Short Guide
Downloading images from the QS I system
cobas p 512/ 612
Roche PVT GmbH
Maybachstrasse 30
D-71332 Waiblingen
Germany
cobas p 512/ 612 Downloading images from QS I
Short Guide – V1.0 – 01/2013 2/6
Disclaimer
This manual is a product of Roche PVT GmbH.
All rights are reserved. No part of this manual may be reproduced in any form (print, photocopy,
microfilm or another procedure) or processed using electronic systems, copied or distributed without
the written permission of Roche PVT GmbH. Roche PVT GmbH assumes no liability for any errors,
omissions or damages resulting from the use of the information contained in this manual.
Neither Roche PVT GmbH nor its subsidiaries assume any liability to the purchaser of this product or
any third parties for damages, losses, costs or expenses incurred by the purchaser or third parties due
to accident, misuse of the product or unapproved modifications, repairs or improvements to the
instrument.
Roche PVT GmbH assumes no liability for damages or disruptions resulting from the use of options or
accessories that are not original Roche PVT products or that do not have express approval from
Roche PVT GmbH.
Note: All of the product names contained in this manual are trademarks of the respective companies.
If the trademark symbols © or ® are not included, it can not be assumed that the name is an
unregistered product name.
The content of this manual is subject to change without any communicative obligations
by Roche PVT GmbH.
Copyright by Roche PVT GmbH, Waiblingen 2013
cobas p 512/ 612 Downloading images from QS I
Short Guide – V1.0 – 01/2013 3/6
1. Network connection to the Image Folder
The following steps assume a working LAN connection between the system and the workstation being
used for access, as depicted below.
Figure 1: Physical network connection diagram
LAN socket
labeled
'Host Network'
cobas p 512/ 612 Downloading images from QS I
Short Guide – V1.0 – 01/2013 4/6
2. R etrieving the sys tem's IP address
Figure 2: Screen Customer Configuration (exemplary)
1. Start the cobas p 512 or cobas p 612 system.
2. In the QNX system change to 'Service ► Extended Menu ► Configuration ► Customer
Configuration' and make a note of the address found in the field 'System IP - Address'.
3. Downloading images via Windows E xplorer
1. Connect your workstation to the cobas p 512 or cobas p 612 system, as shown in Figure 1.
2. Click the Windows Explorer icon to open the Windows Explorer file navigator.
Figure 3: Windows Explorer icon
cobas p 512/ 612 Downloading images from QS I
Short Guide – V1.0 – 01/2013 5/6
3. In the target line at the top, enter the following:
"ftp://user:password@System IP - Address/../../qs1/Host/"
NOTICE
The system IP address is to be found under 'Service ► Extended Menu ► Configuration ►
Customer Configuration ► System IP - Address' (see Figure 2).
This is the IP address of the QNX computer to which the QS I directory 'Host'
containing the image files is mounted.
User and password conform to the credentials used for accessing
the system's control computer on the service level.
Pay particular attention to upper and lower case letters.
If the service credentials are unknown, ask Roche PVT support for advice.
4. Press the 'Enter' key.
The following screen will be displayed (exemplary):
Figure 4: Windows Explorer
5. By 'Copy and Paste'. transfer the desired image files from the 'Host' directory into a folder on your
workstation to where you wish to store the image data.
CAUTION
Do not move or change any files or even so much as navigate outside the
'Host' directory! You may inadvertently render the system inoperative.
cobas p 512/ 612 Downloading images from QS I
Short Guide – V1.0 – 01/2013 6/6
4. Downloading images via FTP (optional)
As an option, image files can also be downloaded via FTP. Independently of the FTP client being used,
default settings should generally be favored. The Transfer Mode 'binary' should be used as images will
corrupt if not downloaded in binary format.
Within the FTP client on your computer, configure the connection manager with these parameters:
1. Enter the system's host address.
2. Select 'automatic detection' type.
3. Enter user and password conform to the credentials used for accessing the system's control
computer on the service level. Pay particular attention to upper and lower case letters.
4. Determine the remote path: '/../../qs1/Host'.
5. Determine the local path to where you wish to store the image data.
Figure 5: Exemplary FTP connection manager
6. Connect to the remote directory 'Host' containing the QS I image files.
7. Once the FTP connection has been successfully established,
save the relevant images to your PC.
CAUTION
Do not move or change any files or even so much as navigate outside the
'Host' directory! You may inadvertently render the system inoperative.
1.
2.
4.
5.
3.
-
1
-
2
-
3
-
4
-
5
-
6
Roche cobas p 612 Short Guide
- Type
- Short Guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Roche cobas p 512 Short Guide
-
-
-
-
-
-
-
-
-