FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Subpart J of Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which the
receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
FCC Warning
To assure continued FCC compliance the user must use grounded power supply core
and the provided shielded video interface cable with bonded ferrite cores.
If a BNC cable is going to be used, use only a shielded BNC(5) cable. Also,
any unauthorized changes or modifications no expressly approved by the party
responsible for compliance could void the user’s authority to operate this device.
© Copyright 2005 Vision® Ver 1.0
All brand names and trademarks are the registered property of their respective
owners.
i
ii
Table of Contents
1. Introduction
1-1. Features………………………………………………….……01
1-2. Specification…………………………………………….….…01
1-3. Package Contents……………………………………….…….02
1-4. Location of Controls (Box Set)……………………………….03
1-5. Location of Controls (Remote) ………………………………04
2. Set Up
2-1. Connecting TV Antenna/Cable………………………….….…05
2-2. Connecting Video Out To Monitor …….……………….…….05
2-3. Connecting Video Input From PC……………………….…….06
2-4. Connecting Audio Line Input/Output…………………….……06
2-5. Connecting Power Supply……………………………….…….07
2-6. Connecting Audio/Video Equipment…………………….…….07
3. Operation
3-1. Watching TV Programs…………………………..……….…….08
3-2. Convenient Remote Functions…………………..……….……..09
3-3. Adjusting the Picture……………………………..……….…….12
1
1.Introduction
Congratulation! You have purchased the KWORLD TV BOX WS to enhance your
multimedia PC. We will guide you through all of the features installation and operation.
This manual will help you use the many exciting and useful features to make your TV
viewing more enjoyable than ever before.
1-1.Features
z Watch live broadcast TV or cable TV on your LCD monitor
z Built with cable ready TV tuner with 181 channels (CATV 125 Channels) and
automatic channel scan function.
z Support SVGA(800x600),XGA (1024 x 768 ), SXGA(1280 x 1024),
WXGA(1440 x 900), and SXGA+(1400x1050)
z Auto Channel memorized to set up channels automatically
z Video / S-Video support NTSC, PAL system
z Connect game console, V8,DV, VCD/DVD player for viewing on your monitor
z Easy used. Don’t need to power on PC then you can watch TV program
z Full function remote control
1-2.Specification
z RF Input: 75Ω coaxial input for broadcast TV or cable TV
z Support TV System: PAL/SECAM/NTSC
z Video Resolution: 800x600,1024x768, 1280x1024,1440x900,1600x1200,
1400x1050,1680 x 1050 (PC signal depends on PC setting)
z Signal Input: S-video, composite, PC VGA (D-sub), audio
z Signal Output: PC VGA (D-sub), audio
1-3.Package Contents
z KWORLD TV BOX WS
z VGA cable
z 3.5mm mini Stereo Audio cable
z Remote controller
z Batteries
z DC 5V power adapter
z User’s manual
2
TV BOX WS Remote control VGA Cable
Power Adaptor Stereo Audio Cable AAA Batteries
Check to make sure that all the components are present and that nothing is damaged during shipping. If you
encounter any problems, please contact your dealer.
1-4.Location of Controls (Box Set)
Game Console
Video Camera
DVD Player
Power ON/OFF
Input Source Change
Channel+
Channel-
Volume+
Volume-
Power Adapter
Power Adapter
UHF/VHF antenna RF input device
VGA input from PC
VGA output to CRT/LCD
Audio in from PC
Audio Line output to Speaker
Front Panel
Rear View
3
1-5.Location of Controls (Remote)
[POWER]: Power button
[RESOLUTION]: Change the Video Resolution
[INPUT]: Change Video Source
[PC/Video]: Select PC or Video
[Sleep]: Sleep Time Select button
[0~9]: Channel Number buttons
[Recall]: Channel Recall button
[Select]: Confirm Setting or OSD show up.
[ ][ ][ ][ ]: Adjusting Picture Quality
[EXIT]: Exit Select key or Menu button
[Menu]: Select Item for Adjusting Function
[VOL-]: Volume Down button
[VOL+]: Volume Up button
[CH-]: Channel Down button
[CH+]: Channel Up button
[PIP]: Activate PIP mode button (OPTION)
[FAV]: Sets the current channel to “Favorite Channel”.
[Preview]: Channel Preview button
[Mute]: Audio Mute button
[MTS]: Stereo/SAP/Mono Select button (option)
4
2.Set Up
2-1.Connecting TV Antenna/Cable
You can use either an indoor or outdoor antenna to VHF and/or UHF channels.
You can receive Cable TV by connecting a cable supplied by
your local cable company。
75 ohm coaxial cable
300 ohm twin-lead
Antenna
OR
VHF, UHF or Cable TV
TV signal input
Rear View
2-2. Connecting Video Out to Monitor
5
VGA out
VGA out to LCD Monitor cable
Monitor
Rear View
2-3. Connecting Video Input from PC
6
VGA input
VGA cable
VGA (D-sub)
PC
2-4.Connecting Audio Line Input/Output
Audio in
Audio out
Audio Cable
PC
Audio Cable
Line in
Speaker
2-5. Connecting Power Supply
7
DC 5V Input
AC/DC Adaptor
2-6. Connecting Audio/Video Equipment
Video Source Input
Left Audio Channel Input
Right Audio Channel Input
S-Video Source Input
Front View
3.Operation
3-1.Watching TV Programs
※To select channel
1. Press POWER button to turn on or turn off.
2. Select a channel in one of the following two ways.
To scan the memorized channels in numerical sequence:
Press CH+ to select the next higher channel.
Press CH- to select the next lower channel.
