UPLIFT Desk FRM582 Operating instructions

Brand: UPLIFT Desk

Model: FRM582

Type: Operating instructions

UPLIFT Desk FRM582 is a height-adjustable standing desk designed to provide ergonomic comfort and improved productivity. With a sturdy 4-leg frame and leveling glides, it ensures stability on various surfaces. The desk allows you to effortlessly adjust the height using the included 4mm Allen Wrench, offering a wide range of positions to suit your needs. It comes with pre-installed leveling glides for precise leveling and casters for easy mobility. The FRM582 is equipped with safety features such as obstacle detection to prevent collisions and a reset procedure for optimal performance.

Package Contents

V2 4-Leg Foot

(qty 2)

4mm Allen WrenchM6x12 Machine Screws

(qty 16)

V2 4-Leg Standing Desk

Foot Replacement Instructions

FRM582

Step 1

A. Remove all objects, accessories, and attached

components from desk since you will be inverting

it for this installation.

B. Press and hold the Down Button to bring the desk

to its lowest position, then unplug the desk from

the electrical outlet.

C. Priortoippingthedeskover,moveittoasuitable

area free from clutter or obstruction. We recom-

mend resting the desktop on a carpet or blanket.

Be aware of any cables or attached components

andsecurethembeforeippingthedesk.

• Note: When ipping the desk, always hold the

frame and the desktop together. Lifting by the

desktop only could put stress on improperly

fastened screws connecting the desktop to the

frame and may cause them to separate from the

frame if they were not attached properly.

D. You and a friend should each hold on to the rear

edge of the desktop with one hand and hold a leg

with the other hand.

E. Supporting both the desk frame and the desktop,

slowly tilt the desktop toward the rear of the desk

until the back edge of the desktop is resting on the

ground.

F. Hold onto the leg and the front edge of the desk-

top, then tilt the desk another 90 degrees until the

desk is upside down and resting on a carpet or

blanket.

Recommended Assembly Workspace & Practices

• Place all parts on a clean surface such as a rug or carpet to avoid scratches.

• Two or more people are recommended for assembly.

• Remove all packaging materials before beginning the assembly process.

Step 2

A. If your desk has casters installed and you plan to

use them with the new Feet, remove them from

each of the currently installed peg feet. You may

needa0.5”(13mm)atwrenchorthinadjustable

crescent wrench to remove the casters.

B. Using the included 4mm Allen Wrench, remove

each of the M6x14 Machine Screws that are hold-

ing the peg feet to the legs (four screws per peg

foot).

A. B.

Step 4

A. If you are replacing casters removed in Step 2,

rst remove the pre-installed leveling glides by

unscrewing them, no tool necessary.

B. Thread the casters into the Feet and use a 0.5”

(12mm)atwrenchtotighteneachcaster.

C. Ensure the casters are in the locked position be-

foreippingyourdeskuprightagaintoensurethe

deskdoesnotmoveasyouipitontothecast-

ers.Tolockthecasters,iptheleverattheback

of each caster to the down position (towards the

ceiling when the desk is upside down) and test the

wheel to make sure it does not turn.

Step 3

A. Place one of the new Feet on top of two legs on

one side of the desk, as shown, with the pre-in-

stalled leveling glides facing up.

B. Insert, but do not tighten, a M6x14mm Machine

Screw into each of the eight threaded holes.

• Note:Ifyouarehavingdifcultyaligningthe

holes in the Foot with the holes in the legs, use

the 4mm Allen Wrench to loosen, WITHOUT

REMOVING, the four screws that attach each

leg to the crossbar ends. Be sure to rmly

tighten these screws again once the Foot has

been fastened to the legs.

C. Once all eight screws have been started, tighten

them with the 4mm Allen Wrench.

D. Repeat the previous steps for the second new

Foot.

E. The desk frame screws can become loose over

time or may not have been completely tightened

during the initial assembly. Since the desk is upside

down, take the opportunity to ensure all frame

screws are tight using the 4mm Allen Wrench.

Step 5

A. Withthehelpofafriend,ipthedeskupright.Re-

fer to Step 1 and reverse those instructions.

B. Move the desk back to its location.

• If you have casters installed, make sure the

casters are not locked and roll it to the loca-

tion.

• If you are using the pre-installed leveling

glides, carefully lift the desk with two or more

people and move it to its location - DO NOT

drag the desk as this may cause damage to

thedeskandoor.

C. Once the desk is in position, reinstall any accesso-

ries that had been removed and plug the power

cord back into the outlet.

D. Before use, perform the reset procedure below.

This is an important step.

Reset Procedure

Before using the desk, you must rst perform this

Reset Procedure:

• Press and hold the Down Button until the desk

stops at its lowest position, then release.

Note: On the Advance Paddle keypad, press

down on the paddle.

• Press and hold the down button again for 30

seconds, then release.

Note: On the Advance Paddle keypad, the

word “RESET” will appear at this point.

Note: On other UPLIFT keypads with display,

the letters “ASr” will appear at this point.

• Press and hold the Down Button one more time

until the desk lowers slightly, rises and stops,

then release the button. The reset is complete

and the desk is ready for use.

RESET

Copyright Notice: These instructions are a component of this product. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website: uplift-

desk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.

CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may

result in damage or personal injury. Retain manual for future reference.

WARNING:Designedforuseindryworkenvironmentsonly.Riskofre,electricshock,orper-

sonal injury if used outdoors or in a damp location. Use only indoors.

WARNING: Make sure that the wires for your monitor and devices are not touching any obsta-

cles or walls and are an appropriate length to allow for full adjustment of the desk. Make sure

that no obstacles are in the full range of height adjustment.

WARNING:

Only plug the desk into a properly grounded 120V outlet. Unplug the desk from the

electrical outlet before moving the desk or before adding/removing parts or accessories. Risk of

electric shock.

WARNING: Do not open any desk component or insert any object in a desk component. Risk of

electric shock.

WARNING: In case of spilled liquids, immediately unplug desk. Then clean spill with a dry cloth.

Risk of desk failure or electric shock if desk components become wet.

WARNING: Keep heated surfaces away from plug. Never use the desk with a damaged cord or

plug. Risk of electric shock. Call us for a free replacement cord.

WARNING:Keepngersandallbodypartsclearofthemovingdesk.Checksurroundingsonall

sides before using the desk to ensure there are no immobile obstacles within the desk’s range of

motion. Ensure all cords are the appropriate length so they don’t pull as the desk moves.

WARNING: Keep unsupervised children away from the desk. Before use, teach children about

desk safety with this manual. Risk of personal injury and electric shock if the desk is misused.

WARNING: This desk is height adjustable so that it may be positioned at a user’s ergonomic

height as described in this manual. Inappropriate use of this desk can cause property damage or

bodily injury. Under no circumstances does the manufacturer accept warranty or liability claims

for damages caused from improper use or handling of this desk. Provide this manual to any new

user.

WARNING: When relocating the unit, remove all devices to avoid harm or damage, and adjust

the unit to its lowest position.

WARNING: When relocating the unit, move it carefully with two people, to avoid injury and

damage to the product and surroundings.

CAUTIONS & WARNINGS

AI-FRM582-1.0

UPLIFT Desk FRM582 Operating instructions

Brand: UPLIFT Desk

Model: FRM582

Type: Operating instructions

Download PDF

report

UPLIFT Desk FRM582 Operating instructions

UPLIFT Desk FRM582 Operating instructions

Related papers

Other documents