VIA Technologies AMOS-5110 Quick Manual

Brand: VIA Technologies

Model: AMOS-5110

Type: Quick Manual

VIA Technologies AMOS-5110 is a rugged chassis kit, specially designed for VIA EITX-3000 Em-ITX board stacked with EMIO-3110 Em-IO module. It is a fanless, robust casting construction with high and scalable performance and low power consumption. It is easy to use, interchangeable and customizable with built-in common I/O functional cutouts for easy external access. It is compatible with VIA EITX-3000 embedded board and EMIO-3110 module. It supports 1 x 2.5” SATA hard disk drive bay and 1 x CompactFlash type I/II socket.

Note:

Please ensure that all items in the packing list are present

before using this product. If any of the items are missing or

damaged, contact your distributor or sales representative

immediately.

Packing List:

• 1 x Front I/O plate (P/N: 99G42-091636-A1)

• 1 x Rear I/O plate (P/N: 99G42-091646-A1)

• 1 x Storage metal top cover (P/N: 99G42-091656-A1)

• 1 x Storage bottom case (P/N: 99G42-092076-A1)

• 1 x CompactFlash cover (P/N: 99G42-090886-A0)

• 1 x Antenna cover (P/N: 99G43-120011)

• 1 x GPIO cable kit (P/N: 99G33-080185)

- 1 x GPIO cable port

- 2 x 6mm hex standoff screw

• 1 x SATA HDD (data and power) cable (P/N: 99G33-02093F)

• 1 x Screw pack (P/N: 99G44-030231)

- 23 x M3*5mm screw

• 1 x Screw pack (P/N: 99G44-010415)

- 10 x M3*6mm screw

• 1 x Hex screw package (P/N: 99G44-030221)

- 16 x 6mm hex standoff screw

• 1 x Quick guide (P/N: 99G51-013014-10)

AMOS-5110

Key Features:

•

Fanless, and robust casting construction

•

High and scalable performance with low

power consumption

•

Quick installation and easy maintenance

•

Easy to use, interchangeable and

customizable front and rear panels

•

Built-in common I/O functional cutouts

for an easy external access

The VIA AMOS-5110 is a rugged chassis kit, specially designed for VIA

EITX-3000 Em-ITX board stacked with EMIO-3110 Em-IO module. The

chassis kit offers fast and easy assembly. It consists of four parts: front

and rear I/O access plates, storage bottom chassis and the top cover.

The modularity of AMOS-5110 chassis kit combines with heatsink found

on the EITX-3000 board forming a solid and robust system chassis . It

gives developers a wealth of advantages including rich and versatile I/O

configurations through its expansive dual I/O coastline.

A system with the combination of AMOS-5110 chassis kit, EITX-3000

board and EMIO-3110 module can support up to six displays (four of

which can display completely different content). The combination is

ideally suited for display streaming media/advertisement in schools,

hospitals, corporations, airports, museums, retailers and train stations.

P/N: 99G51-013014-10

Quick Guide

Specifications:

• Chassis Construction:

▪ Front and rear I/O metal face plate

▪ Top cover metal plate

▪ Storage sub-system metal chassis

▪ Aluminum bottom chassis housing mixed

copper heat-pipe (installed with EITX-3000)

• Front I/O support:

▪ 4 x Serial ports (COM ports)

− D-Sub 9-pin COM connector

− COM1 ~ COM4 (two RS-232 and two

RS-232/422/485) from EITX-3000

▪ 1 x GPIO port (default GPIO cable connector)

− D-sub 9-pin GPIO male connector

▪ 2 x USB ports (USB 2.0 compliant)

▪ 1 x VGA connector

− D-sub 15-pin connector (from EMIO-3110)

▪ 1 x DC-in port (onboard power input)

− 2-pole Phoenix power input

▪ 1 x ATX Power On/Off button

▪ 1 x WLAN antenna hole

▪ 1 x Green LED indicator (Power On/Off status)

▪ 1 x Red LED indicator (HDD activities status)

• Rear I/O support:

▪ 1 x VGA connector

− D-sub 15-pin connector

▪ 2 x LVDS connectors

− DB-26 connectors as LVDS1 and LVDS2

▪ 2 x GigaLAN connectors

− RJ-45 connectors

− GigaLAN connectors as LAN1 and LAN2

▪ 2 x 3.5Φ Audio jacks

− Speaker-out and Mic-in

▪ 2 x HDMI ports

− HDMI1 and HDMI2 (from EMIO-3110)

▪ 2 x DVI ports (as DVI1 and DVI2)

• Board-level support:

▪ Compatible with VIA EITX-3000 embedded

board and EMIO-3110 module

• Drive bay:

▪ Default support 1 x 2.5” SATA hard disk drive

bay located on the storage bottom chassis

▪ Default support 1 x CompactFlash

type I/II socket (from EITX-3000)

• Mounting (optional):

▪ Supports VESA, table and wall mounting

• Dimension after assembly:

▪ 232.6 mm (W) x 73 mm (H) x 124.8 mm (D)

• Weight (front & rear plates and storage chassis):

▪ 0.8 kg

• Barebones weight (after assembly):

▪ 2.0 kg (front & rear plates, storage chassis and

aluminum bottom housing)

