BARRON AXL2 80-280W Series LED Flood Luminaire Installation guide

Brand
BARRON
Model
AXL2 80-280W Series LED Flood Luminaire
Category
Motorcycle Accessories
Type
Installation guide
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
When using electrical equipment, basic safety precautions should always be followed including the following:
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
• Installation and servicing of this equipment should be performed by qualified service personnel only.
• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations, if
applicable.
• Do not mount near gas or electrical heaters.
• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering
by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Any modification or use of non-original components will void the warranty and product liability.
• Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS!
Technical Support ■ (623) 580-8943 ■ [email protected]
AXL2 (80-280W)
Installation Instructions
20070138 REV 2 - 05/21 1 800-533-3948 www.barronltg.com
Fixture Preparation
Slip-Fitter (fits up to 2 3/8” OD)
1. Separate the slip-fitter from the knuckle by removing the adjustment bolt using a hex wrench (provided by others).
(Fig. 1)
2. Feed wire leads from the fixture through the knuckle and attached the knuckle to the head. (Fig. 2)
3. Feed wire leads through the slip-fitter and then attach the slip-fitter to the knuckle. (Fig. 3)
Trunnion
1. Feed wire leads through slot in trunnion. (Fig. 4)
2. Attach trunnion to the head. (Fig. 5)
Yoke
1. Attach yoke to the head using a hex wrench (provided by others). (Fig 6)
Fig. 1 Fig. 2 Fig. 3
Fig. 4 Fig. 5
Fig. 6
AXL2 (80-280W)
Installation Instructions
20070138 REV 2 - 05/21 2 800-533-3948 www.barronltg.com
Surface/Pole Mounting
Slip-Fitter (Fig. 7)
1. Make electrical connections; see
Electrical Connections
section.
2. Secure slip-fitter over pole and tighten.
3. To position the angle of the fixture, loosen the adjustment bolt using
a hex wrench (provided by others), position head as desired, then
retighten the bolt.
Note: Adjustable angle is 0-90°.
IMPORTANT: Weatherproof your outdoor installation. Be sure to seal
all holes in the enclosure, such as the mounting, conduit, plugs,
sensors, and photocontrols with silicone sealant.
Trunnion (Fig. 8)
1. Drill hole in mounting surface or rectangular pole.
2. Attach the fixture to mounting surface or rectangular pole.
3. Make electrical connections in waterproof J-box or inside pole; see
Electrical Connections
section.
IMPORTANT: Weatherproof your outdoor installation. Be sure to seal
all holes in the enclosure, such as the mounting, conduit, plugs,
sensors, and photocontrols with silicone sealant.
Yoke (Fig. 9)
1. Drill hole in mounting surface or rectangular pole.
2. Attach the fixture to mounting surface or rectangular pole.
3.
Make electrical connections in
waterproof J-box or inside pole
; see
Electrical Connections
section
.
IMPORTANT: Weatherproof your outdoor installation. Be sure to seal
all holes in the enclosure, such as the mounting, conduit, plugs,
sensors, and photocontrols with silicone sealant.
Adjustment Bolt
Pole (Round or Rectangular)
Slip Fitter
Fig. 7
Fig. 8
Mounting Surface
or Rectangular Pole
Mounting Surface
or Rectangular Pole
Fig. 9
Fig. 10 - Yoke Templates
3"
2.3"
1.2"
3.3" 0.5"
6-Φ0.5"
80-140W
3"
2.3"
1.2"
3.3" 0.5"
6-Φ0.5"
240-280W
Φ0.8"
Φ0.79"
AXL2 (80-280W)
Installation Instructions
20070138 REV 2 - 05/21 3 800-533-3948 www.barronltg.com
Surface/Pole Mounting, Continued
Arm (Fig. 11)
1. Disassemble the pole bracket from the arm.
2. If assembling to a round pole, remove and discard the adapter
gasket.
3. Using the pole bracket as a guide, drill holes in the pole at desired
location.
4. Attach the arm to the pole with the pole bracket inside the pole.
5. Feed wire leads from the fixture through the slot in the arm.
6. Attach the fixture head to the arm using the adjustment bolt.
7. Adjust the head to desired position and tighten the adjustment bolt.
8. Make electrical connections in the arm wiring compartment or inside the pole; see
Electrical Connections
section.
9. Secure the wiring cover to the arm with the gasket in between.
IMPORTANT: Weatherproof your outdoor installation. Be sure to seal all holes in the enclosure, such as the mounting,
conduit, plugs, sensors, and photocontrols with silicone sealant.
Electrical Connections (Fig. 12)
All electrical connections should be made inside the junction box. Make electrical connection as follows:
120-277VAC
Black - 120-277VAC
White - Common
Green/Yellow Green - Ground
Note: Cap unused leads to prevent
shorting.
Note: This fixture auto-adjusts for
voltages from 120-277VAC.
If dimming is used:
Purple - Positive (+)
Grey - Negative (-)
Fig. 12
Driver
Black - 120-277VAC
White - Common
Green/Yellow Green - Ground
Photocontrol
Motion Sensor
Driver
Red - 120-277VAC
White - Common
Green/Yellow Green - Ground
Black
Standard
With Photocontrol Motion Sensor
Fig. 11
Pole
Bracket
Adapter
Gasket
Adjustment Bolt
Wiring Cover
Arm
AXL2 (80-280W)
Installation Instructions
20070138 REV 2 - 05/21 4 800-533-3948 www.barronltg.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

BARRON AXL2 80-280W Series LED Flood Luminaire Installation guide

Brand
BARRON
Model
AXL2 80-280W Series LED Flood Luminaire
Category
Motorcycle Accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents