Andersen Sill Cover Replacement Service Instructions

  • Hello! I've reviewed the user guide for replacing sill covers on Andersen E-Series French Casement and Casement & Awning windows. This document provides step-by-step instructions and safety warnings for the replacement process. It includes details on required tools, and covers the process of removing the old sill cover and installing the new one. I'm ready to answer your questions about this procedure.
  • What tools are needed for the sill cover replacement?
    What should I do before starting the installation?
    What should I do with the old sill cover?
    Which windows does this guide refer to?
Use caution when working at elevated heights and around unit openings.
Follow manufacturers’ instructions for ladders and/or scaffolding. Failure
to do so may result in injury or death.
Sea cauteloso al trabajar en lugares elevados y cerca de las aberturas de
la unidad. Siga las instrucciones del fabricante para el uso de escaleras
y/o andamios. Si no lo hiciera, podrían producirse lesiones o la muerte.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage.
Siga las instrucciones del fabricante para el uso de herramientas
eléctricas o manuales. Utilice siempre gafas de seguridad. Si no lo
hiciera, podrían producirse lesiones y/o daños al producto.
9069249 BA Revised 06/20/13
Tools Needed Herramientas necesarias
Safety Glasses Lentes de seguridad
Flat Blade Pry Bar Flat Blade Pry Bar
Flat Blade Screwdriver Flat Blade Screwdriver
Drill/Driver Drill/Driver
#2 Phillips Bit #2 Phillips Bit
5/32" Hex Key (for French Casement only)
Sill Cover Replacement
for E-Series French Casement and Casement & Awning Windows with Standard or Piano Hinge
for E-Series/Eagle® French Casement and Casement & Awning Windows with Standard and Piano Hinge
Parts Included Partes incluidas
(1) Sill Cover Sill Cover
Sill Cover
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.
Please leave this guide with building owner.
Si tiene alguna pregunta llame al 1-888-888-7020. Para obtener más información y/o guías, visite www.eaglewindow.com
Deje esta guía con el dueño de la construcción.
Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Lea completamente la guía antes de comenzar la instalación. Lea y respete todas las advertencias y precauciones durante la instalación de la unidad.
Check with your local building code ofcial to identify and conrm compliance with local building code requirements.
Consulte los códigos locales de construcción para identicar y conrmar que se cumplan los requisitos del código de construcción.
Standard casement window shown in guide.
Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved.
2
9069249
Loosen set screw on handle using a small at blade screwdriver.
Loosen set screw on handle using a small at blade screwdriver.
Remove screws from sill cover and save for reuse.
Remove screws from sill cover using a drill/driver and save for reuse.
Remove handle and save for reuse. Remove operator cover and save for
reuse.
Remove handle and save for reuse.
Remove sill cover and dispose of properly.
Drill/Driver
Flat Blade Pry Bar
Sill Cover
Sill Cover
1
Interior
Handle
Flat Blade Screw-
driver
Set Screw
Operator Cover
Operator
2
Interior
5
Interior
6
Interior
Using a 5/32" hex key, remove screws on the back side of the sill
cover and save for reuse.
3
Exterior
5/32" Hex
Key
Sill Cover
Screws
Pull lock handle through the face of sill cover and save for reuse.
Pull lock handle through the face of sill cover and properly dispose.
4
Interior
Sill Cover
Lock Handle
For French Casement Windows proceed to step 3.
For other casement and awning windows proceed to step 5.
French Casement Only
3
9069249
Slide new sill cover into place over operator and between side stops.
Slide new sill cover into place over operator and between side stops.
Fasten sill cover using saved screws.
Tighten handle set screw.
Tighten handle set screw.
Sill cover replacement is complete.
Sill cover replacement is completed.
Reapply operator cover. Reapply handle.
Reapply operator cover.
Operator Cover
Operator
Handle
Flat Blade
Screwdriver
Set Screw
12
Interior
11
Interior
Insert saved lock handle into sill cover in same position.
Insert new lock handle into sill cover in same position and secure using
saved screws.
9
Interior
10
Exterior
Secure lock handle using saved screws.
Insert new lock handle into sill cover in same position and secure us-
ing saved screws.
New Sill Cover
7
Interior
Drill/Driver
Sill Cover
8
Interior
For French Casement Windows proceed to step 9.
For other casement and awning windows proceed to step 11.
French Casement Only
5/32" Hex
Key
Sill Cover
Screws
/