Argos 1913189 User manual

Type
User manual

This manual is also suitable for

Hamlin - Bedside
143/4235
Assembly Instructions - Please keep for future reference
Issue 1 - 28/10/13
152/5230
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important Please read these instructions fully before starting assembly
Dimensions
Width - 45,2cm
Depth - 44,8cm
Height - 50,5cm
145/6103
h y g e n a
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Care and maintenance
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use a dry cloth to clean the
product, furniture polish is
not recommended.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Components - Panels
Please check you have all the panels listed below
2
1Top panel
(45.2 x 44.8cm)
2Right side panel
(48.5 x 43cm)
3Left side panel
(48.5 x 43cm)
Top
Top
4Back panel
(44 x 44cm)
16 Drawer bottom x 2
(39.8 x 37.9cm)
Top front frame x 2
(42 x 6cm)
13 Bottom frame
(42 x 7cm)
9Large drawer right
side (40 x 12cm)
7Large drawer back
(36.6 x 12cm)
6Small drawer front
(43 x 15cm)
8Small drawer back
(36.6 x 8cm)
10 Large drawer left
side (40 x 12cm)
11 Small drawer right
side (40 x 8cm)
12 Small drawer left
side (40 x 8cm)
5Large drawer front
(43 x 19cm)
Unfinished bottom
frame (42 x 7cm)
14
15
NM
3
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
Wooden dowel x 32
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
D
14mm Screw x 32
E F
IG H
L
JK
Right runner
x 4 pair Left runner
x 4 pair
Plastic
cap x 8
20mm Screw x 4
40mm Screw x 4 Metal dowel x 8 Locking
nut x 8
Nail x 23 Nail x 4 Plastic
feet x 4
Plastic
bracket x 4
L shaped
bracket x 4
Step 1
Assembly Instructions
4
Insert dowels into the
indicated parts.
A
A
2
3
9
11
A
A
A
A
A
A
A
A
A
7
A
15
2x
13
A
12
10
8
A
A
A
14
A
Step 2
Step 3
Assembly Instructions
5
Fixing runners.
Attach right runners
to the pre drilled holes
on the right side panel
using screws .
Attach left runners
to the pre drilled holes on
the left side panel
using screws .
Fitting Metal dowels.
Screw metal dowels
into top panel , large
drawer front and small
drawer front .
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
E
1
6
5
1
2
M
B2
3
B
N
B
3
M
M
B
N
N
E
E
E
E
E
E
E
5
6
Step 4
Step 5
Step 6
Fixing L shaped brackets.
Fix L shaped brackets
in the bottom frame
and unfinished bottom
frame using screws
, as shown.
Attention: Leave
space from the1mm
edge of the bars as shown.
L shaped brackets must be
fixed to the unfinished side
in bottom frame .
Fixing left side panel.
Place left side panel
properly ensuring dowels
and front frames are all
fitted into their holes at
the same time.
Fix bottom frames and
in the left side panel
L shapedthrough
brackets using screws
, as shown.
Assembling frames.
Fit bottom frame and
and top front frames
into holes on right
side panel , as shown.
Then, fix bottom frames
and in the right
side panel through L
shaped brackets using
screws .
Finished sides to
face outside and
finished edges to face up.
1mm
Attention:
Assembly Instructions
6
B
14
3
3
B
B
B
B
K
2
B
13
K
K
K
13
K
2
13
K
13
3
K
K
13
13
K
Unfinished side
Finished sides to face
outside and finished
edges to face up.
14
K
K
13 14
13
14
14
15
15
15
K
14
14
13 14
Assembly Instructions
7
Step 7
Step 8
Fixing top panel.
With help, carefully
stand the product upright.
With help, fit top panel
to the cabinet.
Insert 4 locking nuts
into side panels where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
.
Fixing back panel.
Important:
Cabinet beMUST
‘square’ when back panel
is attached.
Attach back panel
using nails .
F
1
4
L
1
F
F
F
F
L
F
G
4
G
G
G
Finished edge
Assembly Instructions
8
Step 9
Step 10
Attach plastic feets.
With help, carefully lay
down the product.
Attach p inlastic feets
the bottom edge of the
right and left side panels
using nails .
Make sure nails
are fully nailed.
After attach plastic feets,
with help, carefully stand
the product upright.
D
16
c: With help, fit large
drawer front to the
drawer sides.
Insert 2 locking nuts
into drawer sides where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
.
Large drawer
assembly.
a: Fix large drawer
sides and to the
large drawer back
using screws .
b: Slide drawer bottom
into slots on drawer
sides.
10
a:
b:
c:
I
H
I
I
I
H
I
79
10
D
F
5
FFL
9
7
D
16
5
F
F
L
Assembly Instructions
9
Step 11
c: With help, fit small
drawer front to the
drawer sides.
Insert 2 locking nuts
into drawer sides where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
.
Small drawer
assembly.
a: Fix small drawer
sides and to the
small drawer back
using screws .
b: Slide drawer bottom
into slots on drawer
sides.
Step 12
Attach plastic bracket.
Attach plastic bracket
in the bottom of the large
and small drawers using
screws .
J
C
D
16
a:
b:
c:
D
F
FFL
811
12
6
11 12
8
D
15
16
6
F
F
L
J
J
C
Assembly Instructions
10
Step 13
Fixing runners.
Attach right runners
and left runners in the
bottom edge of the large
and small drawers using
screws , as shown.
Make sure
runners are
correctly positioned
according to the diagram
prior to fixing.
B
Step 14
Hook the wheels of the
runner on the back of the
drawers over the wheels
of the runners on the left
and right sides, then hold
the drawers level and
slide backwards into
position.
Assembly is complete.
M
N
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
B
B
N
M
IN FLUSH
IN FLUSH
Correct position of the screws.
BB
B
B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Argos 1913189 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI