Page is loading ...
1
H3C LSPM6G4T6P interface card
user manual-6PW103
Introduction
Overview
The LSPM6G4T6P interface card provides four 10/100/1000Base-T
autosensing Ethernet ports and six SFP ports. 10/100/1000Base-T
autosensing Ethernet ports 5T and 6T form a combo interface with SFP
ports 5S and 6S, respectively.
Figure 1 LSPM6G4T6P interface card
(1) SFP port (2) 10/100/1000Base-T autosensing
Ethernet port
(3) Captive screw (4) 10/100/1000Base-T autosensing
Ethernet port LED
(5) Ejector lever (6) SFP port LED
NOTE:
The H3C switch models that the LSPM6G4T6P interface card is
applicable to might change over time. For the most recent list of
applicable switch models, contact H3C Support or marketing staff.
1
6
5 4
32
2
SFP ports
You can install the following transceiver modules and cables in the SFP
ports on the card:
• GE SFP transceiver modules in Table 1 and
Table 2.
• FE SFP transceiver modules in Table 3 and
Table 4.
• SFP cables in Table 5.
Table 1 GE SFP trans
ceiver modules available for the SFP ports (1)
Module Central wavelength (nm) Connector
SFP-GE-SX-MM850-A 850 LC
SFP-GE-LX-SM1310-A 1310 LC
SFP-GE-LH40-SM1310 1310 LC
SFP-GE-LH40-SM1550 1550 LC
SFP-GE-LH70-SM1550 1550 LC
SFP-GE-LH80-SM1550 1550 LC
SFP-GE-LH100-SM1550 1550 LC
SFP-GE-LX-SM1310-BIDI
TX: 1310
RX: 1490
LC
SFP-GE-LX-SM1490-BIDI
TX: 1490
RX: 1310
SFP-GE-T N/A RJ-45
Table 2 GE SFP transceiver modules available for the SFP ports (2)
Module
Cable/fiber
diameter
(μm)
Modal
bandwidth
(MHz × km)
Max transmission
distance
SFP-GE-SX-MM
850-A
Multi-mode,
50/125
500 550 m (1804.46 ft)
400 500 m (1640.42 ft)
Multi-mode,
62.5/125
200 275 m (902.23 ft)
160 220 m (721.78 ft)
SFP-GE-LX-SM1
310-A
Single-mode,
9/125
N/A 10 km (6.21 miles)
Multi-mode,
50/125
500 or 400
550 m (1804.46 ft)
Multi-mode,
62.5/125
500 550 m (1804.46 ft)
3
Module
Cable/fiber
diameter
(μm)
Modal
bandwidth
(MHz × km)
Max transmission
distance
SFP-GE-LH40-S
M1310
Single-mode,
9/125
N/A 40 km (24.86 miles)
SFP-GE-LH40-S
M1550
Single-mode,
9/125
N/A 40 km (24.86 miles)
SFP-GE-LH70-S
M1550
Single-mode,
9/125
N/A 70 km (43.50 miles)
SFP-GE-LH80-S
M1550
Single-mode,
9/125
N/A 80 km (49.71 miles)
SFP-GE-LH100-
SM1550
Single-mode,
9/125
N/A
100 km (62.14
miles)
SFP-GE-LX-SM1
310-BIDI
Single-mode,
9/125
N/A 10 km (6.21 miles)
SFP-GE-LX-SM1
490-BIDI
SFP-GE-T Twisted pair N/A 100 m (328.08 ft)
NOTE:
The SFP-GE-LX-SM1310-BIDI and SFP-GE-LX-SM1490-BIDI
transceiver modules must be used in pairs.
Table 3 FE SFP transceiver modules available for the SFP ports (1)
Module Central wavelength (nm) Connector
SFP-FE-SX-MM1310-A 1310 LC
SFP-FE-LX-SM1310-A 1310 LC
SFP-FE-LH40-SM1310 1310 LC
SFP-FE-LH80-SM1550 1550 LC
SFP-FE-LX-SM1310-BIDI
TX: 1310
RX: 1550
LC
SFP-FE-LX-SM1550-BIDI
TX: 1550
RX: 1310
LC
4
Table 4 FE SFP transceiver modules available for the SFP ports (2)
Module Fiber diameter (μm)
Max transmission
distance
SFP-FE-SX-MM13
10-A
Multi-mode, 50/125 2 km (1.24 miles)
Multi-mode, 62.5/125 2 km (1.24 miles)
SFP-FE-LX-SM13
10-A
Single-mode, 9/125 15 km (9.32 miles)
SFP-FE-LH40-SM
1310
Single-mode, 9/125 40 km (24.86 miles)
SFP-FE-LH80-SM
1550
Single-mode, 9/125 80 km (49.71 miles)
SFP-FE-LX-SM13
10-BIDI
Single-mode, 9/125 15 km (9.32 miles)
SFP-FE-LX-SM15
50-BIDI
Single-mode, 9/125 15 km (9.32 miles)
NOTE:
• The SFP-FE-LX-SM1310-BIDI and SFP-FE-LX-SM1550-BIDI
transceiver modules must be used in pairs.
• Only SFP ports 5S and 6S support FE SFP transceiver modules.
