Page is loading ...
ART-3000
Quick Guide
Key Features:
• Fanless, Compact and Rugged System
• Support Triple Display with Dual Independent Display
• Dual Gigabit Ethernet Support
• Wide Range of Power Source
• Flexible Mounting Options
The ART-3000 is a fanless embedded system intended for various indus-
trial and embedded applications. Its based on the Em-ITX form factor and
powered by a high performance VIA Nano processor. The ART-3000’s
system is designed with rugged aluminum alloy. It features a wall/VESA/
table-mountable design for easy installation. Its also support dual-sided
multiple connectors and has a wide range DC power input supporting AT
and ATX mode.
Step 1
Remove the screws on front and rear side of the chassis.
1
Step 2
Remove the screws on right and left side of the chassis.
P/N: 99G51-012994-10
Opening the Chassis
2
Installing the Memory
Step 3
Lift up the chassis top cover.
Step 3
Unscrew the two screws to remove the memory heatsink in order to
locate the memory slot.
Step 4
Insert the memory module into the SODIMM socket at the 45 degree
angle. Then push down until the memory module snaps into place. The
SODIMM socket has two locking mechanisms that will click once the
memory module has been fully inserted.
Specifications:
• CPU: VIA Nano 1.3 GHz processor (800 MHz FSB)
• System Chipset: VIA VX800 Unified Digital Media IGP
• System Memory:
• 1 x DDR2 533/667 MHz SDRAM SODIMM slot
• Supports memory sizes up to 2 GB
• Display: VIA Chrome™ 9 HC3 DX9 3D/2D IGP
• Supports MPEG-2, H.264 and WMV9 Decoding
• Support Dual Channel 24-bit LVDS panel
• Dual Independent Display
• Storage:
• 1 x 2.5-inch SATA hard disk bay
• 1 x CompactFlash disk (Type I/II) socket
• Audio: VIA VT1708B High Definition Audio Codec
• BIOS: Award BIOS ( 8Mbit SPI Flash )
• Front I/O:
• 2 x USB 2.0 ports
• 4 x COM ports (RS-232 and RS-232/422/485)
• 7V~36V DC-In power connector
• Rear I/O:
• 2 x USB 2.0
• 1 x VGA connector
• 2 x LVDS connector
• 2 x RJ45 port (Gigabit Ethernet connection)
• 2 x Audio jacks (Line-out and Mic-in)
• Power Input Voltage: DC 7V ~ 36V
• Power Consumption: Typical 18.5 W, Max. 25.8 W
• Dimensions: 233 mm (W) x 65.2 mm (H) x 123.5 mm
(D)
• Net Weight: 1.5 Kg (3.3 lbs)
• Operating Temperature:
• With CompactFlash disk only: -20°C ~ 60°C
• With 2.5-inch hard disk drive: 0°C ~ 45°C
• Humidity: 0% ~ 90% relative humidity (non-
condensing) @ 45°C
• Vibration loading during operation:
• CompactFlash = 5Grms
• 2.5-inch hard disk drive = 1Grms
• Shock during operation:
• CompactFlash = 50G
• Hard disk drive = 20G
• EMC Approved: CE/FCC Class A
Front I/O Layout
Item Description
1 Power button (Power On/Off)
2 Power input connector
3 USB 2.0 port 1 (USB1)
4 USB 2.0 port 2 (USB2)
5 COM2 port (RS-232/422/485)
Rear I/O Layout
Item Description
6 COM4 port (RS-232)
7 COM3 port (RS-232)
8 COM1 port (RS-232/422/485)
9 Power LED indicator
10 HDD LED indicator
Item Description
11 Line-out jack
12 Mic-in jack
13 USB 2.0 port 3 (USB3)
14 USB 2.0 port 4 (USB4)
15 VGA port
Item Description
16 CompactFlash slot
17 LVDS port 1 (LVDS1)
18 LVDS port 2 (LVDS2)
19 RJ-45 Gigabit Ethernet LAN port 2 (LAN2)
20 RJ-45 Gigabit Ethernet LAN port 1 (LAN1)
Step 1
First remove the hard disk brackets by unscrewing the four screws.
Step 2
Unscrew the four screws in order to remove the hard disk plate to
locate the memory heatsink.
Packing List:
• 1 x ART-3000 unit
• 1 x SATA cable
• 1 x SATA power cable
• 1 x Power cable, 2-pole Phoenix plug to DC-jack
• 1 x 0.5cc Thermally Conductive Dispensable Gel in tube syringe
• 1 x Memory heatsink
Important:
Please ensure that all items in the packing list are present before
using this product. If any of the items are missing or damaged,
contact your distributor or sales representative immediately.
VIA Technologies, Inc.
1F, 531, Zhong-zheng Road,
Xindian District, New Taipei City 231,
Taiwan
Tel: 886-2-2218-5452
Fax: 886-2-2218-5453
Web: www.via.com.tw
Copyright © 2013 VIA Technologies, Inc. All rights reserved.
For more information on this and
other VIA products, please visit
www.viaembedded.com.
The mainboard in the ART-3000 system supports two SATA ports
(SATA1 & SATA2) and two 3-pin SATA power (S-Power 1 & S-Power 2)
via onboard connectors. Each SATA port supports data transfer rates
up to 300MB/s enabling fast data transfer with independent DMA
operation. The SATA power connectors have 5V power source.
3
Installing the SATA
2.5-inch hard disk
4
Locating SATA and
SATA Power Ports
Step 6
Apply the thermal grease on the memory heatsink joint using the
syringe injection before placing the memory heatsink.
Step 7
Reinstall the memory heatsink cover. Secure the memory heatsink with
two screws.
Step 3
Align the mounting bracket with the mounting holes on the hard disk
plate. Secure the bracket in place with four screws. Then connect the
SATA power and data cables of the hard disk, also connect the other
ends of the cables to the SATA port and SATA power port onto the
board.
Step 1
Locate the CompactFlash access cover on the rear side of the ART-
3000 and remove the screw to remove the access cover.
Step 2
Ensure the proper orientation of CompactFlash card with the
CompactFlash slot before inserting.
Step 5
Peel the protective layers off of the memory thermal pad. Then apply
the thermal pad on the bottom of memory heatsink.
Step 1
Remove the SATA 2.5-inch hard disk mounting bracket.
Step 2
Prepare the hard disk screws and rubber washer. Align the mounting
holes on the SATA 2.5” hard disk with the mounting holes on the hard
disk mounting bracket. Secure the hard disk in place with four hard
disk screws.
Note:
Use the shorter screws when installing the brackets onto the
hard disk drive.
Note:
SATA1 & SATA2 ports can only supports 2.5-inch hard disk drive.
Important:
When connecting the SATA power cables via onboard S-Power 1
and S-Power 2 connectors, always make sure that the power plug
is inserted in the proper orientation and pins are properly aligned.
5
Installing the
CompactFlash Card
Step 3
Replace the CompactFlash access cover. Secure the CompactFlash
access cover with the screw.
6
Installing the
mounting Brackets
Step 1 (Default)
Prepare the left and right brackets and four screws.
Step 2
Fasten the mounting brackets, one each to the left bottom and right
bottom side of ART-3000 chassis with four screws.
Step 3 (Optional)
Position the mounting brackets on both upper sides of the chassis with
four screws.
Step 4
Secure the both mounting brackets to the wall/table with four screws.
/
