2. Home
  3. Home security & automation
  4. Motion detectors
  5. Poewit
  6. OD-2 Cloud Intelligent Outdoor Architectural LED Lights
OD-2 Cloud Intelligent Outdoor Architectural LED Lights

Poewit OD-2 Cloud Intelligent Outdoor Architectural LED Lights User guide

  • Hello! I've reviewed the quick start guide for the PoEWit LED Flood Light models OD-2 and OD-2-PT. This document provides instructions on installation, highlighting the importance of protecting the PoE driver from moisture. It also mentions settings and how to control the lights and features such as PoE power supply, water-resistant housing, and the ability to control via an app and accessories. I'm ready to answer any questions you have about these devices.
  • Is the PoE LED driver water resistant?
    What type of wire is recommended for extending the connection between the driver and the light?
    What is needed for automatic internet connection?
    Can the lights be controlled if internet goes down?
poewit.com
CLOUD INTELLIGENT
OUTDOOR ARCHITECTURAL LED LIGHTS
POWERED BY PoE
QUICK START GUIDE
OD-2 MODEL
poewit.com
INSTALLATION AND SETUP
2
WARNING - BEFORE INSTALLATION
POEWIT POE POWERED ARCHITECTURAL LIGHTS CAN BE MOUNTED
OUTDOORS, ON A WALL OR CEILING. THE LIGHT HOUSING IS
WATER-RESISTANT; HOWEVER, THE ACCOMPANYING POE LED
DRIVER IS NOT WATER-RESISTANT.
THIS POE LED DRIVER IS DESIGNED TO BE SECURELY MOUNTED
IN A LOCATION FREE OF MOISTURE, SUCH AS INSIDE THE CAVITY
OF THE WALL.
IN CERTAIN INSTALLATIONS, THE INSTALLER MAY EXTEND THE
TWO CONDUCTOR WIRES (+ AND -) CONNECTING THE POE
DRIVER TO THE LIGHT FIXTURE. WE RECOMMEND USING AT
LEAST AN 20AWG WIRE AND 25 FEET OR LESS TO PREVENT
VOLTAGE DROPS.
Outside Wall
Inside Wall
poewit.com
INSTALLATION AND SETUP
3
BEFORE YOU START
1) PACKAGE CONTENTS
Confirm that you have the package contents as follows:
1. OD-2 PoE Powered LED Flood Light
or
2. OD-2-PT PoE powered LED flood light with PoE pass-through
3. Hardware screw bag
4. Quick start guide
OS-458/A
PA SS IVE INF RA -RED
SE NS OR
FO R AU TO MA TION
CO NT RO L
PACKAGE
CONTENT
ITEM
QUANTITY
OD-2 or
OD-2-PT
1
PoE Driver
1
Poe Powered
Architectural Lights
Quick start
1
or
poewit.com
INSTALLATION AND SETUP
4
2) INSTALLATION AND SETUP
1. Select a proper location for light xture and other connected devices.
2. Install Category Cable (CAT5e/6/7) from your PoE-enabled router
or broadband modem to the location selected for light installation.
3. Loosen the four screws holding the light housing back
mounting plate See figure 1
4. Insert category cable into PoE light driver and pull the light
driver cable through the back mounting plate opening. Mount
the back mounting plate to the wall with the four screws.
See figure 2
Fig 1.
poewit.com
INSTALLATION AND SETUP
5
5. Connect the light housing to the PoE driver wire. See figure 3
Fig 2
Fig 3
poewit.com
INSTALLATION AND SETUP
6
6. Push the cable assembly into the wall cavity and secure the
water tight grommet onto the back mounting plate. See gure 4
Fig 4
poewit.com
INSTALLATION AND SETUP
7
7. Attach the Light Housing to the Back Mounting Plate and tighten
the four screws. See gure 5
Fig 5
poewit.com
INSTALLATION AND SETUP
8
3) CONFIGURATION INSTRUCTIONS
Power up device; you should be automatically connected to the
internet. You are now ready to download and install your app.
You can search PoEWit in the apple app store or Google Play
to get the app
Note: Your device and mobile phone both must have an internet
connection through the same external IP address and must
be on the same local subnet.
After initial conguration, a PoEWit wall switch and/or PoEWit
motion detector PIR can control the lights should the internet
connection go down.
/