To select a channel directly:
Press the Channel Number buttons (0~9)
Example: To select channel 7, press “0”, “7”, than Press Select
To select channel 12, press “1”, “2”, than Press Select
To select channel 120, press “1”, “2”, and “0”
※To change quickly between two channel
1. Select the first channel you want to view.
2. Select the other channel with the Channel Number buttons (0~9) or CH+/CH-
button.
3. Press Recall button. The previous channel will return. Each time you press Recall
button, the TV will switch back and forth between the two channels.
8
Note: In TV mode, you can press or button to select channel up or down.
※Sound volume
1. Press VOL + to increase
the volume. The segment of the indicator increases.
2. Press VOL- to decrease the volume. The segment of
the indicator decreases.
※To mute the sound
1. Press MUTE button to mute the sound. The mute
icon will be displayed on the screen.
2. To restore the sound, press MUTE button again, and the mute icon will disappear.
Note: In TV mode, you can press or button to adjust volume.
3-2. Convenient Remote Functions
※Selecting AV mode
1 Press POWER button to turn on into TV mode.
TV mode
AV mode
S-Video mode
2 When you press INPUT button each time, the
TV, AV, and S-Video input source will be
automatically changed by loop.
※Switching PC/AV mode
1 Press POWER button to turn on into TV mode.
The green LED of power lamp and mode lamp
are light.
2 Press PC/VIDEO button to switch to PC mode. The red LED of mode lamp is light.
※Selecting PC/VIDEO mode
1 Press PC/VIDEO button again to switch to TV mode. The green LED of mode
lamp is light.
9
※To change video resolution
1When you press RESOLUTION button each time, the 800x600,1024x768,
1280x1024 etc. resolution will be automatically changed by loop on any video mode
(e.g. TV, AV, S-VIDEO etc. mode).
Note: Press Menu button to resolution 1440 x 900, if your display no support this
mode, for example the screen show “ out of range”. Please press the Menu
button back to your optimum resolution.。
TV mode
※To display on-screen information
1In TV mode:
Press Select button to display the Channel number,
System, MTS, Volume on-screen information.
2In AV mode:
AV mode
PressSelect button to display the “AV” on-screen.
3In S-Video mode:
S-Video mode
PressSelect button to display the “S-VIDEO”
on-screen.
※To set the Sleep timer
You can set TV or other AV mode to turn off automatically after a predetermined
period of time (up to 120 minutes). Each time press SLEEP button, the time display
will increase.
OFFÆ5Æ10Æ15Æ30Æ60Æ90Æ120 min
Note:To cancel the off-timer, press POWER button to turn off or press SLEEP button to reset to time
off.
10
11
※FAVORITE(FAV) Channel Memory Setting
The favorite channel setting function provides 9 channels for setting your own
favorite channels. You can set your favorite channel from your remote control unit.
1. Choose the channel and press FAV button on the remote control, then
“FAVORITE“menu will pop up.
Favorite
1.CH-_ _
2.CH-_ _
3.CH-_ _
4.CH-_ _
5.CH-_ _
6.CH-_ _
7.CH-_ _
8.CH-_ _
9.CH-_ _
2. Press the Select to pick a number from 1 to 9.
3. When you want to watch your favorite channel. Into the “FAVORITE” and press
the number that your favorite channels.
※Preview Function(9 Channels Preview)
If you want to preview the TV channel, you can press this key, then the TV
Program will show on your screen one by one in 9 windows, and you can press
numeric key twice to cancel the preview.
Note: This function is only valid in TV mode.
12
3-3.Adjusting the Menu
Main Menu
Press the Menu button on the remote control, to set up and exit the main menu or
submenu on screen. Then you can use the " ↑ " or " ↓ " key,，select your items, than
press Select button into submenu to adjustable by
Æ "or " Å " to make a selection. You
can press Exit to leave the MENU mode.。
Main Menu
Submenu USAGE
Brightness
Contrast
Saturation
Hue
Sharpness
Noise Reduction
You can use the “↑ “or” ↓ " button to
Select the items in submenu. Then,
you can use the "Æ "or " Å " buttons
to make adjustment.
Picture Mode
Customized 3 Mode picture Viewing.
Picture Setting
Reset
Return to default picture settings
TV Source
。AIR 。Cable
Use "Æ "or " Å " buttons to change。
TV System
。PAL D/K
Use the "Æ "or " Å " buttons to
change TV System.
Channel Scan
Frequency Scan
These 2 types of channel scan
functions enable you to memorize all
active channels in your area.
USE the Channel Scan function first.
If some channel missing after you
play Channel Scan, use Frequency
Scan to searching again.
Finetune
If the TV reception is not clear,
choose FINE TUNE then press " Æ
"orÅ " buttons until the picture
becomes clear
CHANNEL +/-
The channels are not actually
removed or added but skipped from
or recovered to the channel table.
You can still select the removed
channel by pressing the channel
number.
TV Setting
CHANNEL Edit
USE the "Æ " " Å " buttons to select
TV System “D/K” or “B/G” for some
mix different TV system area.
13
OSD Position
Press the “Select” button to choose
the “OSD Position”, and use “↑ “” ↓
" "Æ " " Å "
buttons to move the position of menu
position on the display..After setting,
press the “Exit” button to return to the
OSD Setting sub-Menu.
OSD Transparency
Press the “Select” button to choose
the “OSD Transparency”, and use "
Æ "orÅ "
buttons to adjust degree.
LANGUAGE
。English 。中文
Use "Æ "or " Å " buttons to change,
then press “Select”.
RESOLUTION
USE the “↑ “” ↓ " "Æ " " Å " buttons to
choose resolution settings.
Information
Model Name & Version
OSD Setting
Restore all settings
USE the "Æ " " Å " buttons to select
“Yes” or “No” to restore all settings.
/
