2. Rugged Ridge
  3. 11116.07

Rugged Ridge 11116.07, 11210.11, 11210.17, Aluminum Hood Catch Installation guide

  • Hello! I have reviewed the installation instructions for the OMIX-ADA JK aluminum hood catch. This document provides a step-by-step guide on how to install the supplemental hood catch, including the removal of the factory catch, installation of the new catch components, and adjustments. I'm ready to answer any questions you might have about this product.
  • What is the purpose of this hood catch?
    What should I always assure when using this catch?
    What should I avoid when using this catch?
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Page 1/3
11116.07 (Silver)
11210.11 (Black)
JEEP® JK ALUMINUM HOOD CATCH
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
Contents:
• A - Latch
• B - Latch Joint
• C - Pivot Base Joint
• D - Pivot Base
• E - Catch
• F - Pivot Base Gasket
• G - Catch Gasket
• H - Flat Head Bolts
• I - Lock Nuts
• J - Binding Posts
• K - Jam Nuts
• L - Adjustment Rod
• M - Safety Snap
Suggested Tools:
• Basic Hand Tools
A
B
C
D
E
F
G
H
I
J
M
J
J
J
K
L
PATENT PENDING
• Assure hood is fully secure by undamaged Jeep® front latch & supplemental side
catches.
• Do not modify hood or catches to defeat intended safety of Jeep® primary latch &
supplemental catch system.
Hood catch is intended only as supplemental to Jeep® supplied latch at front of hood.
To avoid risk of property damage or injury: Always;
CAUTION
!
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Page 2/3
Figure 1
Figure 1
Figure 1
Figure 1
2. Pull/remove the hood bumper from the factory hood catch.
1. Remove the factory hood catch.
3. Remove the pivot base from the Aluminum Hood Catch
assembly.
4. Attach the hood bumper (Removed in Step 2) to the pivot
base.
11116.07 (Silver)
11210.11 (Black)
JEEP® JK ALUMINUM HOOD CATCHPATENT PENDING
460 Horizon Drive #400 | Suwanee, GA 30024 USA | www.omix-ada.com | Copyright © 2013 Omix-Ada®, Inc.
Figure 1
Figure 1
Figure 1
6. Re-attach the Aluminum Hood Catch assembly to the
pivot base using the binding posts removed in Step 3.
5. Fasten the catch to the hood. Fasten the pivot base to the
fender.
Be sure safety snap is securely attached to catch.
7.AdjusttheAluminumHoodCatchbyrstreleasingthelatch.
With jam nuts loose, rotate latch clockwise to increase tension or
counter clockwise to decrease tension. When adjusted properly,
hood should contact and slightly compress the hood bumper.
Be sure adjustment rod has thread engagement
equal or greater to 3 threads on each end. Operating vehicle with
inadequate thread engagement could result in damage to
vehicle.
8. Your Aluminum Hood Catch is installed and road ready!
Page 3/3
11116.07 (Silver)
11210.11 (Black)
NOTICE
NOTICE
JEEP® JK ALUMINUM HOOD CATCHPATENT PENDING
/