UPLIFT Desk - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30") Installation guide

Brand: UPLIFT Desk

Model: - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30")

Type: Installation guide

This manual is also suitable for

- 2-Leg Seated Height Side Table Frame (White)

UPLIFT Desk - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30") is a high-quality and versatile piece of furniture that can be used in a variety of settings.

With its sturdy construction and durable materials, this side table is built to last. The whiteboard desktop provides a convenient and easy-to-clean surface for writing and drawing, making it perfect for brainstorming sessions, presentations, or simply jotting down notes.

The grommets on the desktop allow you to easily manage cords and cables, keeping your workspace neat and organized. The table's compact size makes it ideal for use in small spaces, and the adjustable height allows you to customize it to your needs.

UPLIFT Desk - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30") is a high-quality and versatile piece of furniture that can be used in a variety of settings.

DIRECTIONS FOR ASSEMBLY AND USE

2-Leg Side Table

SAVE THESE INSTRUCTIONS:

Any user or installer of the table must study this manual carefully. If this table is sold,

please provide the manual to the buyer, installers, or support personnel using the product.

TABLE OF CONTENTS PAGE

1 Safety and Warnings 2

2 Usage 2

3 Parts List 2

4 Assembly Instructions 4

5 Placement 5

6 TechnicalSpecications 5

FRM220/R01

4933053179446 - THS610

This table is designed for use in dry work areas only. These tables are designed only for the purposes

included in this manual. They should not be used in environments with high humidity or dampness.

Any other use is at user’s risk.

Do not sit or stand on the table frame.

Children should never use the table unless they are supervised by adults.

Liability: Under no circumstances does the manufacturer accept warranty claims or liability claims for

damages caused from improper use or handling of the table frame other than that which is described

in this operation manual.

Read all instructions before using the table.

FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY, AND OPERATION INSTRUCTIONS

AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY

DAMAGE OR BODILY INJURY.

WARNING - To reduce the risk of injury to persons, or property damage:

• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled

persons.

• Use this table only for its intended use as described in these instructions. Do not use attachments

not recommended by the manufacturer.

• Do not use outdoors.

• Inappropriate use of this product may cause property or bodily injury.

• Please provide this manual to any users, installers, or support personnel using the product.

•

If casters are not installed, use a two-person lift and lift the table so that it can be moved without

dragging. Dragging the table may cause the frame and screws to pull loose from the desktop.

•

Maximum weight capacity of this product is 355 Ib. Do not overload your table.

2. USAGE

1. SAFETY AND WARNINGS

Foot

(qty 2)

Leg

(qty 2)

Adhesive pads

(qty 10)

Leveling stud

(pre-installed, qty 4)

M6x10

Machine screw

(qty 8)

#10x5/8’’

Wood screw

(qty 12)

#10-24x5/8’’

Machine screw

(qty 8)

Crossbar end

(qty 2)

Crossbar rail

(qty 2)

Side bracket

(qty 2)

M6x14

Machine screw

(qty 24)

Philips Head Screwdriver

and/or Power Drill

Tape Measure

Allen wrench

(included)

Tools requiredComponents

10 10

a b

3. PARTS LIST

Part Description Qty

Leg 2

Foot 2

Crossbar end 2

Crossbar rail 2

Side bracket 2

Adhesive pads 10

Leveling studs

(pre-installed in feet) 4

M6x14 Machine screw 24

M6x10 Machine screw 8

#10x5/8’’ Wood screw (not pictured) 12

#10-24x5/8’’ Machine screw (not pictured) 8

Please count all pieces before disposing of any carton or packing material. Use a padded or carpeted

area for assembly to avoid damage. For ease and safety, we recommend two people for assembly.

Conguration

B. Position the Crossbar ends (part 3) on their sides. You will be inserting

the Legs (part 1) into the Crossbar ends from below. When positioned correctly,

themounttabswillbefacingup(g.1).

Now, place the Legs (part 1) into the Crossbar ends from the

bottom(g.2).UsingthesuppliedAllenwrench,insertfour

(4) M6x14 Machine screws (part 8) into the Crossbar ends,

and rotate each screw only a few turns. Do not tighten fully

until step D.

If you drop a screw inside the Crossbar end, simply tilt

to retrieve the screw.

