2. Home
  3. Home security & automation
  4. Motion detectors
  5. Poewit
  6. MD-2

Poewit MD-2 User guide

  • Hello! I've read the Quick Start Guide for the PoEWit Motion & Light Sensor MD-2. This document provides instructions for installing and configuring the device, as well as highlighting its app-controlled features and adjustable lens shields. The sensor uses Passive Infrared Motion Detection and is designed to automatically trigger lights. Feel free to ask me any questions about the device, its installation, or its functionality.
  • What is the detection range of the sensor?
    What should I avoid when installing the sensor?
    How do I adjust the detection area?
poewit.com
INSTALLATION AND SETUP
1
poewit.com
CLOUD-INTELLIGENT
POWERED BY PoE+
INDOOR DUAL
MOTION & LIGHT
SENSOR
QUICK START GUIDE
MD-2
poewit.com
INSTALLATION AND SETUP
1
1) PACKAGE CONTENT
2) PRODUCT DESCRIPTION
2.1 Features
This flush-mountable Passive Infrared Motion Detector is ideal for
an indoor installation. It will trigger lights to automatically power
on when an occupant enters its monitored space and power off
when the space becomes vacant. App-controlled Lux, Time, and
Duration-adjusting functions allow the user to conveniently control
conditions of motion detection.
2.2 Dimensions (See Fig 1-A and Fig 1-B)
OS-458/A
PA SS IVE INF RA -RED
SE NS OR
FO R AU TO MA TION
CO NT RO L
PACKAGE
CONTENT
ITEM
QUANTITY
PoE Motion/
Light Sensor
1
Lens Shield
2
Poe Powered
Architectural Lights
Quick Start Guide
1
poewit.com
INSTALLATION AND SETUP
2
3) INSTALLATION & WIRING
3.1 Select a Proper Location
Unit can be installed at a height of 2-4m (6.56 - 13.12ft). At a
height of 2.5m (8.02ft), the detection range can reach up to 8m
(26.24ft) in diameter with a 360-degree detection angle.
3.2 Installation Procedure
a. Drill a hole with a diameter of 65mm (2.55”) on the ceiling sheet .
rock. (See Fig 2)
b. Connect a Cat Cable to the MD-2 PoE Driver
75mm - 2.95”
Fig 1-A
59.46mm - 2.34”
56.7mm - 2.23”
Fig 1-B
poewit.com
INSTALLATION AND SETUP
3
c. Insert the MD-2 PoE Driver into the drilled hole cavity
d. Close two spring clips of detector and insert detector into the .....
drilled hole
�� =65
Ø
Drill a hole with a =65mm
on the ceiling
Ø
65mm - 2.55”
Fig 2
Spring clips
Ceiling board
poewit.com
INSTALLATION AND SETUP
4
2.5m
o
360
8m
3m
4m
Seated
Walk towards
Walk across
3.5m
H
3m
3m
3m
2m
N/a
Fig 3
Height Walk Across Walk Towards Seated
3.0m
2.5m
2.0m
4.0 m
6.56ft 22.96ft 9.84ft 9.84ft
9.84ft 29.52ft 13.12ft 19.84ft
8.20ft 26.24ft 13.12ft 9.84ft
11.48ft 32.80ft 13.12ft 6.56ft
13.12ft 13.12ft 13.12ft
8m
10m
9m
8m
7m
4m
4m
3m
4m
4m
8.20ft
9.84ft
13.12ft
26.24ft
poewit.com
INSTALLATION AND SETUP
5
Note: The unit is more sensitive to movement across than to
movement towards the detector. Detection coverage is reduced
when walking directly towards the unit. (See Fig 3 & 4)
3.3 Helpful Tips for Installation
WARNING: The detector will respond to temperature changes.
- Avoid pointing the detector towards highly-reflective surfaces
(such as mirrors, glass, etc.)
- Avoid mounting the detector near heat sources (such as heating
vents, air conditioners, lights, etc.)
- Avoid aiming the detector towards objects which may sway in the
wind (such as curtains, tall plants, etc.) (See Fig 5-A & 5-B)
Fig 4
poewit.com
INSTALLATION AND SETUP
6
4) SHIELD
4.1 Usage of Lens Shield
The MD-2 has two (2) lens shields for masking the undesired
detection area. (See Fig 6)
W
Fig 5-A Fig 5-B
Used Lens Shield Covered Detection Range
None
Small Segment
A+B+C
A+B
A
8m
1m
3m
5m
30º per piece
26.24ft
3.28ft
9.84ft
16.40ft
poewit.com
INSTALLATION AND SETUP
7
The shadow of the lens shield in Fig 6 represents the area excluded
from detection.
Φ8m
30 o
0
Φ5m
Φ3m
Φ1m
Part of the lens shield is used.
o
3
A
B
C
Fig 6
1m = 3.28ft | 3m = 9.84ft | 5m = 16.40ft | 8m = 26.24ft
poewit.com
INSTALLATION AND SETUP
8
After selecting the desired detection area, the redundant lens shield
should be illuminated. Fixing lens shield: There is slot around the
lens; insert the lens shield into slot. (See Fig 7)
5) CONFIGURATION INSTRUCTIONS
Power on the device. You should automatically be connected to the
Internet. You are now ready to download and install the PoEWit app.
Seach “PoEWit” in the Apple App Store or Google Play.
NOTE: Your device and mobile phone must both have an Internet
connection through the same external IP address and must be on
the same local subnet.
Fig 7
poewit.com
INSTALLATION AND SETUP
9
After initial configuration, a PoEWit wall switch and/or PoEWit
motion detector PIR can control the lights should the Internet
connection go down.
6) TROUBLESHOOTING
When the MD-2 works abnormally, check the “problems and
suggested solutions” table below.
Problem Possible Cause Suggested Solution
Nuisance
triggered
There are heat
sources, high-
ly-reflective
objects, or other
objects which
may sway in the
wind within the
detection cover-
age range.
Avoid aiming the detector towards
any heat sources, such as air condi-
tioning units, electric fans, heaters,
or any highly-reflective surfaces.
Verify that there are no swaying ob-
jects within the detection coverage
range.
/