Table 5 SFP cables available for the SFP ports
Cable Cable length Data rate
SFP-STACK-Kit 1.5 m (4.92 ft) 1250 Mbps
NOTE:
A
s a best practice, use H3C SFP transceiver modules and SFP cables
for the SFP ports on the card. The H3C SFP transceiver modules and
SFP cables available for the SFP ports are subject to change over
time. For the most recent list of H3C SFP transceiver modules and SFP
cables available for the SFP ports, contact H3C Support or marketin
g
staff.
5
For more information about H3C SFP transceiver modules and SFP
cables, see H3C SFP/SFP+/XFP/SFP28 Transceiver Modules and
Cables Installation Guide at www.h3c.com.hk.
10/100/1000Base-T Ethernet interfaces
Table 6 10/100/1000Base-T Ethernet interface specifications
Item Specification
Connector RJ-45
Port mode
• 10 Mbps, full duplex
• 100 Mbps, full duplex
• 1000 Mbps, full duplex
• MDI/MDI-X autosensing
Maximum transmission
distance
100 m (328.08 ft)
Cable Category 5 or above twisted pair cables
Standard
• IEEE 802.3i
• 802.3u
• 802.3ab
LEDs
Table 7 describes LEDs for the SFP ports.
Table 7 SFP port LED description
LED status Description
Steady green
A transceiver module is installed in the port.
The port is operating at 1000 Mbps, and a
link is present on the port.
Flashing green
The port is sending or receiving data at
1000 Mbps.
Steady yellow
(available only for the
SFP ports 5 and 6)
A transceiver module is installed in the port.
The port is operating at 100 Mbps, and a
link is present on the port.
Flashing yellow
(available only for the
SFP ports 5 and 6)
The port is sending or receiving data at 100
Mbps.
6
LED status Description
Off
No transceiver module is installed in the
port, or no link is present on the port.
Table 8 10/100/1000Base-T interface LED description
LED status Description
Steady green
The port is operating at 1000 Mbps, and a link is
present on the port.
Flashing green
The port is sending or receiving data at 1000
Mbps.
Steady yellow
The port is operating at 10/100 Mbps, and a link
is present on the port.
Flashing yellow
The port is sending or receiving data at 10/100
Mbps.
Off No link is present on the port.
NOTE:
The LEDs are affected by the port mode switching button on your
switch. For more information about the port mode switching button,
see the installation guide for the switch.
Installing and removing the card
CAUTION:
• Before you install or remove the card, wear an ESD wrist strap and
make sure the wrist strap makes good skin contact and is reliably
grounded.
• To avoid device damage, do not use excessive force when you
install or remove the card.
The following procedures describe how to install and remove an
LSPM6G4T6P interface card on an S5560-30C-EI switch.
Prepare the following tools before you install or remove the card:
7
• Phillips screwdriver.
• Flat blade screwdriver.
• ESD wrist strap.
The installation tools are not provided with H3C devices. Prepare them
yourself.
Installing the card
1. Use the Phillips screwdriver to remove the screw on the filler panel in
the target slot, as shown by callout 1 in Figure 2.
K
eep the removed screw secure for future use.
2. Insert the flat blade screwdriver through the handle on the filler
panel to pull out the filler panel, as shown by callout 2 in Figure 2.
K
eep the removed filler panel secure for future use.
3. Unpack the card.
4. Insert the card slowly into the slot along the guide rails, as shown by
callout 1 in Figure 3.
5. Rotate in
ward the ejector lever as shown by callout 2 in Figure 3
until the
card is in close contact with the switch.
6. Use the Phillips screwdriver to tighten the captive screw on the card,
as shown by callout 3 in Figure 3.
Figure 2 Rem
oving the filler panel
8
Figure 3 Installing the card
Removing the card
CAUTION:
• Before you remove the card, remove the cable from it.
• If you are not to install a new card after removing the original one,
install the filler panel in the slot to prevent dust and ensure good
ventilation in the device.
To remove the card:
1. Prepare an anti-static bag.
2. Use the Phillips screwdriver to loosen the captive screw on the card,
as shown by callout 1 in Figure 4,
3. Rotate out
ward the ejector lever as shown by callout 2 in Figure 4.
4. P
ull the card slowly out of the slot as shown by callout 3 in Figure 4.
5. Place
the removed card in the anti-static bag.
9
Figure 4 Removing the card
Installing and removing SFP transceiver modules or SFP
cables
For information about installing or removing SFP transceiver modules or
SFP cables, see H3C SFP/SFP+/XFP/SFP28 Transceiver Modules and
Cables Installation Guide at www.h3c.com.hk.
Verifying the installation
After the installation is complete, identify whether the card is operating
correctly according to the status of the port LEDs.
If the card fails to operate correctly, perform the following steps:
1. Reinstall it following the installation procedures described in this
document.
2. If the problem persists, contact H3C Support.
Technical support
New H3C Technologies Co., Ltd. provides customers with
comprehensive technical support and service. If you purchase the
products from the sales agent of New H3C Technologies Co., Ltd.,
please contact our sales agent or technical personnel.
Website: http:// www.h3c.com.hk
E-mail: service@h3c.com
BOM: 3101A0K3
2
3
1
/
