utopia free-hands was designed to be installed in two different ways:
wall-mounted without the need for masonry work, or fl ush-mounted
to reduce the protrusion from the wall to only 16mm.
Utopia has two sets of auxiliary buttons in addition to colour,
brightness and contrast.
Three indicator LEDs are provided for more simple and immediate use.
These indicate open door, mute function and audio on conditions.
SPECIFICATIONS
The main characteristics of the video door phone are:
Flat 4” TFT backlit colour module.
Call speaker separate from handset.
Adjustable call volume: when the call volume selector is in “MUTE”
( ) position, the corresponding LED lights up to indicate that the
call tone has been inhibited. The LED is visible also when the front
panel is closed.
When volume is set to “MUTE” the video door phone will not ring
but the video module will light up.
Adjustable colour and brightness of the picture by means of a
slider.
Adjustable contrast by means of a trimmer positioned under the
sliding front panel.
Two additional buttons ( , ) for programming, auto power-on,
special decoder activation for secondary electrical locks, staircase
lights, etc.
Button : press this button to activate the “automatic door
opener” function. A door opener command will be sent when a
call is received from a door unit. The red LED indicates when the
function is on.
Door opener button: simply press the button to operate the door
lock ( ); the button will remain lit as long as the picture appears
on the video door phone.
Open door indicator: a red LED lights up when the door is open if
the system is set up for this function.
•
•
•
§
•
•
•
•
•
•
Ref. 1703/4
1
2
3
4
142 mm
10
9
11
7
6
5
8
49 mm
225 mm
1
Audio button
2
Auxiliary buttons
3
Brightness adjustment control
4
Colour adjustment trimmer
5
Button for automatic door opener function
6
Contrast adjustment control
7
Call tone adjustment trimmer
8
Door opener button
9
Audio on LED
10
Mute function led
11
Door open LED (red) and automatic door opening function on
LED (green)
TECHNICAL FEAUTURES
Power voltage: 16 ÷ 18,5Vcc
Working Uptake: max 0,36A
Stand-by: 0,1A
Working power: max 6,5W
CCIR Version Vertical frequency: 50Hz ± 2Hz
Horizontal frequency: 15625 ± 300Hz
Video signal: 1Vpp 75Ω nominal
1Vpp -6 dB minimum
LCD: 4” backlit
Screen size: 81 x 59mm
Resolution: 480H x 234V pixel
Colour system: PAL
Switch-on delay: 4 sec. max
Transmitting capsule: electret microphone
Receiving capsule: speaker 45Ω
Button voltage: 24Veff. max
Button current: 1,2 Aeff
Operating temperature range: -5° ÷ +45°C
Max. humidity: 90% UR
APARTMENT VIDEO DOOR PHONE STATIONS
18
−−−−
sec.4a
2GO! - Technical manual
BRACKET Ref. 1703/84
The Utopia video door phone Ref. 1703/4 is supplied without bracket
that must be purchased separately
The bracket fi ts connection terminals, programming dip switches and
line terminal switch.
A yellow LED is provided for checking correct reception of the video
signal. The LED comes on if reception is not optimal.
1 2 3 4 5
ON
1 2
ONDIP
32
1
4
5
1
Line terminal switch
2
Terminal board
3
User code dip switch (CODE)
4
Apartment internal code dip switch (INT)
5
Yellow indicator LED
BRACKET TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
CP
}
Floor call button
CP
To use the fl oor call or supplementary ringer function, remove the
dedicated terminal protection and connect the respective wires.
TECHNICAL FEAUTURES
Max. bracket draw with monitor on: 550mA
Max. bracket draw in standby: 11mA
DEFAULT PROGRAMMING
User code: 31
Indoor station code: 0
Line termination: ON
WALL-MOUNTED INSTALLATION
1. Arrange the duct so that it ends in correspondence with one of the
input holes.
2. Remove bracket protection.
NO
3. Arrange the bracket on wall considering height from ground and
side clearance.
155 cm
7 cm
6 cm
10 cm
10 cm
NO
4. Fasten the bracket to the wall using the bolt provided.
Alternatively fasten the bracket to a fl ush-mounting box using the
specifi c holes.
NO
NO
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
BRACKET Ref. 1703/84
WALL-MOUNTED INSTALLATION
APARTMENT VIDEO DOOR PHONE STATIONS
sec.4a
−−−−
19
2GO! - Technical manual
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
FLUSH-MOUNTED VERSION INSTALLATION
5. Arrange wiring and refi t the clip-on cover on the bracket. Remove
the cover only before fi tting the Utopia video door phone on the
bracket.
NO
6. Remove the protective cover from the bracket.
7. Fit the Utopia video door phone on the bracket as follows:
Fasten the video door phone to the hooks B on the upper side
of the bracket.
Turn the video door phone downwards.
Shut the video door phone on the bracket and ensure that
fastening lever C is blocked.
B
C
Press lever C and reverse the sequence to remove the video
door phone.
•
•
•
§
FLUSH-MOUNTED VERSION INSTALLATION
Fit the Ref. 1703/60 fl ush-mounting box at the recommended
height from the fl oor.
TOP
2 cm
165 cm
2 cm
Ref. 1703/60
Fit the frame inside the box and adjust correct perpendicularity.
TOP
TOP
C
•
•
APARTMENT VIDEO DOOR PHONE STATIONS
20
−−−−
sec.4a
2GO! - Technical manual
Remove bracket protection.
NO
Remove the three fastening teeth from the bracket.
NO
Fasten the bracket to the frame.
TOP
D
NO
•
•
•
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
UTOPIA FREE-HANDS COLOUR VIDEO DOOR PHONE Ref. 1703/4
FLUSH-MOUNTED VERSION INSTALLATION
Arrange wiring.
TOP
NO
Remove the sliding protective covers.
•
•
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

urmet domus MT124-017 Technical Manual

Brand
urmet domus
Model
MT124-017
Category
Door intercom systems
Type
Technical Manual

The urmet domus MT124-017 is a high-quality audio/video door entry system that allows you to see and speak to visitors at your door before granting them access. The system includes a sleek, modern design that will complement any home décor. With its built-in camera and microphone, you can easily identify visitors and communicate with them from the comfort of your own home. The system also features adjustable volume controls, so you can customize the sound level to your liking. Installation is simple and straightforward, and the system is compatible with most existing door entry systems.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents