Deagostini Ford GT User guide

Brand: Deagostini

Model: Ford GT

Type: User guide

STAGE PAGE

3The right front wheel 13

4The right door 17

5The front bonnet cover 21

Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.

Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.

Warning: Not suitable for children under the age of 14.

is product is not a toy and is not designed or intended for use in play.

Items may vary from those shown.

FORD GT

3-A Wheel outer

3-B Wheel centre

3-C Wheel inner

3-D Disc brake 1

3-E Disc brake 2

3-F Brake caliper

3-G Brake cooling tube socket

3-H Wheel nut

3-I Screws FD01 2.3 x 4mm

3-J Screws FD02 2.3 x 3mm

3-K Screws FP01 2.3 x 4mm

Stage 3:

The right front wheel

3-A

3-B

3-C

3-D

3-E

3-H

3-G

3-F

YOUR PARTS

To help you assemble your model, with this

delivery you will receive a screwdriver of the

correct size and thickness for the screws used.

You will not need any other tools.

FD01

FD02

FP01

STEP BY STEP

STEP 3-1

Align the holes in the

wheel centre (3-B) with

the corresponding pins

in the wheel outer (3-A).

Carefully place the wheel

centre into position.

STEP 3-2

Lay the wheel inner (3-C)

over the wheel centre,

placing the posts onto the

pins projecting through the

holes of the centre.

STEP 3-3

Place the brake cooling tube socket (3-G)

into the corresponding hole of disc brake 1

(3-D). These parts can only t together in one

orientation due to the notches.

STEP 3-4

Secure the socket from behind

with an FP01 screw.

3-B

3-C

3-D

3-G

FP01

3-A

Hole

Notch Notch

3-D

FORD GT

STEP 3-5

Place disc brake

2 (3-E), onto disc

brake 1, as shown.

STEP 3-6

Place the brake caliper

(3-F) over brake discs 1

and 2. Secure with an

FD01 screw (inset).

STEP 3-7

Place the brake

assembly inside the

wheel, inserting the

axle of the brake

into the hole in

the centre of the

wheel. Align the

lug indicated on

the wheel (3-B)

with the slot in the

brake disc.

3-D

3-E

3-F

FD01

Slot

Lug

STEP BY STEP

STAGE COMPLETE

STEP 3-8

Turn the entire assembly

over and secure the brake to

the wheel with a FD02 screw.

STEP 3-9

Place the wheel nut (3-H) in the

centre hole of the wheel, over

the screw. It is magnetic, so it

will be held in position.

STEP 3-10

Here is how the wheel

assembly should look at the

end of this stage.

FD02 3-H

FORD GT

Stage 4:

The right door

4-A Right door

4-B Window

4-C Exterior door light

4-D Interior door panel

4-E Interior door compartment

4-F Interior door compartment

cover

4-G Door ceiling panel

4-H Hinge

4-I Hinge plate

4-J Opening mechanism plate

4-K Opening mechanism

4-L Opening mechanism spring

4-M Screws FP01 2.3 x 4mm

4-N Screws FP02 1.8 x 3.5mm

4-NN Screws FD03 1.8 x 3.5mm

Ø 4.5mm

4-O Screws FD04 1.8 x 3.5mm

4-P Screws FD01 2.3 x 5mm

YOUR PARTS

FP01 FP02 FD03 FD04 FD01

4-A

4-B

4-C

4-D

4-E 4-F

4-G

4-I

4-J

4-H

4-K

4-L

STEP BY STEP

STEP 4-1

Place the exterior door light (4-C) into the

hole in the door (4-A). They can only t

together in one orientation.

STEP 4-4

Place the hinge plate (4-I) onto the inside of the

door, over the hinge, and secure with an FD01 screw.

Check that the hinge can rotate, and loosen the

screw holding the plate in place if it doesn’t.

STEP 4-2

Hold the light in place and secure it from the inside

of the door with an FP02 screw.

STEP 4-5

Insert the opening mechanism (4-K) into the opening

mechanism spring (4-L). Place the two parts into the

the corresponding area at the rear of the door.

STEP 4-3

Place the hinge

(4-H) into the

corresponding

recess in the right

door (4-A).

4-C

4-H

4-I

4-K

4-L

4-A

Notch

FP02

FD01

4-A

FORD GT

STEP 4-6

Place the opening

mechanism plate (4-

J). Secure with two

FD04 screws.

STEP 4-7

Place the door ceiling

panel (4-G) onto the

inside of the door (4-A).

Match the four pins

with the four holes and

press the parts together.

STEP 4-8

Pass the bottom of the window (4-B) through the

opening in the door and secure to the three posts

with FD03 screws.

STEP 4-9

Take the inner door panel (4-D) and place the

inner door compartment (4-E) onto the pin and

two posts on the inside of the panel. Secure with

an FP01 screw.

4-K

4-J

4-G

4-A

4-B

4-D

4-E

FD04

FD03

FD04

FP01

STEP BY STEP

STEP 4-11

Fix the inner door compartment cover (4-F) into the space in the

inner door panel, pressing it in so that the tabs engage.

STAGE COMPLETE

STEP 4-10

Place the inner door

panel (4-D) onto the

inside of the door

(4-A), matching the

holes in the opening

of the panel with

those in the door. Fix

in position with two

FD01 screws.

4-A

4-D

4-D 4-F

Notches

FD01

Tab

FORD GT

5-A Bonnet cover

5-B Inner central column

5-C Bonnet closures

Stage 5:

The bonnet cover

YOUR PARTS

5-A

5-C 5-C 5-C 5-C

5-B

STEP BY STEP

STEP 5-1

Recover the bonnet

(1A) supplied with

Stage 1.

STEP 5-2

Place the bonnet cover

(5-A) into the opening in

the bonnet (1-A).

1-A

5-A

1-A

STEP 5-3

Make sure that the

bonnet cover (5-A)

ts correctly in the

bonnet, as shown.

5-A

1-A

FORD GT

STEP 5-5

Keep the inner

central column (5-B)

in a safe place for

use in a later stage.

STEP 5-4

Place the four bonnet

closures (5-C) into the

four slots in the bonnet

cover. Turn them to lock

the cover in position.

STAGE COMPLETE

5-C

5-B

Deagostini Ford GT User guide

Deagostini Ford GT User guide

Deagostini Ford GT User guide

Related papers

Other documents