Rugged Ridge 11210.15 Installation guide

Type
Installation guide

This manual is also suitable for

Rugged Ridge 11210.15 Aluminum Hood Catch is a supplemental hood latch designed for Jeep® TJ models. It provides additional security to the front latch and prevents the hood from accidentally opening due to vibrations or rough terrain. The catch is adjustable to ensure a snug fit, and it comes with all necessary hardware for easy installation.

Rugged Ridge 11210.15 Aluminum Hood Catch is a supplemental hood latch designed for Jeep® TJ models. It provides additional security to the front latch and prevents the hood from accidentally opening due to vibrations or rough terrain. The catch is adjustable to ensure a snug fit, and it comes with all necessary hardware for easy installation.

460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Page 1/3
11210.15 (Black)
11210.18 (Textured)
JEEP® TJ ALUMINUM HOOD CATCH
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
Contents:
A - Latch
B - Latch Joint
C - Pivot Base Joint
D - Pivot Base
E - Catch
F - Pivot Base Gasket
G - Catch Gasket
H - Flat Head Bolts
I - Lock Nuts
J - Binding Posts
K - Jam Nuts
L - Adjustment Rod
M - Safety Snap
Suggested Tools:
Basic Hand Tools
A
B
C
D
E
F
G
H
I
J
M
J
J
J
K
L
Patent No. D692290
Assure hood is fully secure by undamaged Jeep® front latch & supplemental side
catches.
Do not modify hood or catches to defeat intended safety of Jeep® primary latch &
supplemental catch system.
Hood catch is intended only as supplemental to Jeep® supplied latch at front of hood.
To avoid risk of property damage or injury: Always;
CAUTION
!
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Page 2/3
1. Remove the factory hood catch.
2. Remove the pivot base from the Aluminum Hood Catch
assembly.
JEEP® TJ ALUMINUM HOOD CATCH Patent No. D692290
4. Re-attach the Aluminum Hood Catch assembly to the
pivot base using the binding posts removed in Step 2.
3. Fasten the catch to the hood. Fasten the pivot base to the
fender.
Be sure safety snap is securely attached to catch.
NOTICE
11210.15 (Black)
11210.18 (Textured)
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
5. Adjust the Aluminum Hood Catch by rst releasing the latch.
With jam nuts loose, rotate latch clockwise to increase tension or
counter clockwise to decrease tension. When adjusted properly,
hood should contact and slightly compress the hood bumper.
Be sure adjustment rod has thread engagement
equal or greater to 3 threads on each end. Operating vehicle with
inadequate thread engagement could result in damage to
vehicle.
6. Your Aluminum Hood Catch is installed and road ready!
Page 3/3
NOTICE
JEEP® TJ ALUMINUM HOOD CATCH Patent No. D692290
11210.15 (Black)
11210.18 (Textured)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Rugged Ridge 11210.15 Installation guide

Type
Installation guide
This manual is also suitable for

Rugged Ridge 11210.15 Aluminum Hood Catch is a supplemental hood latch designed for Jeep® TJ models. It provides additional security to the front latch and prevents the hood from accidentally opening due to vibrations or rough terrain. The catch is adjustable to ensure a snug fit, and it comes with all necessary hardware for easy installation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI