18
STAGE PAGE
76 Upper left engine block 289
77 Left side of the engine block 292
78 Upper right engine block 295
79 Front cover of the engine block
and the pulleys 298
80 Right side of the engine block 302
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2021
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
289
Ford GT
Faros y capÓ
76-A Left cylinder head
76-B Upper left engine block
76-C FP01 2.3 mm x 4 mm Ø
3.8 mm screws
Your parts
Note: The parts may differ slightly from those in the photos.
76-A
76-B
FP01
Stage 76: Upper left
engine block
STEP BY STEP
290
STEP 76-1
Position the left cylinder
head (76A) over the
upper left engine block.
The cylinder head has two
different-sized linchpins
which must be aligned
with the corresponding
holes in the block.
STEP 76-3
Turn the structure over and
secure the pieces with two FP01
screws.
STEP 76-2
Attach the left cylinder
head (76A) to the upper
left engine block (76B)
and check that the two
parts are joined correctly.
76-A
76-B
Ergot
fin
Gros
ergot
FP01
291
Ford GT
STAGE COMPLETE
STEP BY STEP
292
Faros y capÓ
77-A Left side of the engine
block
77-B Hydraulic brake hose
77-C FP02 1,8 x 4 mm Ø 3 mm
screws
Stage 77: Left side of the
engine block
Your parts
FP02
77-A
77-B
293
Ford GT
STEP 77-3
Now get the piece you
assembled in the previous
pack. Insert the linchpin
end of the hydraulic brake
hose (77B) into the hole
in the subframe (71A) you
received with the previous
pack, which is located
just below the left engine
mount (75A). Don’t press
too hard when inserting
the hose.
STEP 77-2
Turn the piece over and
secure the upper left engine
block (76B) to the left side of
the engine block (77A) using
two FP02 screws.
STEP 77-1
Get the piece you assembled
in the previous pack. Attach
the upper left engine block
(76B) to the left side of the
engine block (77A). To do
this, insert the square linchpin
in the centre of the upper
left engine block into the
corresponding hole in the left
side of the engine block, as
demonstrated.
Linchpin
77-A
77-B
77-A
FP02
76-B
76-B
71-A
75-A
Square
linchpin
STEP BY STEP
294
STEP 77-4
Slide the free end of
the hydraulic brake
hose (77B) onto the
linchpin on the outside
of the rear left brake
caliper (70D). Make
sure the hose fully
covers the linchpin.
STAGE COMPLETE
Linchpin
77-B
70-D
295
Ford GT
295
78-A Right cylinder head
78-B Upper right engine
block
78-C Oil filler tube
78-D FP01 2.3 x 4 mm Ø 3.8
mm screws
Your parts
78-A
78-B
78-C
FP01
Stage 78: Upper right
engine block
STEP BY STEP
296
STEP 78-1
Position the oil ller tube
(78C) over the right cylinder
head (78A). Insert the tube
into the corresponding hole,
then turn the cylinder head
over and secure the tube
with a FP01 screw.
STEP 78-3
Turn the structure over and
secure the pieces with two FP01
screws.
STEP 78-2
Position the right cylinder head
(78A) over the upper right
engine block. The cylinder
head has two different-sized
linchpins which must be aligned
with the corresponding holes in
the block. Attach the cylinder
head to the upper right engine
block by pressing down rmly
and then check that the two
parts are joined correctly.
78-A
78-A
78-B
Thin
linchpin
Wide
linchpin
FP01
78-C
FP01
297
Ford GT
STAGE COMPLETE
Note: La photo correspond à un prototype.
STEP BY STEP
298
Faros y capÓ
79-A Oil sump
79-B Engine block front
cover
79-C Pulley mechanism
79-D Alternator
79-E Manifolds
79-F FP01 screws
2.3 x 4 mm Ø 3.8 mm
79-G FP07 screws
2.3 x 4 mm Ø 5.2 mm
Stage 79: Front cover of the
engine block and the pulleys
Your parts
79-A
79-B 79-C
79-D
79-E
FP01
FP07
299
Ford GT
STEP 79-1
Position the alternator (79D)
over the pulley mechanism (79C).
Insert the two linchpins on the
alternator into the holes in the
pulley mechanism, as shown. After
attaching the alternator, secure it
with one FP01 screw.
