Argos Darcy TV Stand 392/5591 User manual

Brand
Argos
Model
Darcy TV Stand 392/5591
Type
User manual

This manual is also suitable for

Dimensions
Width - 159.3 cm
Depth - 50 cm
Height - 53.7 cm
Darcy - TV Stand
392/5591
Important - Please read these instructions fully before starting assembly
Issue 1 - 03/06/2015 1
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400 800
!Safety and Care Advice
Important - Please read these instructions fully before starting assemb ly
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately 48 kgs.
Please lift with care.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly .Keep this page with
these instructions for future
reference.
2
• Check you have all the
components and tools listed on
pages 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels during assembly,
this could cause damage.
• Assemble the unit as close
to its final position (in the same
room) as possible.
Please check you have all the panels listed below
3
13
4
2
Right side
(44.6 x 49.8cm)
Left side
(44.6 x 49.8cm) Top
(159.3 x 50.0cm)
Bottom
(159.3 x 50cm)
5
Shelf
(57.5 x 42.8cm)
6
Vertical
partition
(44.6 x 46.7cm)
8
Front support
(96.3 x 8cm)
9
Long plinth x 2
(148.9 x 5cm)
10
Short plinth x 2
(40.7 x 5cm)
11
Flap
(59.6 x 44cm)
12
Drawer front x 2
(95.7 x 20.6cm)
13
Drawer back x 2
(90.7 x 12cm)
14
Drawer left side x 2
(40 x 12cm)
15
Drawer right side x 2
(40 x 12cm)
16
Drawer base x 2
(93.8 x 40,5cm)
17
Rear (156.9 x 45.9cm)
Component - Panels If you have damaged or missing components
call the Customer Helpline: 0845 6400 800
Components - Fittings
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
4
I
(7x50) Hexagon bolt x 10
Wooden dowel x 56 (8x35) Hinge plate x 2
4x13mm Screw x 4 5x13mm Screw x 12
Cap x 12
Cap x 10
Metal dowel x 12
Handle x 5
Locking nuts x 12
( 15x13)
Door hinge x 2
CC
F
A
C
D E
H
B
G
J
3x16mm Screw x 24
3,5x16mm Screw x 22
O
P
Stabilizer x 12
S
Mounting bracket x 8
W
Height adjuster x 1
X
Bumper x 2
T
K
3.5x27mm Screw x 10
HL
3x20mm Screw x 12
M
Allen key x 1
N
Feet x 6
Q
Flap stay x 2
R
Runner x 2
U
Runner x 2
V
Shelf support x 5
Y
Assembly instructions
Step 1Step 1
Insert locking nuts
into the right side panel
.
Insert wooden dowels
into the right side panel
.
Screw metal dowels .
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
A
F
a:
A
A
AH
H
F
F
A
A
A
2
2
F
A
H
U
U
E
U
b: Position runners
Position runners 38mm
from front edge
of the left side panel .
Fix runners with screws .
Mark the top right with a
punch. Screw into the
hole.
b:
O
2
2
2
5
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
Tools required
Punch
U
O
E EE
38
a: Inserting dowels
and locking nuts
Assembly Instructions
Step 1Step 2
Insert locking nuts
into the vertical partition
.
Insert wooden dowels
into the vertical partition
.
Screw metal dowels .
Rotate vertical partition.
Insert shelf support
into the vertical partition.
6
6
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
A
F
a:
b:
F
A
Finished
Finished
Finished
Finished
front edge
front edge
front edge
front edge
A
A
AF
H
H
F
Y
Y
Y
A
A
A
6
6
6
6
U
U
H
E
U
b: Position runners
Position runners 40mm
from front edge
of the vertical partition .
Fix runners with screws .
Mark the top right with a
punch. Screw into the
hole.
Rotate vertical partition.
Attach flap stay using
screws .
O
6
R
R
R
P
P
P
P
6
U
O
E E
38
E
a: Inserting dowels
and locking nuts
Step 1Step 2Step 1Step 3
Insert locking nuts
into the left side panel
.
Insert wooden dowels
into the left side panel .
Insert shelf support
into the left side panel.
1
1
A
F
a:
b:
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
b: flap stay Attach
flap stay usingAttach
screws .
Y
Y
Y
F
A
F
FA
A
A
A
A
A
1
1
R
R
R
R
P
PP
P
7
a: Inserting dowels
and locking nuts
Assembly Instructions
Step 4
Screw metal dowels
into the top .
Insert shelf support
Attach “hinge plates"
