ACCESS LINK WITH OPTIONAL ACTIVATE
DAILY OPERATION INSTRUCTIONS
ENSURE THE SYSTEM IS POWERED ON
Power / Mute
2
1. Locate the 24V power supply and power cable and connect the AC power cord into the
DC power supply. Insert the DC connector into the DC Power jack on the back and
plug the AC power cord into an electrical outlet.
2. Press the Activate Station power button to power on the Access Link. When powered
on, the blue LED will glow.
Lightspeed Technologies
www.lightspeed-tek.com / 800.732.8999 / 503.684.5538
CHARGE FLEXMIKE NIGHTLY
9. Place the Flexmike into the charger. The power button light will glow red and the Mic status
light will glow blue. When Flexmike is fully charged, the power button light on the mic will
change to green.
USING A WIRELESS AUDIO LINK
2
7
8
7. Plug your external audio equipment (for example, laptop), into one of the input jacks on
the back of the Activate labeled “Aux Input” using a 3.5mm patch cable.
8. Adjust volume at the audio source. If necessary, further volume adjustment may be
made using the Audio In volume buttons on the front of the Activate.
3
4
5
For futher instructions on capturing audio and video using the Activate App, and for complete operating
instructions, go to www.lightspeed-tek.com/AL-usermanual (or scan the 2D barcode below).
9
QS0541US01-2
PLEASE FOLLOW ACCESS LINK SET UP INSTRUCTIONS ON OPPOSITE PAGE.
1
USING THE FLEXMIKE
3. Remove microphone from charger and place the microphone around your neck.
Ensure the top of the microphone is at the collarbone.
4. Press the power/mute button. The teacher status will turn blue, indicating the
microphone is active.
5. Microphone volume may be adjusted at the microphone by using the Up/
Down buttons on the side of the Flexmike. It may also be adjusted by using the
Microphone volume buttons on the front of the Activate.
6. For recording video, audio and images, ensure your mobile device is paired with
Activate. If not paired, refer to the Mobile Device Pairing Quickstart guide.
ACCESS LINK SET UP AND
DAILY OPERATION INSTRUCTIONS
ENSURE THE SYSTEM IS POWERED ON
AUDIO IN
MICROPHONE
AUDIO OUT
POWER
MIN
LINK
MAX
MIN MAX MIN MAX
5
4
4. Press the Access Link power button to power on.
5. When powered on, the blue LED will glow.
6. Remove microphone from charger and place the microphone around your neck. Ensure the top of
the microphone is at the collarbone.
7. Press the power/mute button. The teacher status will turn blue, indicating the microphone is active.
8. Microphone volume may be adjusted at the microphone by using the UP/DOWN buttons on the side
of the Flexmike. It may also be adjusted by using the MICROPHONE volume knob on the front of the
Access Link or the optional Media Connector.
1 4
322
1
AUDIO INAUDIO OUT
REGISTER
USB POWER
5V/1.5A
TONE
TREBLE BASS
CHARGE FLEXMIKE NIGHTLY
9. Place the Flexmike into the cradle
charger. The power button light will
glow red and the Mic status light will glow
blue. When Flexmike is fully charged, the
power button light on the mic will change
to green.
2
10
11
Power / Mute
6
7
8
9
AUDIO INMICROPHONE TONE
POWER
MIN
1
MAX MIN MAX TREBLE BASS
2
11
10. Plug your external audio equipment (for example,
laptop), into the Audio In 3.5mm jack on the back of the
Access Link, or into one of the input jacks on the back
of the optional Media Connector labeled “Audio In”, using
a 3.5mm patch cable.
11. Adjust volume at the audio source. If necessary, further
volume adjustment may be made using the Audio In
volume knob on the front of the Access Link or the Media
Connector.
USING A WIRELESS AUDIO LINK
REGISTER
USB POWER
5V/0.2A
+
–
AUDIO IN BAL. AUDIO OUT
AUDIO OUT
MIC LINE
AUDIO OUT/DC IN
AUDIO INMICROPHONE AUDIO OUT
POWER
MIN
LINK
MAX MIN MAX MIN MAX
Access Link Front
Access Link Back
Media Connector Front
Media Connector Back
For complete operating instructions, go to www.lightspeed-tek.com/AL-usermanual (or scan the 2D barcode on the previous page).
2
7
10
DETERMINE SET-UP LOCATION AND PLUG IN POWER SUPPLY
1. The Access Link is generally located near the amplifier.
2. Plug one end of the included 3.5mm cable into the AUDIO
OUTPUT connection on the Access Link. Plug the other end
into an audio input connection on the amplifier.
3. Use the Cat5e cable to connect a Lightspeed CAT 885 to
the Access Link to provide power and send audio through
the system. When connecting Access Link to a dierent
amplifier, plug the micro USB end of the power cable into the
USB port on the back of the Access Link. Plug the other end
of the cable into the USB1 power adaptor, then plug into an
outlet.
AUDIO INMICROPHONE
TONE
POWER
MIN
1
MAX MIN MA
X TREBL
E BASS
2
REGISTER
USB POWER
5V/0.2A
+
–
AUDIO IN BAL. AUDIO OUT
AUDIO OUT
MIC LINE
AUDIO OUT/DC IN
AUDIO AMPLIFIER
INPUT CONNECTION
3.5MM AUDIO CABLE
(INCLUDED)
2
3
3
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Lightspeed Redcat Access User guide
-
Lightspeed 955 Access User guide
-
Lightspeed Topcat User guide
-
-
-
-
-
-
-
Other documents
-
LightSpeed Technologies RedCat User manual
-
Sprint TREBL User guide
-
Harman TREBL Sprint Magic Box User guide
-
-
-
-
-
-
-