STEP 79-3
Position the front cover of the engine
block (79B) over the manifolds (79E)
and pulley mechanism (79C). Insert
the linchpin on the mechanism into
the hole in the front cover and the
protrusion on the cover into the hole in
the manifolds, as shown. Secure all the
pieces with two FP01 screws.
STEP 79-2
Position the manifolds (79E) over
the pulley mechanism (79C), next
to the alternator (79D). Insert the
linchpin on the pulley mechanism
into the hole in the centre of the
manifolds, as shown. Note: the
manifolds must be either side of
the part of the pulley mechanism
that is opposite the alternator.
79-E
79-E
79-D
79-D
79-C
79-C
79-C
79-B
Linchpins
Ergot
Protrusion
FP01
FP01
STEP BY STEP
300
STEP 79-4
Get the left side of the engine block (77A). Put the piece you just assembled in the correct position.
Insert the linchpin into the hole in the right side of the engine block, as shown in the photo.
STEP 79-5
After attaching the front cover
(79B) to the left side of the engine
block (77A), turn the piece over
and secure the parts with one
FP01 screw from the inside of the
engine block.
62-A
Linchpins
79-B
79-B
77-A
FP01
77-A
301
Ford GT
STEP 79-6
Insert two FP07 screws into
the two protrusions on the
back of the oil sump (79A).
Do not over tighten the
screws as they will be used
to attach the oil sump to the
engine block.
STAGE COMPLETE
79-A
FP07
STEP BY STEP
302
Faros y capÓ
80-A Right side of the
engine block
80-B Hydraulic brake hose
80-C FP02 screws
1.8 x 4 mm Ø 3 mm
80-D FD08 screws
2.3 x 4 mm Ø 3.8 mm
Stage 80: Partie droite
du bloc moteur
Your parts
80-A
80-B
FP02
FD08
303
Ford GT
STEP 80-1
Get the piece you assembled in the previous
pack. Attach the upper right engine block
(78B) to the right side of the engine block
(80A). To do this, insert the square linchpin
in the centre of the upper right engine
block into the corresponding hole
in the right side of the engine
block, as demonstrated.
STEP 80-3
Now get the piece you
assembled in the previous pack.
Insert the linchpin end of the
hydraulic brake hose (80B) into
the hole in the subframe (71A)
you received with the previous
pack, which is located just below
the left engine mount (75B).
Don’t press too hard when
inserting the hose.
71-A
75-B
78-B
80-A
80-A
78-B
78-A
78-A/78-B
80-A
Ergot
carré
FP02
80-B
STEP 80-2
Turn the piece over and secure
the upper right engine block
(78B) to the left side of the
engine block (80A) using two
FP02 screws.
71-A
75-B
78-B
80-A
80-A
78-B
78-A
78-A/78-B
80-A
Ergot
carré
FP02
80-B
STEP BY STEP
304
STEP 80-4
Slide the free end of the
hydraulic brake hose
(80B) onto the linchpin
on the outside of the
brake caliper (66D) you
assembled together with
the rear right wheel.
Make sure the hose fully
covers the linchpin.
STEP 80-6
Insert the left side of the engine
block (77A) under the tab on
the back of the left side of the
transmission case (60A). Get the
oil sump (79A) with the two
FP07 screws inserted. Loosen the
screws slightly, position the oil
sump under the left engine block
(with the square recess facing
the engine) and carefully insert
the screws into the semi-circular
holes in the engine block.
Tighten the two FP07 screws
without forcing them.
80-B
66-D
Ergot
Linchpin
STEP 80-5
Get the left side of the engine
block (77A) and the completed
carburettor you assembled in
the previous packs. Position the
engine block over the intake
manifold (5B ) as shown, join the
two parts and then secure the
pieces with two FD08 screws.
77-A
77-A
77-A
60-A
5-B
FD08
79-A
FP07
Square
recess
305
Ford GT
STAGE COMPLETE
STEP 80-7
Slide the right side of the engine block (80A) onto the
tab on the back of the right side of the transmission case
(61A) and onto the two FP07 screws in the oil sump (79A).
Insert the two linchpins on the right engine block into
the holes in the left side of the engine block (77A). Check
that everything is assemble correctly and then secure the
pieces with two FD08 screws.
77-A
61-A
FD08
80-A
79-A
Linchpins
/