A. FullyseparatetheCrossbarends(part3)youwillndtheCrossbarrails(parts4)inside.

g.1

g.2

3 3

4. ASSEMBLY INSTRUCTIONS

C. Take the two Side brackets (part 5) and attach them to the Leg

assemblies, using four (4) M6x14 Machine screws (part 8) each. Use

the Allen wrench, and rotate each screw only a few turns. Do not

tighten fully until step D.

If you are having trouble getting all the screws started, it is because

other screws are too tight. You’ll need to back out some screws in

order to loosen the tolerance of the screw holes.

D. Once all of the parts are connected, you can now tighten the eight (8) Screws from Step B and the

eight (8) Screws from Step C (16 screws in total).

Remove backing from the Adhesive pads (part 6) and position

along the assembly as shown. Be sure to not cover any of the holes.

F. Slide Crossbar rails (part 4) back into Crossbar ends (part 3).

Ensure the slots of the Crossbar rails are facing inward. The slot on

theCrossbarrailisoffset;itwillneedtobealignedinaspecicway

totaroundtheMachinescrews.MakesurethattheCrossbarrail

(part 4) can slide all the way to the end of the Crossbar end (part 3).

Ifitdoesn’tt,taketheCrossbarrailoutandipitover,withtheslots

facinginwardandnearthetopoftheedge,furtherfromtheoor.

G. Attach each Foot (part 2) with four (4)

M6x14 Machine screws (part 8) and tighten

bolts in a cross pattern.

Be sure to point the long end of the Foot in

the same direction as the long end of the Side

bracket.

H. Your desktop may be pre-drilled or include threaded inserts.

Please check both sides of the desktop for holes before placing

the table frame! If there are holes, carefully line up the frame to

match the holes on the underside of the desktop.

Adjustthewidthofthebasetotthedesktopbyslidingthetwo

halves outward. (33’’ max between the inside edge of Crossbar

ends)

If your desktop is not pre-drilled & does not include threaded in-

serts, place the base where you want it. We recommend leaving at

least 1/2” of desktop width on either side of the Side brackets.

The table feet are deeper than the Side brackets. If your top is

25.5”-27.5” deep and you want the rear edge of the top in line with

the rear edges of the feet, offset your desktop toward the back.

If you are using your own desktop, please note that the Minimum desktop size is 43’’ wide x 24’’ deep.

Theframewillnottonanydesktopsmallerthanthis.

I. Secure the Center rails at both ends using

eight (8) M6x10 Machine screws (part 9), four

(4) per side. Ensure all eight (8) Machine screws

hit the metal Crossbar rails to prevent them

from sliding.

Double-check that the frame is properly positioned

on the underside of the desktop.

Attach the frame assembly to the underside of the

desktop using eight (8) of the screws that you have chosen.

J. Choose the screw to fasten your frame to your desktop.

If your desktop does not have metal threaded inserts,

use the #10x5/8’’ Wood screws (part 10-a)

If your desktop does have metal threaded inserts,

use the #10-24x5/8’’ Machine screws (part 10-b)

3 per Side bracket 6 total

1 per Crossbar end 2 total

N. Turn the assembled table right-side up. With two people, grab the table by the frame and desktop

equally, and turn the table right-side up. Adjust the Leveling studs (part 9) on the Feet (part 2) as needed.

This guide is a component of the UPLIFT Desk

™

. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT

Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.

These instructions are subject to United States copyright law.

Following table assembly, adjust the Leveling studs or casters (sold separately) on the feet so that the

table is level and does not shift its position.

When moving the table, if casters are not installed, use a two-person lift and lift the table so that it can be

moved without dragging. Dragging the table may cause the frame and screws to pull loose from the desktop.

When moving the table, DO NOT lift the table by the desktop alone, or the frame, alone. Support both the

frame and the desktop equally. Favoring one over the other can stress the fasteners connecting the table

frame to the desktop. Lower the table completely and lift the table by grasping the frame.

5. PLACEMENT

Height 28” (without desktop)

Width Range 42.125” min - 74.75” max

Weight Capacity 355 lbs

6. TECHNICAL SPECIFICATIONS

Notes

1-800-349-3839

[email protected]

www.upliftdesk.com

UPLIFT Desk - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30") Installation guide

Brand: UPLIFT Desk

Model: - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30")

Type: Installation guide

This manual is also suitable for

- 2-Leg Seated Height Side Table Frame (White)

UPLIFT Desk - Whiteboard Desktop, Seated Height Side Table (White) Grommets (White) (48" x 30") is a high-quality and versatile piece of furniture that can be used in a variety of settings.

Download PDF

report