into the bottom .
3
4
Step 5
3
4
H
H
H
H
HY
Y
H
H
B
B
B
B
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
Insert locking nuts
into the front support .
Repeat with back
support .
Insert wooden dowels
into the front support .
Repeat with back
support .
7
7
78
8
8
F
A
A
A
A
A
F
F
F
F
A
8
a: Inserting dowels
Assembly Instructions
Step 6
11
9
9
11
C
C
D
D
Fitting hinges to doors
Fix 2 hinges to the
flap using screws .
CD
Step 7
10
10
A
A
AA
A
A
A
Insert wooden dowels
into the long plinth .
Repeat with short
plinth .
A
A
A
A
A
x2
x2
9
Assembly Instructions
Step 8
Attaching panels
Attach right side panel
to the front support .
Attach vertical partition
to the front support
Use the allen key to
turn locking nuts
clockwise to lock.
Cover locking nuts
with caps .
A
F
H
A
F
H
F
G
N
F
G
N
3
22
22
1
1
22
8
8
3
8
8
6 6
6
G
N
Attaching panels
Attach right side panel
Attach vertical partition
Attach left side panel
to the top .
Use the allen key to
turn locking nuts
clockwise to lock.
Cover locking nuts
with caps .
22
6
G
N
Step 9
10
Assembly Instructions
17
Step 10
Attaching rear panel
Slide rear panel
into grooves of
top , side panels
and .
3
1 2
9
9
9
9
9
9
9
10
10
10
10
10
10
17
a: Attaching plinth
Attach feet to the
long plinth
Attach long plinth
to the short plinth .
b: Attaching plinth
Attach long plinth
& short plinth to the
bottom .
Step 11
3
Q
Q
QQ
Q
Q
Q
22
8
6
1
a:
b:
44
11
Assembly Instructions
Step 12
6
9
9
9
9
10
10
10
10
4
4
4
Attaching bottom
Attach bottom to the sides
& vertical partition using
hexagon bolt
& allen key .
Cover with caps .
Step 13
22
1
P
P
P
W W W
W
W
WW WW
W
W
W
W
17
I
N
J
I
I
I
I
I
N
I
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
sliders in place.
!
J
I
J
12
3
I
Mounting bracket
Place mounting
bracket onto the
assembly as shown.
Mark holes with a
punch and fix the
bracket with screws .
Assembly Instructions
Step 14
IMPORTANT !
Cabinet MUST
be “square”
when rear panel
is attached.
!
Fixing rear panels
Fix rear panel
to back of TV stand
using stabilizer .
SS
S
S
SS
S
S
SS
17
13
Assembly Instructions
Step 15
A
Insert wooden dowels
into the drawer back .
13
a: drawer back:
A
Drawer assembly
b:
a:
F
A
b: Insert locking nuts
into the drawer sides
&
F
FF
Insert wooden
dowels into the
drawer sides .
A
14
14
15
15
c:
12
12
c: Screw metal dowels
into the drawer front .
H
H
H
H
13
14
15
d:
13
I
I
I
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
A
A
A
A
x2
x2
x2 x2
13
A
A
A
A
d:Fix drawer sides
&
to the drawer back using
hexagon bolt .
Cover bolts with caps .
14 15
J
I
J
N
I
J
14
Assembly Instructions
Step 16
Drawer assembly
a: Attach drawer front
to the drawer sides.
Use the allen key to
turn locking nuts
clockwise to lock.
Cover locking nuts
with caps .
b:
a:
c:
IMPORTANT!
Drawer MUST
be “square”
when base is
attached.
c: Attach runner using
screws .
Repeat step 15 & 16 for all
drawers.
!
12
12
M
H
HM
M
V
V
V
V
V
16
A
F
H
F
G
F
G
b: Attach drawer base
using screws &
stabilizer .
16
16
16
16
13
13
N
N
14
15
S
S
S
O
OOOOOOO
15
Assembly Instructions
x2
x2
x2
Step 17
16
11
12
12
5
5
5
4
L
L
L
LL LL
K
K
KK
KK
Hinge adjustment
B
C
B
C
R
O
R
O
Hanging flap
Insert drawers to the
cabinet.
a: slot flap hinges onto
‘hinge plates’.
b: Tighten screw
shown to lock hinges in
position.
Adjust hinges so that gaps
around the flap is even.
Fix flap stay to the flap
using screws .
Insert Shelf .
Attach bumper onto
the shelf .
Place a spirit level on
top .
Where necessary, insert
height adjuster to
make top level.
Attach door handles
using screws .
Assembly is complete.
C
a: b:
R
O
5
T
TT
X
X
3
3
3
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400 800
Assembly Instructions
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Argos Darcy TV Stand 392/5591 User manual

Brand
Argos
Model
Darcy TV Stand 392/5591
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents