UPLIFT Desk STR034 User manual

Brand: UPLIFT Desk

Model: STR034

Type: User manual

UPLIFT Desk STR034, a sturdy and versatile base, is compatible with both the MoPac Cabinet and the MoPac Wardrobe. It allows you to create a customized storage solution that meets your specific needs, whether for office or home use. The base features a solid construction with steel legs and crossbars, ensuring durability and stability. The adjustable leveling glides enable you to level the unit on uneven surfaces, providing a secure and balanced foundation for your cabinet or wardrobe.

MoPac Base

STR034

Thank you for choosing UPLIFT Desk.

Safety and Warnings

WARNING! Read all instructions before assembly. Failure to assemble or operate properly may result in

damage or personal injury. Retain this manual for future reference.

WARNING! To prevent tipping, store the heaviest items towards the bottom.

WARNING! Do not stack more than four MoPac Cabinet units vertically or one MoPac Cabinet on one

MoPac Wardrobe.

WARNING! Ensure the furniture is unloaded of contents before moving.

WARNING! Keep all hardware and parts out of reach of children.

WARNING! Do not climb on or allow children to climb on this furniture.

WARNING! If stacking cabinets or stacking a single cabinet on a wardrobe, use the MoPac Security

Straps to prevent stacked cabinets from tipping and causing damage, injury, or death. See installation

instructions for the security straps included with each MoPac Cabinet and MoPac Wardrobe.

Legs

(qty 2 )

M6x20 Flat head Screws

(qty 4)

Attachment Plate

(qty 2)

Crossbar

(qty 2)

PACKAGE CONTENTS

M6x12 Pan head Screws

(qty 4)

4mm Allen Wrench

MoPac Stacking Brackets

The MoPac Base is compatible with both the MoPac Cabinet and the MoPac Wardrobe. The illustra-

tions used in these instructions show the attachment of the Base to the MoPac Cabinet, but the steps

for attaching the Base to the MoPac Wardrobe are identical.

M6 Washers

(qty 4)

ASSEMBLY INSTRUCTIONS

Step 1

A. Place all parts on a clean and smooth surface such as a rug or carpet to avoid scratches.

Remove all packaging materials, including box straps, before beginning the assembly process.

With assistance, turn the cabinet or the wardrobe on its back on a at, clean surface such as a carpet or

blanket.

Remove leveling glides from the bottom if they had been previously installed.

Step 2

A. Align one of the Attachment Plates with the left or right edge of the cabinet or wardrobe in the orienta-

tion shown.

Insert two of the M6x20 Flat head Screws through the Attachment Plate where shown and into the thread-

ed inserts along the bottom panel of the cabinet or wardrobe.

Once both screws are started, tighten them with the 4mm Allen Wrench. Be careful not to overtighten the

screws to avoid stripping out the threaded inserts.

Repeat Step 2 with the other Attachment Plate.

DETAIL B

SCALE 1 : 2

DETAIL B

SCALE 1 : 2

Step 3

A. Take the Crossbars and slide them over the tube extensions on the side of one of the Legs. Ensure the

parts are oriented as shown so that the large hole found along the side of each Crossbar aligns with the

threaded holes in the Legs.

Slide the tube extensions of the other Leg into the opposite ends of the Crossbars.

Slide the assembly of the Crossbars and Legs over the Attachment Plates as shown so that the tabs on the

Attachment Plates are located inside of the Crossbars and Legs assembly.

DETAIL C

SCALE 1 : 2

Ensure holes on the Crossbar

align with the holes on the Legs.

Step 4

A. With assistance, return the cabinet or wardrobe to an upright position and place it in its nal location. Be

careful to lift the unit to move it. Do NOT drag the unit along the oor as doing so may damage the unit

and/or your oor.

Rotate the leveling glides to level the cabinet or wardrobe if the oor is uneven.

DETAIL D

SCALE 1 : 1

DETAIL D

SCALE 1 : 1

Step 3 Continued

D. With the four M6 Washers,

loosely insert the M6x12 Pan head Screws through the holes in the Attachment

Plate tabs and Crossbars and into the threaded holes in the Legs.

Once all four screws are started, tighten them using the provided Allen Wrench.

DETAIL C

SCALE 1 : 2

DETAIL C

SCALE 1 : 2

800-349-3839

512-614-3152

[email protected]

upliftdesk.com

Work Better. Live Healthier

Copyright Notice: This guide is a component of the UPLIFT Desk™. This guide is a part of the scope of delivery, even if the item is resold. This guide

is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published

form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.

SAVE THESE INSTRUCTIONS

Study this manual carefully. If this desk is sold, please provide this

manual to the buyer, installers, or support personnel operating the product.

AI-STR034-1.0