• Storage Temperature: -20˚C up to 60˚C

Front I/O cutout layout

Rear I/O cutout layout

Item Description

1 Power button (Power On/Off)

2 DC-in power input connector

3 USB 2.0 port 1 (USB1)

4 USB 2.0 port 2 (USB2)

5 COM2 port (RS-232/422/485)

6 COM1 port (RS-232/422/485)

7 Power LED indicator

Item Description

8 HDD LED indicator

9 WLAN antenna hole

10 COM3 port (RS-232)

11 COM4 port (RS-232)

12 GPIO port

13 VGA port

Item Description

14 VGA port

15 CompactFlash slot

16 LVDS port 1 (LVDS1)

17 LVDS port 2 (LVDS2)

18 RJ-45 GigaLAN port 2 (LAN2)

19 RJ-45 GigaLAN port 1 (LAN1)

Item Description

20 Mic-in jack

21 Speaker-out jack

22 HDMI port 1 (HDMI1)

23 HDMI port 2 (HDMI2)

24 DVI port 1 (DVI2)

25 DVI port 2 (DVI1)

Step 2

Locate the GPIO pinheader on the EITX-3000 mainboard and gently

connect the other end of GPIO cable.

Step 1

Break off the GPIO cutout filler. Then insert the D-sub 9-pin GPIO

connector into the GPIO cutout and fasten the provided hex standoff

screws to secure the connector.

• Operating Temperature:

▪ 0˚C up to 45˚C (system equipped with HDD)

▪ -20˚C up to 45˚C (system equipped with CF)

• Relative Humidity:

0% to 90% @ 45˚C, non-condensing

• EMC approved: CE, FCC, CCC Class A

• Safety approved: CB, CCC

Installing the

USB cable (optional)

Step 1

Locate the USB pinheader (USB_4/5) on the EITX-3000 board and

gently attach USB cable to the pinheader.

Step 2

Break off the USB cutout filler. Then attach USB cable port onto the

USB pre-cutout and fasten the screws to secure the USB cable port.

Installing the TV-out

cables (optional)

Step 1

Locate the TV-out pinheader (TV1) on the EMIO-3110 module and

gently attach Component video (YPbPr) cables to the pinheader.

Step 2

Break off the TV-out cutout filler. Then attach the other end (RCA

plugs) of the Component video (YPbPr) cables onto the TV pre-

cutout. And fasten the screws and nuts to secure the cables.

Installing the

GPIO cable

Installing board-to-

board audio cable

Step 1

Locate the audio pin header (JAUDIO1) on the EMIO-3110 module

and gently attach the board-to-board audio cable.

Installing the front

and rear I/O plates

VIA Technologies, Inc.

1F, 531, Zhong-Zheng Road,

Xindian, Taipei 23148

Taiwan

Tel: 886-2-2218-5452

Fax: 886-2-2218-5453

Web: www.via.com.tw

For more information on this and

other VIA products, please visit

www.viaembedded.com.

For further support and service,

please visit www.via.com/tw/en/

products/mainboards/contact.jsp

Step 2

Align the front and rear I/O plates to the heatsink. And install the

plates screws (P/N: 99G44-030231), HDMI screws (P/N: 99G44-

010415) and hex standoff screws (P/N: 99G44-030221) to the front

and rear connectors.

Dimensions

Installing WiFi (WLAN)

module (optional)

The WiFi kit should include the WiFi module, two screws, one board-

to-board cable, one mini coaxial cable, one washer, one nut, and one

external antenna. The optional WLAN module includes a VT6656

WLAN controller and provides support for 802.11 b/g standards.

Step 1

Flip the storage chassis (bottom case) over and align the WLAN

module over the WLAN mounting holes. Then secure it with two

mounting screws.

Step 3

Gently attach the WLAN board-to-board cable to the WLAN

pinheader (USB_2/3) on the EITX-3000 board and to the mini

connector on the WLAN module.

Step 2

Insert the WLAN port (with washer) into the antenna cutout and

fasten it with the nut. Then install the external antenna, and connect

the mini coaxial cable to the mini RF connector onto WLAN module.

Step 2

Attach the other end of the board-to-board audio cable to the

pinheader (F_AUDIO) on the EITX-3000 board.

Step 1

Remove all hex standoff screws from the front & rear I/O connectors

of EMIO-3110 module.

Installing hard disk

and storage chassis

Step 2

Mount the hard disk brackets on the 2.5” HDD. Then install the

brackets over the HDD mounting holes on the inside of the storage

chassis and secure it with four screws. And connect the other end of

SATA (data and power) cable to the hard disk.

Step 3

Install and secure the bottom case of the storage chassis to the

heatsink with eight mounting screws (P/N: 99G44-010415).

Step 4

Align the top cover of the storage chassis with the bottom case of the

storage chassis. Then secure it with three screws (P/N: 99G44-030231).

Step 1

Connect the SATA (data and power) cable onto the EITX-3000 board.

Step 1

Insert the memory module into the SODIMM socket at 45 degrees

angle. Then push down the memory module until its snaps into place.

Installing SODIMM

and EMIO-3110

Step 2

Align the Em-IO connector on the bottom side of EMIO-3110 with the

Em-IO connector on the EITX-3000. Connect the module to the board

and secure it with six screws.

VIA Technologies AMOS-5110 Quick Manual

VIA Technologies AMOS-5110 Quick Manual

VIA Technologies AMOS-5110 Quick Manual

Related papers

Other documents