Anova F1031 Assembly Instruction

Brand: Anova

Model: F1031

Type: Assembly Instruction

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• 1/2" Open-end or box-end wrench

• Ratchet with 1/2" socket

• Level

Assembly Instructions

Courtyard

F1031 - Courtyard 4' Gullwing Bench

F1035 - Courtyard 6' Gullwing Bench

BENCH COMPONENTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

(2) Bench Supports (1) Bench Seat (2) Cross Braces (2) Arm Rests

(12) 5/16" - 18 X 1 1/4"

Hex Head Bolts

(24) 5/16" Flat

Washers

(12) 5/16" - 18

Nylock Nuts

(4) Rubber Feet

(Included but not

necessary for assembly)

ASSEMBLY:

Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.

2. Lay all parts on a so work surface or on the shipping packaging to prevent damage to nish.

3. Locate one of the bench supports and position it near the end of

the seat.

Align the mounting holes in the bench support with the holes in

the bracket on one end of the bench seat. Place a at washer onto

a 1 1/4" hex head bolt and insert the bolt through both parts, with

the bolt head on the outside surface of the bench seat. Place a at

washer and nylock nut on the inside end of the bolt and tighten it

nger tight.

Insert a 1 1/4 " hex head bolt and at washer through the other

set of mounting holes in that end of the bench seat and support.

Place a at washer and nylock nut on the end of the bolt and

tighten nger tight.

NOTE: Before assembling the nuts to the bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.

Courtyard 4' Gullwing Bench Courtyard 6' Gullwing Bench

Bench Seat Support

Bench Seat

5/16" - 18 X 1 1/4"

Hex Head Bolt

5/16" Flat Washer 5/16" Flat

Washer

5/16" - 18

Nylock Nut

Seat Bracket Support

The assembly is a two-person operation.

NOTE: Installing the bolts in this direction reduces the risk of

scratching during use.

Attach the other bench support to the bench seat in the same

manner, installing the bolts from the outside inward. Leave

the hardware nger tight.

Locate a cross brace and position it so that the mounting

hole in one end aligns with the mounting hole in the bracket

in the center of the seat support. Place it on the back side

of the bracket. Place a at washer on a 1 1/4" hex head bolt

and insert the bolt through the cross brace and seat support

bracket and place a at washer and nylock nut on the end of

the bolt and tighten nger tight so that adjustments can be

made while assembling and leveling.

Insert a 1 1/4" hex head bolt and at washer through the

mounting holes in the other end of the cross brace and seat

center bracket. Place a at washer and nylock nut on the end

of the bolt and tighten nger tight.

Attach the other cross brace to the seat and the other seat

support in the same manner. Leave the hardware nger tight.

Turn the bench upright. Locate an arm rest and position it at one end

of the bench seat. Line up the holes in the armrest with the mounting

holes in the bench seat end. Place a at washer on 1 1/4" hex head

bolt and insert the bolt through the arm rest and through the

mounting hole in the bench seat. Place a at washer and nylock nut

on the end of the bolt and tighten nger tight. Repeat this process

for the other end of the arm rest. Aer both sets of hardware are

installed, tighten with the 1/2" open-end or box-end wrench and a

ratchet with a 1/2" socket.

Attach the other arm rest at the other end of the bench seat in the

same manner.

Tighten all hardware while checking with a level.

Move the assembled bench to the desired location.

Aer two weeks, retighten all of the hardware.

NOTE: The feet of the bench include surface mounting holes in case a permanent installation

is desired. Follow installation instructions provided with the hardware if purchased.

10.

5/16" - 18 X 1 1/4"

Hex Head Bolt

5/16" - 18

Nylock Nut

5/16" Flat Washer

5/16" Flat

Washer

Cross Brace

5/16" Flat Washer

Arm Rest

5/16" - 18 Nylock Nut

5/16" Flat Washer

5/16" - 18 X 1 1/4"

Hex Head Bolt

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

01/31/2018

22.50"

66.94"

4 X O .63"

43.06"

F1031 - Courtyard 4' Gullwing Bench Foot Mount

F1035 - Courtyard 6 ' Gullwing Bench Foot Mount

Bench Seat

Arm Rest

Bench Support

Cross Brace

Assembly and Replacement Parts

Anova F1031 Assembly Instruction

Anova F1031 Assembly Instruction

Anova F1031 Assembly Instruction

Related papers

Other documents